Enigma 2 by The_ripper - TEST -

[arcibald]

I can still connect with the serial cable. This is what comes up in Putty when I reboot the box:

xosPe0 serial#c795d7a7b13a488198f565e834 f44f62 subid 0x50
xenv cs2 ok
xosPe0 serial#c795d7a7b13a488198f565e834 f44f62 subid 0x50
xenv cs2 ok
power supply: ok
dram0 ok (8)
dram1 ok (9)
zboot (0) ok
>
********************************* *****
* SMP863x zboot start ...
* Version: 2.4.0-2.8.0.1
* Started at 0x91000000.
* Configurations (chip revision: 6):
* Use 8KB DRAM as stack.
* Support XLoad format.
* Enabled BIST mode.
* Enabled memory test mode.
* Use internal memory for stage0/1.
********************************* *****
Boot from flash (0x48000000) mapped to 0x8c000000.
Found XENV block at 0x8c000000.
CPU clock frequency: 347.62MHz.
System clock frequency: 231.75MHz.
DRAM0 dunit_cfg/delay0_ctrl (0xf34111ba/0x000a5555).
DRAM1 dunit_cfg/delay0_ctrl (0xf34111ba/0x000a6565).
Using UART port 0 as console.
Board ID.: "852-E2"
Chip Revision: 0x8634:0x86 .. Matched.
Setting up H/W from XENV block at 0x8c000000.
Setting <SYSCLK avclk_mux> to 0x00000000.
Setting <SYSCLK hostclk_mux> to 0x00000100.
Setting <IRQ rise edge trigger lo> to 0xff28ca00.
Setting <IRQ fall edge trigger lo> to 0x0000c000.
Setting <IRQ rise edge trigger hi> to 0x0000009f.
Setting <IRQ fall edge trigger hi> to 0x00000000.
Setting <IRQ GPIO map> to 0x20090820.
Setting <PB default timing> to 0x10101010.
Setting <PB timing0> to 0x10101010.
Setting <PB Use timing0> to 0x000003f4.
Setting <PB timing1> to 0x00110101.
Setting <PB Use timing1> to 0x000003f3.
Setting <PB timing2> to 0x105f1010.
Setting <PB Use timing2> to 0x000003f8.
PB cs config: 0x000e0040 (use 0x000e0040)
Enabled Devices: 0x00021ace
BM/IDE PCIHost Ethernet I2CM I2CS USB PCIDev2 PCIDev3 SCARD
MAC: 0014:15:4e:79
PCI IRQ routing:
IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
IDSEL 3: INTA(#15) INTB(#15) INTC(#15) INTD(#15)
Smartcard pin assignments:
OFF pin = 0
5V pin = 1
CMD pin = 2
Setting up Clean Divider 2 to 96000000Hz.
Setting up Clean Divider 4 to 33333333Hz.
Setting up Clean Divider 5 to 25000000Hz.
Setting up Clean Divider 6 to 20000000Hz.
Setting up Clean Divider 7 to 20000000Hz.
GPIO dir/data = 0x76000038/0x76000000
UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
UART1 GPIO mode/dir/data = 0x6e/0x00/0x00
XENV block processing completed.
Found existing memcfg: DRAM0(0x08000000), DRAM1(0x08000000)
Heap/Temp/Temp1/Dest start at 0x14000000/0x16000000/0x15000000/0x12000000.
Default boot index: 0
Scanning ROMFS image at 0x8c040000 (0x48040000) .. Found.
ROMFS found at 0x8c040000, Volume name = YAMON_XRPC
Found 1 file(s) to be processed in ROMFS.
Processing xrpc_xload_yamon_ES4_prod.bin (start: 0x8c040090, size: 0x0002fe84)
Checking zboot file signature .. Not found.
Trying xrpc_xload format .. OK
Checking zboot file signature at 0x13000000 .. OK
Decompressing to 0x91200000 .. OK (453328/0x6ead0).
Load time total 151/222 msec.
Execute final at 0x91200000 ..



