Results 1 to 6 of 6

Thread: Samsung 9500DSR EM VIA :::: Help Pleas ::::

  1. #1
    Senior Member
    Join Date
    Oct 2005
    Posts
    23
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Question Samsung 9500DSR EM VIA :::: Help Pleas ::::

    HI! To everybody
    I have a Samsung 9500DSR EM VIA that show me only
    for a few sec "9500" in the display, and after nothing else.
    I can dialog with deco ,sending firms and settings
    and i can see them with the dumps and everything
    works correct.I already changed the capacity inside
    the tuner,without results.
    I need help.
    Many thanks in advance who help me.
    I'm sorry for my English.

  2. #2
    Mildly Important Nymph :D goran's Avatar
    Join Date
    Dec 2004
    Posts
    2,225
    Thanks
    0
    Thanked 4 Times in 4 Posts

    Icon12

    Sometimes one loses the channel/settings list and that will make it "go". Simple.

    Sometimes it's more complicated.

    To put the RG EMU in you must have Loader 500 or 501 in your Sammy and then you can do it.

    Versions VIA CI, CI, FTA and EM VIA can be flashed, given the loaders I mentioned..

    If one's Loader is 505 [or if it is 500 or 501 but damaged] you must JTAG it, with a specific short cable, SW and a procedure that requires some knowledge and patience. Sometimes it just must be done many times before it's successful. Sometimes one has to change a PC to do it.

    Then you put in the RG EMU, Settings/channel list, RAM.bin and watch...

    Read my Intro, as to how to do it exactly [after you JTAGed it, if necessary].

    Good luck!

  3. #3
    V.I.P cuorino's Avatar
    Join Date
    Dec 2004
    Posts
    51
    Thanks
    0
    Thanked 0 Times in 0 Posts
    To complete Goran guide, load firmware with hyperterminal: your problem is very often to load setting instead firmware, then 9500 appears for few seconds.

    switch off on the back stb.
    Start/Program/Accessories/Communications/Hyper Terminal

    Setting the Hyper Terminal

    1. Start Hyper Terminal.
    2. In the field "Name" write for example Samsung 9500, choose an icon and click OK.
    3. In the new opened window, near "Connect using" choose "Direct to COM1 or 2 or 3, afterwards click OK.

    Port Settings

    1. Bits per second : 115200
    2. Data Bit : 8
    3. Parity : NONE
    4. Stop Bit : 1
    5. Flow Control : Hardware
    Click OK

    Uploading software into Hyper Terminal

    1. Choose TRANSFER
    2. Then choose SEND FILE ....
    3. BROWSE - select from hard drive the desired version of software (e.g. emu 7.3.bin)
    4. Choose 1KXmodem for Protocol
    Don't press the button "Send", you will do it subsequently.

    After you have done the procedure described, connect your computer with Samsung using a RS232 connection cable.
    Before you start uploading the new software into Samsung I would advise you to firstly remove all the cams or cards from it (if any are inside).

    The things you have to do are :

    1. keep pressed the "right arrow" (volume up) and the main switch on the back

    Keep pressed until the "3-01" appears on the display and appairs all CCCCCCC
    from that moment the computer will show "............................ ... Loading"
    4. In that moment, in the Hyper Terminal, click the button "Send" (you have about 15 seconds to perform that operation).
    With clicking on "Send" starts the uploading the software into Samsung.
    Don't be hasty! Wait for entire process to terminate.
    Process is terminated when on the Samsung a clock appears.

    If you have done all properly, there is a desired version of software in you Samsung.
    The easiest way to verify if upload succeeded : Menu/System properties/System information.
    All versions of the EMU software has the version number 133, to not confuse you.

  4. #4
    Senior Member
    Join Date
    Oct 2005
    Posts
    23
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Thanks m8, I have to try this.

  5. #5
    Junior Member
    Join Date
    Mar 2010
    Posts
    1
    Thanks
    0
    Thanked 0 Times in 0 Posts
    thank you cuorino so so so so so so so much my problem was fixed thnk you so much

  6. #6
    Verified Registered User
    Join Date
    Dec 2004
    Posts
    141
    Thanks
    132
    Thanked 183 Times in 54 Posts
    Thanks cuorino so much for your help, the 1KXmodem transfer works great !

    After the flashing the firmware to SamsungDSR9500_RVGOLD_V8.4, I then Powered OFF / ON at the back of the Sammy, press menu button on remote so diplay shows "MENU", then download old channel settings file using SemcoEditor204Eng.

    My Sammy is back to normal again, thanks so much guys.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •