Enigma 2 by The_ripper - TEST -

[ircihumax]

I have not tested but the solution neutrino keymap will be close to the your expectations.

here's the link

https://www.satpimps.co.uk/showthread.php?t=141557

stupid question, could i map things to get keymap like kathrein enigma2 and azbox hd original firmware?

OK to show channel list, up and down zapping and right left volume change.
infobar in info button.
epg in guide, etc.

i really prefer this method

[Smudger]

I have a Azbox elite dual tuner (SAT + DTT)
Fw .27 installed, enabled multiple bouquet from the menu.
Configured the tuner as USALS and enter my coordinates.
Installed list Vhannibal MOTOR(October 23) by enigmEdit through in enigma 2.4 mode(then reloaded settings). The list is displayed correctly.
Unfortunately I can not see the FTA channels.
And the error that you read about these channels is as follows:
"No data on transponder"
If i connect or disconnect sat cable to azbox, I always have signal SNR 99% and BER: -22 on all channels, FTA and encrypted.
Does anyone have any idea what can I do?
Is for a week that are blocked on this issue. I've never seen anything with enigma 2, with none of the versions.
Let me know.
Thank you very much.

PS: The scans work but can not find any channels.The decoder is fully working with official firmware(opensat)

I have the same problem except I have a single SAT tuner Premium hardisk fitted and using a twin LNB.
my reciever is about 18 months old so has the original board and not the later one. Can someone confirm an older reciever working?

[DimitarCC]

You can also use the NOKIA TTL / RS232 DKU5 or USB CA-42 data cable ...









Here more info:

http://buffalo.nas-central.org/index.php/Use_a_Nokia_Serial_Cable_on_an_ARM9_Linkstation

http://pinouts.ru/CellularPhonesCables/nokia_dku-5_cable_pinout.shtml

or build the interface RS232/TTL (these schemes):


Regards

Arci

Thanks man! I will try that later! I hope i can revive my box or i will trash it! too many trouble with that box!

[Fatum]

I have the same problem except I have a single SAT tuner.
my reciever is about 18 months old so has the original board and not the later one. Can someone confirm an older reciever working?

I also have older reciever. This same issue SNR 99%, BER -22. Single tuner, USALS. Positioner menu = green screen :(

[kanber_kav]

I also have older reciever. This same issue SNR 99%, BER -22. Single tuner, USALS. Positioner menu = green screen :(

Telnet command
dmesg message
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
root@AZBox:~#

azbox shutdown and wait 1-2 minutes and lan cabel inset and open ..

[Smudger]

Telnet command
dmesg message
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
root@AZBox:~#

azbox shutdown and wait 1-2 minutes and lan cabel inset and open ..

I do see the about.

Is the shutdown a power off or standby?
lan cable inserted and open ? no sure what is meant by that.
I do apprciate english is not your native language.


i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x1f (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x1f (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x1f (error=-22)
cx24116_cmd_execute() Firmware not responding
CX polarity/voltage = 2
CX polarity/voltage = 2
Wrong ACK(0x10)
Wrong ACK(0x10)
DVB: audio0 Open the pools
DVB: audio0 dmapool id = 0
DVB: audio0 Open the pools
DVB: audio0 dmapool id = 0
DVB: audio0 Open the pools
DVB: audio0 dmapool id = 0

after shutting box off for 2 mins and restarting I know get

cx24116_readreg: reg=0x1f (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x1f (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x1f (error=-22)
cx24116_cmd_execute() Firmware not responding
CX polarity/voltage = 2
CX polarity/voltage = 2
Command Fail
Checksum Error
Checksum Error
DVB: audio0 Open the pools
DVB: audio0 dmapool id = 0
DVB: audio0 Open the pools
DVB: audio0 dmapool id = 0
DVB: audio0 Open the pools
DVB: audio0 dmapool id = 0

now with a channel list and channel selected I get

cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)

[BE-COOL]

I confirm that with the DVB-T tuner unplugged, the DVB-S2 is working now.