********************************* *
* YAMON ROM Monitor
* Revision 02.06-SIGMADESIGNS-01-2.8.0.1
********************************* *
Memory: code: 0x11000000-0x11040000, 0x11200000-0x11204000
reserved data: 0x11240000-0x12440000, PCI memory: 0x12440000-0x12840000
Environment variable 'start' exists. After 1 seconds
it will be interpreted as a YAMON command and executed.
Press Ctrl-C (or do BREAK) to bypass this.

xrpc succeeded
Stopped due to Ctrl-C
YAMON>

I have just noticed that the display is now showing 'Booting'

Thanks for any help anyone can suggest.

Stephen

Another problem to be solved first is to disable hardware acceleration ...

System bus frequency* * : 231750000 Hz
CPU frequency* * * * ** : 347625000 Hz
DSP frequency* * * * ** : 347625000 Hz

With hardware acceleration disabled:

System bus frequency* * : 200250000 Hz
CPU frequency* * * * ** : 300375000 Hz
DSP frequency* * * * ** : 300375000 Hz

Thanks to @VVZ ... on Pristavka.de
To restore the default clock ... just set this variable xenv in YAMON console:

YAMON> setxenv -b x.pll3 0x01020057

Reboot and new set is ready ...

Regards

Arci

[SPF]

Thanks, shklifo

Here is the log when left to run:

Setting <PB timing1> to 0x00110101.
Setting <PB Use timing1> to 0x000003f3.
Setting <PB timing2> to 0x105f1010.
Setting <PB Use timing2> to 0x000003f8.
PB cs config: 0x000e0040 (use 0x000e0040)
Enabled Devices: 0x00021ace
BM/IDE PCIHost Ethernet I2CM I2CS USB PCIDev2 PCIDev3 SCARD
MAC: 0014:15:4e:79
PCI IRQ routing:
IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
IDSEL 3: INTA(#15) INTB(#15) INTC(#15) INTD(#15)
Smartcard pin assignments:
OFF pin = 0
5V pin = 1
CMD pin = 2
Setting up Clean Divider 2 to 96000000Hz.
Setting up Clean Divider 4 to 33333333Hz.
Setting up Clean Divider 5 to 25000000Hz.
Setting up Clean Divider 6 to 20000000Hz.
Setting up Clean Divider 7 to 20000000Hz.
GPIO dir/data = 0x76000038/0x76000000
UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
UART1 GPIO mode/dir/data = 0x6e/0x00/0x00
XENV block processing completed.
Found existing memcfg: DRAM0(0x08000000), DRAM1(0x08000000)
Heap/Temp/Temp1/Dest start at 0x14000000/0x16000000/0x15000000/0x12000000.
Default boot index: 0
Scanning ROMFS image at 0x8c040000 (0x48040000) .. Found.
ROMFS found at 0x8c040000, Volume name = YAMON_XRPC
Found 1 file(s) to be processed in ROMFS.
Processing xrpc_xload_yamon_ES4_prod.bin (start: 0x8c040090, size: 0x0002fe84)
Checking zboot file signature .. Not found.
Trying xrpc_xload format .. OK
Checking zboot file signature at 0x13000000 .. OK
Decompressing to 0x91200000 .. OK (453328/0x6ead0).
Load time total 151/222 msec.
Execute final at 0x91200000 ..



********************************* *
* YAMON ROM Monitor
* Revision 02.06-SIGMADESIGNS-01-2.8.0.1
********************************* *
Memory: code: 0x11000000-0x11040000, 0x11200000-0x11204000
reserved data: 0x11240000-0x12440000, PCI memory: 0x12440000-0x12840000
Environment variable 'start' exists. After 1 seconds
it will be interpreted as a YAMON command and executed.
Press Ctrl-C (or do BREAK) to bypass this.

