ok its working now, with your instructions
Thanks
ok its working now, with your instructions
Thanks
But remember it is just a start. There must be some change made to get the stuff working like the one from The_Ripper. But it is a way to get it working.
One question, are you working in this server with the coloboration of the The_ripper and co?Originally Posted by 4@@@@
you guys are the best
i'm really happy all good users/programmers are coming together.
i just can't wait for the "boom" that svn will bring
@moicas3004: I offered him but at the moment I'm nearly the only one. But I wanted a git server for other projects.
One of the advantages of git is that it can be cloned very easy - no problem for me if it will be on another server.
We'll see what happens in the next few days.
Last edited by 4@@@@; 17-07-2010 at 07:48 PM.
it would be good a word from the developers, givin us a feedback how the work is.
TONYBAM, do you recovery your box , and how ?
in progress I got nokia KU-42 with 3 wire only i connect to RX GND TX and with putty i connected and got
the following information
وxosPe0 serial#cf9f27d02f2f8cbe8fb8e5d313 c5b853 subid 0x50
xenv cs2 ok
�ـ�xosPe0 serial#cf9f27d02f2f8cbe8fb8e5d313 c5b853 subid 0x50
xenv cs2 ok
power supply: ok
dram0 ok (8)
dram1 ok (9)
zboot (0) ok
>
********************************* *****
* SMP863x zboot start ...
* Version: 2.4.0-2.8.0.1
* Started at 0x91000000.
* Configurations (chip revision: 6):
* Use 8KB DRAM as stack.
* Support XLoad format.
* Enabled BIST mode.
* Enabled memory test mode.
* Use internal memory for stage0/1.
********************************* *****
Boot from flash (0x48000000) mapped to 0x8c000000.
Found XENV block at 0x8c000000.
CPU clock frequency: 300.37MHz.
System clock frequency: 200.25MHz.
DRAM0 dunit_cfg/delay0_ctrl (0xf34111ba/0x000a7876).
DRAM1 dunit_cfg/delay0_ctrl (0xf34111ba/0x000a7676).
Using UART port 0 as console.
Board ID.: "852-E2"
Chip Revision: 0x8634:0x86 .. Matched.
Setting up H/W from XENV block at 0x8c000000.
Setting <SYSCLK avclk_mux> to 0x00000000.
Setting <SYSCLK hostclk_mux> to 0x00000100.
Setting <IRQ rise edge trigger lo> to 0xff28ca00.
Setting <IRQ fall edge trigger lo> to 0x0000c000.
Setting <IRQ rise edge trigger hi> to 0x0000009f.
Setting <IRQ fall edge trigger hi> to 0x00000000.
Setting <IRQ GPIO map> to 0x20090820.
Setting <PB default timing> to 0x10101010.
Setting <PB timing0> to 0x10101010.
Setting <PB Use timing0> to 0x000003f4.
Setting <PB timing1> to 0x00110101.
Setting <PB Use timing1> to 0x000003f3.
Setting <PB timing2> to 0x105f1010.
Setting <PB Use timing2> to 0x000003f8.
PB cs config: 0x000e0040 (use 0x000e0040)
Enabled Devices: 0x00021ace
BM/IDE PCIHost Ethernet I2CM I2CS USB PCIDev2 PCIDev3 SCARD
MAC: 0014:15:d1:83
PCI IRQ routing:
IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
IDSEL 3: INTA(#15) INTB(#15) INTC(#15) INTD(#15)
Smartcard pin assignments:
OFF pin = 0
5V pin = 1
CMD pin = 2
Setting up Clean Divider 2 to 96000000Hz.
Setting up Clean Divider 4 to 33333333Hz.
Setting up Clean Divider 5 to 25000000Hz.
Setting up Clean Divider 6 to 20000000Hz.
Setting up Clean Divider 7 to 20000000Hz.
GPIO dir/data = 0x76000038/0x76000000
UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
UART1 GPIO mode/dir/data = 0x6e/0x00/0x00
XENV block processing completed.
