Enigma 2 by The_ripper - TEST -

[@telesat]

Recovery procedure
__________________


* For all people which have a problem with fleshing Enigma 2 in AzBox , where installation stop ~58% and now have a BOOTING message on display.

You will need :

- Application Acronis True Image

- E2Backup.tib

- External HDD case with IDE controller ( or if You are working on PC, Motherboard which have IDE controller ) .

Take the DOM from AzBox and connect it with IDE connector from Your external usb case for HDD .

Connect the red wire from power cable ( 4-pin Molex connector ) from case ( +5V ) ( picture: Molex and pwrcom ) with right oriented pin on connector which is on DOM - pictures DOM1 and DOM2

Connect USB cable from the HDD case with Your PC.

Now, startup Acronis True Image application, and choose Recovery from the menu on right side - picture 1

Choose Disk Recovery on the top of the window and load file E2Backup.tib and press next - picture 2

Choose Recover whole disk and partition and press next - picture 3

Check-all whole Disk, so it means two partitions : Ex** and Linux Swap and press next - picture 4

Choose on which disk You will restore content, in our case DOM, and press next - picture 5

Commit with OK - picture 6

Choose Proceed - picture 7

Wait for few minutes that process complete - picture 8

When the restore of data and partitions finish, press Ok - picture 9

now You can exit from application, 'Safely' eject Your external USB HDD, in our case DOM.

Disconnect usb cable, and put back the DOM on AzBox, turn on AzBox and wait for 20 seconds that E2 boot.

Now you can take a look on enigma, and when You decide to go back on Official version of Firmware, that You can do with plugin from DDdamir.

Installation od DDamir plugin is described in another tutorial.



hxxp://rapidshare.com/files/407099608/Recovery.rar.html

rgs,

[Dig Deep]

Nice, clear and well done !

[hfmls]

Carp95 i read in nabilo forum you saying that u talked to coders and tunner audio/video is ok now.

Can u tell us more?

[single]

Looks like hardware (modules) are on the way, then can someone do a update to me here?

What hardware is missing?

Tk's.

[Carp95]

Carp95 i read in nabilo forum you saying that u talked to coders and tunner audio/video is ok now.

Can u tell us more?

Please qoute my message the right way!!

There's nothing there about talking to the coders.

[fredda88]

Nope, just insiders!

Had a "chat" with some "insiders" in E2 project for Azbox HD last night.

Seems much work is already done ( yes tuner drivers are already rewritten also audio and video).

Seems the hole thing is goona be throuly open-source ( whitin short time).

[hfmls]

ok, sorry for misunderstanding .... can u explain what u mean with insiders, and can u tell us more?

[tonybam]

Recovery procedure
__________________


* For all people which have a problem with fleshing Enigma 2 in AzBox , where installation stop ~58% and now have a BOOTING message on display.

You will need :

- Application Acronis True Image

- E2Backup.tib

- External HDD case with IDE controller ( or if You are working on PC, Motherboard which have IDE controller ) .

Take the DOM from AzBox and connect it with IDE connector from Your external usb case for HDD .

Connect the red wire from power cable ( 4-pin Molex connector ) from case ( +5V ) ( picture: Molex and pwrcom ) with right oriented pin on connector which is on DOM - pictures DOM1 and DOM2

Connect USB cable from the HDD case with Your PC.

Now, startup Acronis True Image application, and choose Recovery from the menu on right side - picture 1

Choose Disk Recovery on the top of the window and load file E2Backup.tib and press next - picture 2

Choose Recover whole disk and partition and press next - picture 3

Check-all whole Disk, so it means two partitions : Ex** and Linux Swap and press next - picture 4

Choose on which disk You will restore content, in our case DOM, and press next - picture 5

Commit with OK - picture 6

Choose Proceed - picture 7

Wait for few minutes that process complete - picture 8

When the restore of data and partitions finish, press Ok - picture 9

now You can exit from application, 'Safely' eject Your external USB HDD, in our case DOM.

Disconnect usb cable, and put back the DOM on AzBox, turn on AzBox and wait for 20 seconds that E2 boot.

Now you can take a look on enigma, and when You decide to go back on Official version of Firmware, that You can do with plugin from DDdamir.

Installation od DDamir plugin is described in another tutorial.



hxxp://rapidshare.com/files/407099608/Recovery.rar.html

rgs,

Thanx for extrem effort to help others I have done followinf your instruction using PC motherboard IDE socket and it recovery was succeful but still nightmare booting exist.
in mycase the problem start when i run update to recover the original can you please uplaod recover of ooriginal Firmware it might solve the problem Thanks in advance.

[pascha99]

Tuner driver?
Have a look one the E2 drivers for the DNBU24511IST-NIM ,used in
Opti*** 9500.
It uses demodulator STV0903B, STV6110A

_hxxp://gitorious.net/open-duckbox-project-sh4/tdt/trees/master/tdt/cvs/driver/frontends

The tuner of the premium+ should be compatible in electrical design.
The last number of part numbering describes only what mechanical
type it is.See uploaded manual,side 13.
24511 is : vertical
24512 is : horizontal
24513 is : not described,but also horizontal with changed if-input
position.

The Opti*** is also produced with other frontends.
An ICC-Version you can buy,but no drivers yet.



Here an overview(not complete),of azbox tuners(dvb-frontends)

DVB-S2
DNBU24512ICC Elite/Premium / Connexant?
DNBU24513IST Premium+ /demodulator STV0903B, STV6110A

DVB-T
DNOD44QZH Elite/Premium

DVB-C
DNQS44CPP Premium+

ISDB-T
Brasil?

all frontends came from samsung.