xrpc succeeded
Checking zboot signature.. it's a zboot file, signature OK.
Decompressing to 0x90020000 ..
Output length: 0x0096843a(9864250)
load compressed zboot file from 0xb3000000 to 0x90020000 OK
Linux version 2.6.15-sigma (kevin@kevin-laptop) (gcc version 3.4.2) #138 PREEMPT Thu Jan 22 21:35:07 KST 2009
Configured for SMP863x (revision ES6/RevA), detected SMP8634 (revision ES9/RevC).
SMP863x/SMP865x Enabled Devices under Linux/XENV 0x48000000 = 0x00021ace
BM/IDE PCIHost Ethernet I2CM I2CS USB PCIDev2 PCIDev3 SCARD
Valid MEMCFG found at 0x10000fc0.
CPU revision is: 00019069
Determined physical RAM map:
memory: 02fe0000 @ 10020000 (usable)
User-defined physical RAM map:
memory: 06ae0000 @ 10020000 (usable)
On node 0 totalpages: 92928
DMA zone: 92928 pages, LIFO batch:31
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 0 pages, LIFO batch:0
HighMem zone: 0 pages, LIFO batch:0
Built 1 zonelists
Kernel command line: mem=107m console=ttyS0,115200
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 2048 (order: 11, 32768 bytes)
Using 173.813 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 96256k/109440k available (4425k kernel code, 13156k reserved, 1007k data, 4200k init, 0k highmem)
Calibrating delay loop... 344.06 BogoMIPS (lpj=172032)
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
NET: Registered protocol family 16
tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x08000000.
PCI: Initializing SMP863x/SMP865x PCI host controller
PCI: Remapped PCI I/O space 0x58000000 to 0xc8020000, size 64 kB
PCI: Remapped PCI config space 0x50000000 to 0xc8004000, size 10 kB
PCI: device 1 disabled
PCI: device 4 disabled
PCI: Configured SMP863x/SMP865x as PCI slave with 128MB PCI memory
PCI: Region size is 16384KB
PCI: Map DMA memory 0x10020000-0x16b00000 for PCI at 0x11000000
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
tangox frequency scaling module installed.
Created /proc/cpucache_info entry.
NTFS driver 2.1.25 [Flags: R/W DEBUG].
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
SGI XFS with no debug enabled
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
loop: loaded (max 8 devices)
nbd: registered device at major 43
tango2_enet: ethernet driver for SMP863x internal mac
tango2_enet: detected phy at address 0x01
tango2_enet: mac address 0014:15:4e:79
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: SMP863x/SMP865x Bus Mastering IDE controller
Probing IDE interface ide0...
physmap flash device CS2: 800000 at 48000000
CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Using physmap partition definition
Adding partition #1-#5
Creating 5 MTD partitions on "CS2: Physically mapped flash":
0x00000000-0x00020000 : "CS2-Part1"
0x00020000-0x00040000 : "CS2-Part2"
0x00040000-0x00080000 : "CS2-Part3"
0x00080000-0x00700000 : "CS2-Part4"
0x00700000-0x00800000 : "CS2-Part5"
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07 13:30:21 2005 UTC).
usbcore: registered new driver snd-usb-audio
ALSA device list:
No soundcards found.
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 4200k freed
mount: /etc/mtab: No such file or directory
Initializing random number generator... done.
===> Starting system configuration...
===> [0] replace busybox 1.15.2(udh***, ftpget, ftpput)
===> [1] VFD initializing...
[TD210] INITIALIZED END
[TD210] SLEEP MODE OFF
===> [2] USB 2.0 driver loading...
Using /lib/modules/2.6.15-sigma/kernel/drivers/usb/host/uhci-hcd.ko
USB Universal Host Controller Interface driver v2.3
PCI: Enabling device 0000:00:02.0 (0000 -> 0001)
uhci_hcd 0000:00:02.0: UHCI Host Controller
uhci_hcd 0000:00:02.0: HCRESET not completed yet!
uhci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:02.0: irq 22, io base 0x58000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Enabling device 0000:00:02.1 (0000 -> 0001)
uhci_hcd 0000:00:02.1: UHCI Host Controller
uhci_hcd 0000:00:02.1: HCRESET not completed yet!
uhci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:02.1: irq 22, io base 0x58000020
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Using /lib/modules/2.6.15-sigma/kernel/drivers/usb/host/ehci-hcd.ko
PCI: Enabling device 0000:00:02.2 (0000 -> 0002)
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: irq 22, io mem 0x60008000
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
===> [3] File system checking...
check hda
check hdb
Cannot find HDD
===> [4] Make device files
mknod: /dev/mum0: File exists
mknod: /dev/em8xxx0: File exists
===> [5] Export hostname
hostname: /etc/hostname: No such file or directory
Starting network...
ifup: /etc/network/interfaces: No such file or directory
===> Starting services...
===> [1] telnetd starting...
===> Starting MMP custom setting...

