Enigma 2 by The_ripper - TEST -

[rudiniiwwa]

ok I have new cable and now is :

Setting up Clean Divider 2 to 96000000Hz.
Setting up Clean Divider 4 to 33333333Hz.
Setting up Clean Divider 5 to 25000000Hz.
Setting up Clean Divider 6 to 20000000Hz.
Setting up Clean Divider 7 to 20000000Hz.
GPIO dir/data = 0x76000038/0x76000000
UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
UART1 GPIO mode/dir/data = 0x6e/0x00/0x00
XENV block processing completed.
Found existing memcfg: DRAM0(0x08000000), DRAM1(0x08000000)
Heap/Temp/Temp1/Dest start at 0x14000000/0x16000000/0x15000000/0x12000000.
Default boot index: 0
Scanning ROMFS image at 0x8c040000 (0x48040000) .. Found.
ROMFS found at 0x8c040000, Volume name = YAMON_XRPC
Found 1 file(s) to be processed in ROMFS.
Processing xrpc_xload_yamon_ES4_prod.bin (start: 0x8c040090, size: 0x0002fe84)
Checking zboot file signature .. Not found.
Trying xrpc_xload format .. OK
Checking zboot file signature at 0x13000000 .. OK
Decompressing to 0x91200000 .. OK (453328/0x6ead0).
Load time total 173/255 msec.
Execute final at 0x91200000 ..



********************************* *
* YAMON ROM Monitor
* Revision 02.06-SIGMADESIGNS-01-2.8.0.1
********************************* *
Memory: code: 0x11000000-0x11040000, 0x11200000-0x11204000
reserved data: 0x11240000-0x12440000, PCI memory: 0x12440000-0x12840000
Environment variable 'start' exists. After 1 seconds
it will be interpreted as a YAMON command and executed.
Press Ctrl-C (or do BREAK) to bypass this.

xosPe0 serial#b368b1126ee60d044a683e91cb c18f42 subid 0x50
xenv cs2 ok
xosPe0 serial#b368b1126ee60d044a683e91cb c18f42 subid 0x50
xenv cs2 ok
power supply: ok
dram0 ok (8)
dram1 ok (9)
zboot (0) ok
>
********************************* *****
* SMP863x zboot start ...
* Version: 2.4.0-2.8.0.1
* Started at 0x91000000.
* Configurations (chip revision: 6):
* Use 8KB DRAM as stack.
* Support XLoad format.
* Enabled BIST mode.
* Enabled memory test mode.
* Use internal memory for stage0/1.
********************************* *****
Boot from flash (0x48000000) mapped to 0x8c000000.
Found XENV block at 0x8c000000.
CPU clock frequency: 300.37MHz.
System clock frequency: 200.25MHz.
DRAM0 dunit_cfg/delay0_ctrl (0xf34111ba/0x000a7787).
DRAM1 dunit_cfg/delay0_ctrl (0xf34111ba/0x000a7777).
Using UART port 0 as console.
Board ID.: "852-E2"
Chip Revision: 0x8634:0x86 .. Matched.
Setting up H/W from XENV block at 0x8c000000.
Setting <SYSCLK avclk_mux> to 0x00000000.
Setting <SYSCLK hostclk_mux> to 0x00000100.
Setting <IRQ rise edge trigger lo> to 0xff28ca00.
Setting <IRQ fall edge trigger lo> to 0x0000c000.
Setting <IRQ rise edge trigger hi> to 0x0000009f.
Setting <IRQ fall edge trigger hi> to 0x00000000.
Setting <IRQ GPIO map> to 0x20090820.
Setting <PB default timing> to 0x10101010.
Setting <PB timing0> to 0x10101010.
Setting <PB Use timing0> to 0x000003f4.
Setting <PB timing1> to 0x00110101.
Setting <PB Use timing1> to 0x000003f3.
Setting <PB timing2> to 0x105f1010.
Setting <PB Use timing2> to 0x000003f8.
PB cs config: 0x000e0040 (use 0x000e0040)
Enabled Devices: 0x00021ace
BM/IDE PCIHost Ethernet I2CM I2CS USB PCIDev2 PCIDev3 SCARD
MAC: 0014:15:51:e0
PCI IRQ routing:
IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
IDSEL 3: INTA(#15) INTB(#15) INTC(#15) INTD(#15)
Smartcard pin assignments:
OFF pin = 0
5V pin = 1
CMD pin = 2
Setting up Clean Divider 2 to 96000000Hz.
Setting up Clean Divider 4 to 33333333Hz.
Setting up Clean Divider 5 to 25000000Hz.
Setting up Clean Divider 6 to 20000000Hz.
Setting up Clean Divider 7 to 20000000Hz.
GPIO dir/data = 0x76000038/0x76000000
UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
UART1 GPIO mode/dir/data = 0x6e/0x00/0x00
XENV block processing completed.
Found existing memcfg: DRAM0(0x08000000), DRAM1(0x08000000)
Heap/Temp/Temp1/Dest start at 0x14000000/0x16000000/0x15000000/0x12000000.
Default boot index: 0
Scanning ROMFS image at 0x8c040000 (0x48040000) .. Found.
ROMFS found at 0x8c040000, Volume name = YAMON_XRPC
Found 1 file(s) to be processed in ROMFS.
Processing xrpc_xload_yamon_ES4_prod.bin (start: 0x8c040090, size: 0x0002fe84)
Checking zboot file signature .. Not found.
Trying xrpc_xload format .. OK
Checking zboot file signature at 0x13000000 .. OK
Decompressing to 0x91200000 .. OK (453328/0x6ead0).
Load time total 173/255 msec.
Execute final at 0x91200000 ..