Found existing memcfg: DRAM0(0x08000000), DRAM1(0x08000000)
Heap/Temp/Temp1/Dest start at 0x14000000/0x16000000/0x15000000/0x12000000.
Default boot index: 0
Scanning ROMFS image at 0x8c040000 (0x48040000) .. Found.
ROMFS found at 0x8c040000, Volume name = YAMON_XRPC
Found 1 file(s) to be processed in ROMFS.
Processing xrpc_xload_yamon_ES4_prod.bin (start: 0x8c040090, size: 0x0002fe84)
Checking zboot file signature .. Not found.
Trying xrpc_xload format .. OK
Checking zboot file signature at 0x13000000 .. OK
Decompressing to 0x91200000 .. OK (453328/0x6ead0).
Load time total 173/255 msec.
Execute final at 0x91200000 ..
********************************* *
* YAMON ROM Monitor
* Revision 02.06-SIGMADESIGNS-01-2.8.0.1
********************************* *
Memory: code: 0x11000000-0x11040000, 0x11200000-0x11204000
reserved data: 0x11240000-0x12440000, PCI memory: 0x12440000-0x12840000
Environment variable 'start' exists. After 1 seconds
it will be interpreted as a YAMON command and executed.
Press Ctrl-C (or do BREAK) to bypass this.
xrpc failed (9)--- if a xtask is using a cipher or if you reboot
--- xrpc will fail with RM_BUSY
Checking zboot signature.. it's not zboot file.
Error : Internal, code = ffffffff
YAMON>
the problem i have i cannot write coomand in putty
for net initialization and IP for box i keeping try till I success
I wait telesat new file with old kernel and I will try again.
I had the same problem with Windows, using Linux solved it. Also make sure that TX is connected properly.
Good, nice to hear it
Can you tell us what is missing on modulos?
Fantastic work @pascha99, thanks :respect-013:
:respect-067:
EDIT: I add some notes to your quote, for personal use I hope you don't mind, thanks.
Last edited by single; 19-07-2010 at 04:57 PM.
@The_Ripper
I sent you a link in pm with an interesting discussion
I hope it is useful
edit: I'm sorry but I did not realize that it had sufficient msgs to send pm
I sent PM on e2az
Last edited by gheos; 20-07-2010 at 01:24 AM.
Are that forum the dev forum?
:sifone:
Help trouble with Enigma2...azbox keep booting
I installed Enigma2 yesterday & get stuck,wanted to go back to Azbox fw (tried old & new version) but the box don't recognize it ...
I connected trough Filezilla and I made the biggest mistake ever...I deleted some files thinking that was related to Enigma2 files...now the box doesn't respond it stuck at "BOOTING".
I've been looking everywhere how to reinstall fw but no luck...
-I unplugged power cable for few hours,tried differents fw,tried emergency flash...but nothing it keeps booting ...
indeed , big problem.
It as already sayd here, guys that dont have big know how in linux don't install this first image. ITS ON THE FIRTS POST.
Now you have to get a serial cable with RS232 to conect the box or folow the procedure that is on this post a few pages back, removing your DOM from the box and do as it says.
Dear friends, as we got many inquires on PM about that user hfmls spreading rumors about some release dates, and current progress on this project, We want to say that we are not speaking with him, and we dont know from which persons he is getting this informations, but absolutly NOT from us. Also we dont know what is the reason for that, like he is telling dates when something should be released, maybe to rise up his popularity or ?
Point of this post is not to insult anybody or to discredit anybody , just precaution that in future everybody of You know, that this guy is not representing our work, opinnion or any news, and as I mentioned before, all work will be published public, so nobody needs any kind of rumor.
Last edited by MickeySa; 20-07-2010 at 04:50 PM.
trash discard or send a guarantee.
Thanks very encouraging...
trash discard or send a guarantee.
I see that you get the answer from the expert - clear and fast solution
but don't worry, you have an answer in this forum - how to ...
Regards expert : if you don't want to help - don't lie to people.
rgs,
Posting Permissions
Reply With Quote
Bookmarks