(none) login: llad: module license 'LGPL' taints kernel.
em8xxx [/DATA/Yellow/Working/SigmaDesign8634/SMP8634-2805/mrua_SMP8634_2.8.0.5_GCC4_facspro d_legacy_dev.mips.nodts/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1346] init_module: begun
em8xxx0 [/DATA/Yellow/Working/SigmaDesign8634/SMP8634-2805/mrua_SMP8634_2.8.0.5_GCC4_facspro d_legacy_dev.mips.nodts/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1228] identify: board as unknown subid
em8xxx [/DATA/Yellow/Working/SigmaDesign8634/SMP8634-2805/mrua_SMP8634_2.8.0.5_GCC4_facspro d_legacy_dev.mips.nodts/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1332] identify: device 0x8634 0x86 accepted with software tango2revA
mumk_register_tasklet: (0) tasklet c8099000 status @c8d594b4
em8xxx [/DATA/Yellow/Working/SigmaDesign8634/SMP8634-2805/mrua_SMP8634_2.8.0.5_GCC4_facspro d_legacy_dev.mips.nodts/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1464] init_module: done. Found 1 em8xxx

It scrolled down as far as check hda and seemed to stop. I was just about to copy and paste that for you and it started to scroll more. I now have an Upgrade screen on my TV and the box displaying UPDATE:USB. This seems like progress. Just to have something on the TV screen seems like a miracle after 2 weeks without a picture!

What should I do next?

Arcibald, can I remove the hardware acceleration from this point?

Thanks, guys.

Stephen

[arcibald]

Yes ... but reboot after ! Before you try to UPDATE USB Procedure ...

Regards

Arci

[SPF]

Thanks, Arcibald

Having seen some progress, now I want to make sure that every step I take is the right one. Should I choose Boot without update from the upgarde screen?

Thanks
Stephen

[arcibald]

No better to reformat DOM and after ... Update with official Opensat Firmware (ex. 0.9.5020) ...

Then you can try to install your version enigma2 ...

But I recommend to everyone ... Do not enable hardware acceleration!

Regards

Arci

[SPF]

Thanks, Arcibald

This is the result when I tried to change the clock:

YAMON> setxenv -b x.pll3 0xx01020057
Not a valid numeric string (0xx01020057)
Error : Illegal syntax
Syntax :
setxenv [-b] [<key> [<value>]]
YAMON>

[arcibald]

Thanks, Arcibald

This is the result when I tried to change the clock:

YAMON> setxenv -b x.pll3 0xx01020057
Not a valid numeric string (0xx01020057)
Error : Illegal syntax
Syntax :
setxenv [-b] [<key> [<value>]]
YAMON>

Sorry ... try so

setxenv -b x.pll3 0x01020057

Regards

Arci

[shklifo]

Thanks, shklifo

Here is the log when left to run:

Setting <PB timing1> to 0x00110101.
Setting <PB Use timing1> to 0x000003f3.
Setting <PB timing2> to 0x105f1010.
Setting <PB Use timing2> to 0x000003f8.
PB cs config: 0x000e0040 (use 0x000e0040)
Enabled Devices: 0x00021ace
BM/IDE PCIHost Ethernet I2CM I2CS USB PCIDev2 PCIDev3 SCARD
MAC: 0014:15:4e:79
.......
===> [3] File system checking...
check hda
check hdb
Cannot find HDD
===> [4] Make device files
mknod: /dev/mum0: File exists
mknod: /dev/em8xxx0: File exists
===> [5] Export hostname
hostname: /etc/hostname: No such file or directory
Starting network...
ifup: /etc/network/interfaces: No such file or directory
===> Starting services...
===> [1] telnetd starting...
===> Starting MMP custom setting...