********************************* *
* YAMON ROM Monitor
* Revision 02.06-SIGMADESIGNS-01-2.8.0.1
********************************* *
Memory: code: 0x11000000-0x11040000, 0x11200000-0x11204000
reserved data: 0x11240000-0x12440000, PCI memory: 0x12440000-0x12840000
Environment variable 'start' exists. After 1 seconds
it will be interpreted as a YAMON command and executed.
Press Ctrl-C (or do BREAK) to bypass this.

xrpc failed (9)--- if a xtask is using a cipher or if you reboot
--- xrpc will fail with RM_BUSY
Checking zboot signature.. it's not zboot file.
Error : Internal, code = ffffffff
YAMON> xosPe0 serial#b368b1126ee60d044a683e91cb c18f42 subid 0x50
xenv cs2 ok
xosPe0 serial#b368b1126ee60d044a683e91cb c18f42 subid 0x50
xenv cs2 ok
power supply: ok
dram0 ok (8)
dram1 ok (9)
zboot (0) ok
>
********************************* *****
* SMP863x zboot start ...
* Version: 2.4.0-2.8.0.1
* Started at 0x91000000.
* Configurations (chip revision: 6):
* Use 8KB DRAM as stack.
* Support XLoad format.
* Enabled BIST mode.
* Enabled memory test mode.
* Use internal memory for stage0/1.
********************************* *****
Boot from flash (0x48000000) mapped to 0x8c000000.
Found XENV block at 0x8c000000.
CPU clock frequency: 300.37MHz.
System clock frequency: 200.25MHz.
DRAM0 dunit_cfg/delay0_ctrl (0xf34111ba/0x000a7787).
DRAM1 dunit_cfg/delay0_ctrl (0xf34111ba/0x000a7777).
Using UART port 0 as console.
Board ID.: "852-E2"
Chip Revision: 0x8634:0x86 .. Matched.
Setting up H/W from XENV block at 0x8c000000.
Setting <SYSCLK avclk_mux> to 0x00000000.
Setting <SYSCLK hostclk_mux> to 0x00000100.
Setting <IRQ rise edge trigger lo> to 0xff28ca00.
Setting <IRQ fall edge trigger lo> to 0x0000c000.
Setting <IRQ rise edge trigger hi> to 0x0000009f.
Setting <IRQ fall edge trigger hi> to 0x00000000.
Setting <IRQ GPIO map> to 0x20090820.
Setting <PB default timing> to 0x10101010.
Setting <PB timing0> to 0x10101010.
Setting <PB Use timing0> to 0x000003f4.
Setting <PB timing1> to 0x00110101.
Setting <PB Use timing1> to 0x000003f3.
Setting <PB timing2> to 0x105f1010.
Setting <PB Use timing2> to 0x000003f8.
PB cs config: 0x000e0040 (use 0x000e0040)
Enabled Devices: 0x00021ace
BM/IDE PCIHost Ethernet I2CM I2CS USB PCIDev2 PCIDev3 SCARD
MAC: 0014:15:51:e0
PCI IRQ routing:
IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
IDSEL 3: INTA(#15) INTB(#15) INTC(#15) INTD(#15)
Smartcard pin assignments:
OFF pin = 0
5V pin = 1
CMD pin = 2
Setting up Clean Divider 2 to 96000000Hz.
Setting up Clean Divider 4 to 33333333Hz.
Setting up Clean Divider 5 to 25000000Hz.
Setting up Clean Divider 6 to 20000000Hz.
Setting up Clean Divider 7 to 20000000Hz.
GPIO dir/data = 0x76000038/0x76000000
UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
UART1 GPIO mode/dir/data = 0x6e/0x00/0x00
XENV block processing completed.