[The_Ripper]

@Smudger @kanber_kav @Fatum
So it seems that some old very old Azbox receivers have some trouble with this tuner driver code or I2C protocol code , I will check this.
Can you guys open receiver and check if there is some date on PCB board ?

[kanber_kav]

my board first CI device fix board. goto home serial send forum.
(Azbox Premium) use dm800 settings.

[Smudger]

@Smudger @kanber_kav @Fatum
So it seems that some old very old Azbox receivers have some trouble with this tuner driver code or I2C protocol code , I will check this.
Can you guys open receiver and check if there is some date on PCB board ?

I have a label on PCB under sat tuner TD210SP 09 0100095 and tuner DRACO_DVB-S-S2 REV3.00

I did once get picture with 1.0.25 original tuner driver tried since but unable to recreate.

I know my board is the one which requires a ci update to use certain cams.

Premium HD

reciever s/n TD0064-092-00005

Anything else before I put lid back.

[Fatum]

@Smudger @kanber_kav @Fatum
So it seems that some old very old Azbox receivers have some trouble with this tuner driver code or I2C protocol code , I will check this.
Can you guys open receiver and check if there is some date on PCB board ?

I'll check the details as I get home.

[moonlight]

@Smudger @kanber_kav @Fatum
So it seems that some old very old Azbox receivers have some trouble with this tuner driver code or I2C protocol code , I will check this.
Can you guys open receiver and check if there is some date on PCB board ?

This Problem Have only Premium Or Premium + elite ?

[A13x]

here the same with azbox elite

DRACO_DVB-S-S2 REV3.00 TD2110S 09010198 without CI fix

[happyhammer]

Actually the only working solution is based on Wrigler JTAG adapter which is the cheapest one on the market ... and also it is very simple for DIY.

If you read carefully posts at pristavka.de - there is good explanation how to create / Wrigler adapter, and how to perform NOR flashing.

Regards!

Yes I followed those instructions and the DIY cable is really a passive DLC5 not a wiggler. So those instructions did not work for me. I will test when my adapter arrives as it can do buffered signals

[Fatum]

@The_Ripper

Details

Azbox Premium

Reciver:
TD210SP
S/N: TD0064-092-000698

Tuner:
DRACO_DVB-S2 REV3.00
DNBU24512ICC
090111 BAAATRM

Mainboard:
TD210SP
09 0200765


Smudger has little older reciver (S/N)

[Smudger]

@ The_Ripper do you think they maybe a solution or are we going to missout as we did with the CI problems.

[MickeySa]

@fatum, Smudger, Kanber_kav and all which have problem with signal.

Please test this driver.

THIS DRIVER IS JUST FOR USERS WHICH HAVE PROBLEM WITH SIGNAL



Please test and give us feedback.

Change old cx24116.ko with this new one.

Location is :

/lib/modules/2.6.22.19-19-the_ripper/extra

When asked for Overwrite, click Yes, then turn off and turn on Your receiver.

[stra]

Yes I followed those instructions and the DIY cable is really a passive DLC5 not a wiggler. So those instructions did not work for me. I will test when my adapter arrives as it can do buffered signals

First of all you have to connect to the console (with RS232 cable not DLC5 or wiggler) and see the result. It is important, because from console output you can find out how to recover your box - with serial console only or there is needed JTAG cable

Regards!

[Smudger]

@fatum, Smudger, Kanber_kav and all which have problem with signal.

Please test this driver.

THIS DRIVER IS JUST FOR USERS WHICH HAVE PROBLEM WITH SIGNAL



Please test and give us feedback.

Change old cx24116.ko with this new one.

Location is :

/lib/modules/2.6.22.19-19-the_ripper/extra

When asked for Overwrite, click Yes, then turn off and turn on Your receiver.

Still no go for me. I get the same results as before. :(

[ngiolett]

Are there news about to start e2 from usb or hdd device???