....
Stephen

Yes Srephen, all is ok, you just have DOM (hda) corrupted, but flash is ok.
If you would know the storage of azbox is here explained.

For DOM just hoping that is no harware problem.
To find out just install from the menu of usb stick a official firmware.

[SPF]

Arci

That command seemed to be accepted in Yamon.

Shklifo

Is it significant that it does not scroll past 'check hda' until I press Ctrl+C to copy the log?

When I insert a flash drive into the front or rear USB port , 'Please insert USB storage' is displayed on the TV.

What exactly do I need to do to the DOM?

Thanks, especially for spending time on this on a Saturday night!

[shklifo]

For the DOM, if it is not a hardware problem, you can resolve it by installing a official firmware, but as i see you got the problem with usb sticks? Have you formatted them before in fat32 and with patch.bin on the root of the usb stick?
Do you get the update menu to process with a firmware update?

[SPF]

Shklifo

When I insert a flash drive into the front or rear USB port and select upgrade 1. USB, 'Please insert USB storage' is displayed on the TV.

When I select upgrade 2. Network, 'Not supported yet Press any key to retrun main menu' is displayed on the TV.

When I select upgrade 3. OTA, 'Not supported yet Press any key to retrun main menu' is displayed on the TV.

When I select upgrade 5. Boot without update, the box displays 'Starting' but just seems to hang until rebooted.

I have not tried upgrade 4. Format application area.

I have been using the same flash drives that have always been successful in upgrading firmware up until now. These are formatted in fat32. I have tried to load azbox-0.9.5020-patch.bin after renaming the file as patch.bin

The logs seem to suggest to me that the USB ports are active yet they do not seem to work. I notice that it does not seem to find my HDD either.

Does any of this help?

[shklifo]

The option 2 and 3 isn't working (internet and OTA).
The 4-th option just cancel anything from DOM
The update by option 1 is strange. From the log i can see that the usb modules are Ok and insert, that let me think that usb stick isn't working proprely. Do you have another one to try?
For HDD the log is saying that nor DOM or intenal HDD (hdb1) isn't recognize.
So, can you atach 2 usb stich or 1 usb and a external HD tpo both of usb ports and bring here the last 50 lines of log? What happend when you let the log scorring, do you get a commans prompt?

[jamesjay]

Shklifo

When I insert a flash drive into the front or rear USB port and select upgrade 1. USB, 'Please insert USB storage' is displayed on the TV.

When I select upgrade 2. Network, 'Not supported yet Press any key to retrun main menu' is displayed on the TV.

When I select upgrade 3. OTA, 'Not supported yet Press any key to retrun main menu' is displayed on the TV.

When I select upgrade 5. Boot without update, the box displays 'Starting' but just seems to hang until rebooted.

I have not tried upgrade 4. Format application area.

I have been using the same flash drives that have always been successful in upgrading firmware up until now. These are formatted in fat32. I have tried to load azbox-0.9.5020-patch.bin after renaming the file as patch.bin

The logs seem to suggest to me that the USB ports are active yet they do not seem to work. I notice that it does not seem to find my HDD either.

Does any of this help?

Hi SPF,

I had a problem at this point too, I loaded an older version of firmware 0.9.4219 you should be able to get it from here h**p://fw.azupd.nl/ not a live link, and I also formatted the USB stick fat32 before using it...I changed the name to just patch after putting it on the stick, after that firmware loaded and I was able to go to 0.9.5020

Hope this helps

James.

[SPF]

I have reformatted another flash drive in fat32 and copied the Opensat patch.bin file to it. I have inserted a USB flash drive into both ports and rebooted. When I let Yamon scroll without pressing Ctrl+C to break it gives the following log but again only goes past hda when I press Ctrl+C. I don't understand why it does this!

Execute final at 0x91200000 ..