Found existing memcfg: DRAM0(0x08000000), DRAM1(0x08000000)
Heap/Temp/Temp1/Dest start at 0x14000000/0x16000000/0x15000000/0x12000000.
Default boot index: 0
Scanning ROMFS image at 0x8c040000 (0x48040000) .. Found.
ROMFS found at 0x8c040000, Volume name = YAMON_XRPC
Found 1 file(s) to be processed in ROMFS.
Processing xrpc_xload_yamon_ES4_prod.bin (start: 0x8c040090, size: 0x0002fe84)
Checking zboot file signature .. Not found.
Trying xrpc_xload format .. OK
Checking zboot file signature at 0x13000000 .. OK
Decompressing to 0x91200000 .. OK (453328/0x6ead0).
Load time total 173/255 msec.
Execute final at 0x91200000 ..



********************************* *
* YAMON ROM Monitor
* Revision 02.06-SIGMADESIGNS-01-2.8.0.1
********************************* *
Memory: code: 0x11000000-0x11040000, 0x11200000-0x11204000
reserved data: 0x11240000-0x12440000, PCI memory: 0x12440000-0x12840000
Environment variable 'start' exists. After 1 seconds
it will be interpreted as a YAMON command and executed.
Press Ctrl-C (or do BREAK) to bypass this.

xrpc failed (9)--- if a xtask is using a cipher or if you reboot
--- xrpc will fail with RM_BUSY
Checking zboot signature.. it's not zboot file.
Error : Internal, code = ffffffff
YAMON>


but ctr-c or break is not working, and i can`t write on YAMON> Any ideas?

[rudiniiwwa]

i try connect to azbox on ubuntu. I use minicom, but with the same result like putty - no ctrl-c and no way to write enything. Please help :(

[Sentosa72]

https://www.satpimps.co.uk/showthread.php?t=134446

[Sentosa72]

i try connect to azbox on ubuntu. I use minicom, but with the same result like putty - no ctrl-c and no way to write enything. Please help :(

Azbox TTL manual

[rudiniiwwa]

https://www.satpimps.co.uk/showthread.php?t=134446

I know the procedure, but why I can`t use my keybord in putty???

[mworker]

I know the procedure, but why I can`t use my keybord in putty???

Just a hint,
when i was trying to recover my azbox, on my computer i had two windows open.One window was putty and the other one the pdf guide by pr2 for recovering.
It took me a long time to understand why ctr-c was not working for me,but the answer was simple.
Putty window was not active when i was pressing ctrl-c,it was the guide window active.
So make sure putty window is active and also you must press ctrl-c really fast when you see the message on putty.

[rudiniiwwa]

Just a hint,
when i was trying to recover my azbox, on my computer i had two windows open.One window was putty and the other one the pdf guide by pr2 for recovering.
It took me a long time to understand why ctr-c was not working for me,but the answer was simple.
Putty window was not active when i was pressing ctrl-c,it was the guide window active.
So make sure putty window is active and also you must press ctrl-c really fast when you see the message on putty.