[aoryx]

sweeet :woot-035:
this going faster than i thought
too many thanks for those who r making this dream finally comes true:cheers2:

:respect-023:

[single]

Tuner driver?
Have a look one the E2 drivers for the DNBU24511IST-NIM ,used in
Opti*** 9500.
It uses demodulator STV0903B, STV6110A

_hxxp://gitorious.net/open-duckbox-project-sh4/tdt/trees/master/tdt/cvs/driver/frontends

The tuner of the premium+ should be compatible in electrical design.
The last number of part numbering describes only what mechanical
type it is.See uploaded manual,side 13.
24511 is : vertical
24512 is : horizontal
24513 is : not described,but also horizontal with changed if-input
position.

The Opti*** is also produced with other frontends.
An ICC-Version you can buy,but no drivers yet.



Here an overview(not complete),of azbox tuners(dvb-frontends)

DVB-S2
DNBU24512ICC Elite/Premium / Connexant?
DNBU24513IST Premium+ /demodulator STV0903B, STV6110A

DVB-T
DNOD44QZH Elite/Premium

DVB-C
DNQS44CPP Premium+

ISDB-T
Brasil?

all frontends came from samsung.

Hi, just see op..9000/9500 use sh4 sti processor "stmdvb.ko".

Thanks anyway...

Can someone now's what Tuner is used on:
DNBU24512ICC Elite/Premium / Connexant? "CX24116"???

Tk's

:respect-023:

"are processor talking with standard api linux" - Without that "LOL"...


EDIT:

Ok Get it:

DVB-S2(QPSK)NIM24CC,CONEXNT CX24116&24118(CX24128)

CX24128 - Digital Satellite Dual Tuner RF IC - Conexant Systems, Inc

[hfmls]

yeah ....without that...shot in the foot

[pe.tardo]

...

Now you can take a look on enigma, and when You decide to go back on Official version of Firmware, that You can do with plugin from DDdamir.

Installation od DDamir plugin is described in another tutorial.

...

Where can I find DDdamir Plugin & Tutorial?
Thx

(Thx, @telesat for your tuto)

[buyukbang]

Is there any way to get a dual (even multi) boot azbox that's pointing to DOM or internal HDD?

This provides both a way for running opensat firmware + E2 and also enable the box using different opensat firmwares:

Example:
Boot Selection 1: E2 for TV
Boot Selection 2: Latest firmware with EPG fixes for TV (as an alternative for TV)
Boot Selection 3: An old firmware without DTS sount drop problem for multimedia playback

[4@@@@]

I think that we have to get u-boot running to manage this. Take a look at the sh4 ufs910 projects.
The u-boot must be placed at a unused part ot the ram.It also has to compiled with fs support and maye remote contorl support.
It exists also a bootmgr - but I haven't looked at it yet.

[andriorn]

Recovery procedure
__________________


* For all people which have a problem with fleshing Enigma 2 in AzBox , where installation stop ~58% and now have a BOOTING message on display.

You will need :

- Application Acronis True Image

- E2Backup.tib

- External HDD case with IDE controller ( or if You are working on PC, Motherboard which have IDE controller ) .

Take the DOM from AzBox and connect it with IDE connector from Your external usb case for HDD .

Connect the red wire from power cable ( 4-pin Molex connector ) from case ( +5V ) ( picture: Molex and pwrcom ) with right oriented pin on connector which is on DOM - pictures DOM1 and DOM2

Connect USB cable from the HDD case with Your PC.

Now, startup Acronis True Image application, and choose Recovery from the menu on right side - picture 1

Choose Disk Recovery on the top of the window and load file E2Backup.tib and press next - picture 2

Choose Recover whole disk and partition and press next - picture 3

Check-all whole Disk, so it means two partitions : Ex** and Linux Swap and press next - picture 4

Choose on which disk You will restore content, in our case DOM, and press next - picture 5

Commit with OK - picture 6

Choose Proceed - picture 7

Wait for few minutes that process complete - picture 8

When the restore of data and partitions finish, press Ok - picture 9

now You can exit from application, 'Safely' eject Your external USB HDD, in our case DOM.

Disconnect usb cable, and put back the DOM on AzBox, turn on AzBox and wait for 20 seconds that E2 boot.

Now you can take a look on enigma, and when You decide to go back on Official version of Firmware, that You can do with plugin from DDdamir.

Installation od DDamir plugin is described in another tutorial.



hxxp://rapidshare.com/files/407099608/Recovery.rar.html

rgs,

Have done this twice now and no luck still just booting! followed the instruction to the letter and it always told me opiration successful but still my box just showing booting on display any suggestions?

[digihoe]

Have done this twice now and no luck still just booting! followed the instruction to the letter and it always told me opiration successful but still my box just showing booting on display any suggestions?

I think you need to get the serial interface and do the procedure that has been explianed in this thread before. You might have another type of problem then the one described (54%).

Best regards!

[llcon]

the recovery to old fw..for all azboxes same=? i mean for plus also same? :S

[PsiDOC]

Am I correct in thinking that an image of a DOM with the original firmware loaded to the corrupted Azbox's DOM will get people out of trouble?

Psi

[tonybam]

Am I correct in thinking that an image of a DOM with the original firmware loaded to the corrupted Azbox's DOM will get people out of trouble?

Psi

Hi
May be you are correct but usually when box started Booting then checking and loading so when it stuck in booting most probably the problem is in flash and need to use ttl serila interdace.