********************************* *
* YAMON ROM Monitor
* Revision 02.06-SIGMADESIGNS-01-2.8.0.1
********************************* *
Memory: code: 0x11000000-0x11040000, 0x11200000-0x11204000
reserved data: 0x11240000-0x12440000, PCI memory: 0x12440000-0x128 40000
Environment variable 'start' exists. After 1 seconds
it will be interpreted as a YAMON command and executed.
Press Ctrl-C (or do BREAK) to bypass this.

xrpc succeeded
Checking zboot signature.. it's a zboot file, signature OK.
Decompressing to 0x90020000 ..
Output length: 0x0096843a(9864250)
load compressed zboot file from 0xb3000000 to 0x90020000 OK
Linux version 2.6.15-sigma (kevin@kevin-laptop) (gcc version 3.4.2 ) #138 PREEMPT Thu Jan 22 21:35:07 KST 2009
Configured for SMP863x (revision ES6/RevA), detected SMP8634 (revi sion ES9/RevC).
SMP863x/SMP865x Enabled Devices under Linux/XENV 0x48000000 = 0x00 021ace
BM/IDE PCIHost Ethernet I2CM I2CS USB PCIDev2 PCIDev3 SCARD
Valid MEMCFG found at 0x10000fc0.
CPU revision is: 00019069
Determined physical RAM map:
memory: 02fe0000 @ 10020000 (usable)
User-defined physical RAM map:
memory: 06ae0000 @ 10020000 (usable)
On node 0 totalpages: 92928
DMA zone: 92928 pages, LIFO batch:31
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 0 pages, LIFO batch:0
HighMem zone: 0 pages, LIFO batch:0
Built 1 zonelists
Kernel command line: mem=107m console=ttyS0,115200
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 2048 (order: 11, 32768 bytes)
Using 150.188 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 96256k/109440k available (4425k kernel code, 13156k reserv ed, 1007k data, 4200k init, 0k highmem)
Calibrating delay loop... 296.96 BogoMIPS (lpj=148480)
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
NET: Registered protocol family 16
tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x 08000000.
PCI: Initializing SMP863x/SMP865x PCI host controller
PCI: Remapped PCI I/O space 0x58000000 to 0xc8020000, size 64 kB
PCI: Remapped PCI config space 0x50000000 to 0xc8004000, size 10 k B
PCI: device 1 disabled
PCI: device 4 disabled
PCI: Configured SMP863x/SMP865x as PCI slave with 128MB PCI memory
PCI: Region size is 16384KB
PCI: Map DMA memory 0x10020000-0x16b00000 for PCI at 0x11000000
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
tangox frequency scaling module installed.
Created /proc/cpucache_info entry.
NTFS driver 2.1.25 [Flags: R/W DEBUG].
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
SGI XFS with no debug enabled
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_marg in=60 sec (nowayout= 0)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing d isabled
serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
loop: loaded (max 8 devices)
nbd: registered device at major 43
tango2_enet: ethernet driver for SMP863x internal mac
tango2_enet: detected phy at address 0x01
tango2_enet: mac address 0014:15:4e:79
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: SMP863x/SMP865x Bus Mastering IDE controller
Probing IDE interface ide0...
physmap flash device CS2: 800000 at 48000000
CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code broke nness.
Using physmap partition definition
Adding partition #1-#5
Creating 5 MTD partitions on "CS2: Physically mapped flash":
0x00000000-0x00020000 : "CS2-Part1"
0x00020000-0x00040000 : "CS2-Part2"
0x00040000-0x00080000 : "CS2-Part3"
0x00080000-0x00700000 : "CS2-Part4"
0x00700000-0x00800000 : "CS2-Part5"
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon No v 07 13:30:21 2005 UTC).
usbcore: registered new driver snd-usb-audio
ALSA device list:
No soundcards found.
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 4200k freed
mount: /etc/mtab: No such file or directory
Initializing random number generator... done.
===> Starting system configuration...
===> [0] replace busybox 1.15.2(udh***, ftpget, ftpput)
===> [1] VFD initializing...
[TD210] INITIALIZED END
[TD210] SLEEP MODE OFF
===> [2] USB 2.0 driver loading...
Using /lib/modules/2.6.15-sigma/kernel/drivers/usb/host/uhci-hcd.k o
USB Universal Host Controller Interface driver v2.3
PCI: Enabling device 0000:00:02.0 (0000 -> 0001)
uhci_hcd 0000:00:02.0: UHCI Host Controller
uhci_hcd 0000:00:02.0: HCRESET not completed yet!
uhci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:02.0: irq 22, io base 0x58000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Enabling device 0000:00:02.1 (0000 -> 0001)
uhci_hcd 0000:00:02.1: UHCI Host Controller
uhci_hcd 0000:00:02.1: HCRESET not completed yet!
uhci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:02.1: irq 22, io base 0x58000020
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Using /lib/modules/2.6.15-sigma/kernel/drivers/usb/host/ehci-hcd.k o
PCI: Enabling device 0000:00:02.2 (0000 -> 0002)
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: irq 22, io mem 0x60008000
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2 004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
===> [3] File system checking...
check hda
check hdb
Cannot find HDD
===> [4] Make device files
mknod: /dev/mum0: File exists
mknod: /dev/em8xxx0: File exists
===> [5] Export hostname
hostname: /etc/hostname: No such file or directory
Starting network...
ifup: /etc/network/interfaces: No such file or directory
===> Starting services...
===> [1] telnetd starting...
===> Starting MMP custom setting...