I have only putty open, and still i can`t press Ctrl-C

[happyhammer]

i have a box where i cant enter CRTL-C to break into YAMOM. I was trying out the serial port connections by trial and error before i found out the proper connections, so i'm assuming i have blown the uart0 port on the chip.(its TX outputs OK, but its RX is not working and so CTRL-C has no effect.

Maybe you connected up VCC to TX or RX pin by mistake?

[rudiniiwwa]

i have a box where i cant enter CRTL-C to break into YAMOM. I was trying out the serial port connections by trial and error before i found out the proper connections, so i'm assuming i have blown the uart0 port on the chip.(its TX outputs OK, but its RX is not working and so CTRL-C has no effect.

Maybe you connected up VCC to TX or RX pin by mistake?

I connect only tx,rx and gnd from old gsm cable with pl2303 chip. I didn`t connect VCC. Maybe I made mistake in rx. I check this carrefully in home.

[Sentosa72]

GSM USB cable did not work for me, only serial port, and TTL converters Max232
I tried USB / RS232 cable connected RS232TTL converter, you can not respond to CTRL + c

[Sentosa72]

Another usb serial converter responded ctrl + c, in this case could not be written in the putty window

If you have a laptop without a serial port, you can try this:
Serial Express card

This works for me

[mworker]

I recovered my azbox with a CA-42 Nokia clone cable.
Maybe you can use the drivers i attached, which came with my cable.
Good luck.

[gepard1]

hi i have in my azbox premium rti core 1.1.4 and working but i want put orginal firmware.when im puting my usb fat32 with patch.bin is only showing rescue mode on vfd but not schowing ip.after feau seconds enigma2 starting.where is my mistake?box is conected to the lan with cable.

[Hectore]

Hello,

Put the original patch.bin on your memory stick.
When you are in rescue mode use JAZUP v1.3, jazup'll copy the official Kernel.
When Jazup reboot your azbox you drop on the official update screen.
Use USB upgrade option.

Regards.
Hectore

[larrywilson]

Amigos saludos, requiero ayuda intente colocar el fir enigma2 y mi equipo azbox elite no me arranca, la pantalla de tv esta en negro, me aparece 1- power on, 2- usb chek (el pen dri tiene pach.bin enigma 2), 3 booting, 4 rescuer mode, 5 186.89.16.16.160 luego se queda por largo rato mostrado esa secuencia de numeros y nada, destaco que la primera vez que intente cargar la imagen el internet me fallo por no estar conectado el cable y luego de esto es que tiene pantalla negra pero cargo normalmente el firw al 100x100, fue luego de que se apago que no quiso reiniciar normal claro no tenia internet al momento de colocar la imagen, requiero ayuda de como colocar un firw de azbox y salir de este apuro para que el deco funcione agradesco su ayuda para revivir mi azbox elite hd.

[gepard1]

Thenk You Hector that works.Thanks

[Kuhnigotchi]

Sorry, wrong language ...

[Blagi]

Greetings friends, I need help try to put the fir azbox enigma2 and my elite team I started, the tv screen is in black, I get 1 - power on, 2 - usb chek (the pen dri has pach.bin enigma 2), 3 booting, 4 rescuer mode, 5 186.89.16.16.160 then stays for a long time shown that sequence of numbers and nothing underlined that the first time you try to load the image the internet bug me for not being connected the cable and then This screen is black but that is normally charged at 100x100 IRWF was after he refused to turn off that light normal restart did not have internet at the time of placing the image, I need help on how to place a IRWF by Phantom and out of this trouble for the deco work thank you for your help to revive my azbox elite hd.

Net translation...

[pateken]

There are developments from the last firmware rti4?

[Sjaak66]

There are developments from the last firmware rti4?

They are developing a different approach the new firm. It looks like it's going slower but they are trying to make it as stable as possible.
Have look at their site. Google RTI forum and You'll find it.