(none) login: llad: module license 'LGPL' taints kernel.
em8xxx [/DATA/Yellow/Working/SigmaDesign8634/SMP8634-2805/mrua_SMP8634_2.8.0.5_GCC4_facspro d_legacy_dev.mips.nodts/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1346] init_module: begun
em8xxx0 [/DATA/Yellow/Working/SigmaDesign8634/SMP8634-2805/mrua_SMP8634_2.8.0.5_GCC4_facspro d_legacy_dev.mips.nodts/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1228] identify: board as unknown subid
em8xxx [/DATA/Yellow/Working/SigmaDesign8634/SMP8634-2805/mrua_SMP8634_2.8.0.5_GCC4_facspro d_legacy_dev.mips.nodts/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1332] identify: device 0x8634 0x86 accepted with software tango2revA
mumk_register_tasklet: (0) tasklet c8099000 status @c8d594b4
em8xxx [/DATA/Yellow/Working/SigmaDesign8634/SMP8634-2805/mrua_SMP8634_2.8.0.5_GCC4_facspro d_legacy_dev.mips.nodts/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1464] init_module: done. Found 1 em8xxx

Onthe next line after 'Found 1 em8xxx' a green rectangular curser appears.

Thanks
Stephen

[SPF]

Does anyone know why the log shows that it is detecting 4 USB ports when there are only 2? And they don't seem to be active!

[richy18]

Sorry, but i would like to recall my topic:

https://www.satpimps.co.uk/showpost....postcount=2374

It's not exiting but it is important to me.

Thanks in advance

[Smudger]

Sorry, but i would like to recall my topic:

https://www.satpimps.co.uk/showpost....postcount=2374

It's not exiting but it is important to me.

Thanks in advance

Have a search of this thread.

I know internal is not is not working yet but I sure I read some solution for external reader.

[The_Ripper]

@SPF
Your problem is that linux kernel doesnt see DOM, from your log

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: SMP863x/SMP865x Bus Mastering IDE controller
Probing IDE interface ide0...

and nothing, some standard log message from linux kernel when he see DOM

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: SMP86xx Bus Mastering IDE controller
Probing IDE interface ide0...
hda: DMS55610V010, ATA DISK drive
hda: no 80 conductors cable, falling back to lower udma mode
hda: selected mode 0x42
hda: set to Ultra DMA mode 2
ide0: DMA enabled for ATA DISK hda
ide0 at 0x223c0-0x223c7,0x22398 on irq 26
hda: max request size: 128KiB
hda: 501760 sectors (256 MB) w/1KiB Cache, CHS=980/16/32, UDMA(33)
 hda: hda1 hda2

It seems you have some DOM problems

[SPF]

@The_Ripper

Does this mean that I need to repair or replace the kernel or repair or replace the DOM?

Thanks for your help
Stephen

[The_Ripper]

Hi, this

repair or replace the DOM?