-
modest supermod
help section
hi all,
here is/will be a repository of humax help files, it is a closed thread so requests for texts/tutorial's should be made in the main forum, if the post is made @voith i might see it, and if its in my power or i can find it, i will put it up here, or another mod might be able to supply it, also anything any mod decides to be useful will be put in here
hope they help
voith
HELP, i have lost most of my database of help stuff, any help would be grateful
Last edited by voith driver; 26-11-2006 at 03:08 PM.
-
-
modest supermod
humax error codes
hi all,
here is the humax error codes taken directly from the HCSA site
E-HC/bC Incorrect header block(CRC-16) The software seems damaged while you receive from web site or e-mail.Pls receive the software again and try to download
E-dC Incorrect data block(CRC-16) The software seems damaged while you receive from web site or e-mail.Pls receive the software again and try to download
E-Hn/bF Invalid HDF version This error can be occured when you attempt to download Non-Superset STB software to Superset or Vice-Versa.Pls check the STB model and the software
E-Id Invalid system ID This error can be occured when you attempt to download F1 software to F1-CI. Pls check the STB model and the software
E-AC Incorrect application CRC-32 Download latest version of application sw. If it doesn't make it,the flash memory can be thought to be defected
E-ut UART RX/TX time out There is communication problem between source and target
1) Check whether the S/W is compressed or not and Check whether you use the proper download tool for the software
2) Reduce the download speed and try to download again
3) STB main power Off/On and try to download again
4) Reset the PC and try to download again
E-Ad Invalid address Humax made the hdf file with wrong address.Pls notify this error to us and wait until we release the proper software.
E-Ao Invalid offset address for upload(Odd offset) There was a mistake when we made hdf file from binary file.Pls let us know immediately and wait new release version
E-Ft Flash program time out The flash memory in STB seems damaged. Pls try to download one more time. If you fail agian,send us back to replace the flash memory device
E-It/Et EEPROM program time out The EEPROM in STB seems damaged.Pls try to download one more time.If you fail again,replace the EEPROM device
E-FE Fail compare after flash write Flash memory is damaged.Return the main board(CPU Board)
E-HF Invalid HDF Format It means that the file you try to download is not a valid HDF format. The file could be damaged in which case you should try downloading it from the Humax web site again. Also please check the file extension is HDF. Also make sure you are using the correct download tool - Wdn4oak+. It can be also occurred when there is some problem on cable, data of PC and loader.
E-Fn Invalid flash device Flash memory is defected Need to change the flash memory so Pls return the Main Board
E-AS Incorrect application s Check the software version and STB hardware specification
not mentioned is
err rA with three flashing dots, this is usually solved by uploading a new channel settings file
hope it helps
voith
Last edited by voith driver; 25-11-2006 at 10:06 PM.
-
-
modest supermod
springclean (spring clean) humax 5400
hi all,
here is the txt of the springclean
the text goes like this, it is written assuming you are using thor as your 0 position or due south bird, if you are using another sat for this then substitute that sat for thor and make the amendments where needed
How to spring clean your humax 5400
For Humax 5400 Z patched
H/W oak 1&11 2.1
S/W Hic 1.05.00+
Device driver version Hic 1.05.00+
S/W last update 4 mar 2002
Loader version H 2.08
sys id 0016.0600
tuxonhumax ToH 3+
files needed.
HU 15 (on this date) uploader for HDF files
HIC 1.05.00 hdf (or relevent hdf for your model)
HIC delete all channels hdf
your saved settings file, or the latest pet123, original or my modified.
humbox 4.1 or your own favorite editor
tux on humax +cam ToH 3+ (on this date)
The idea is to put your humax 5400 back to its original out of the box state ready for the new patch,
and new settings.
WARNING
THIS WILL PUT THE STB TO ORIGINAL SOFTWARE PRE PATCH, AND ANTENNA POSITIONS TO ORIGINAL POSITIONS.
LOADING ORIGINAL SOFTWARE
first start the HU 15 uploader program
make sure the com port is correct and speed is 115200
click on the tab marked open HDF file
navigate to where your original software is and click on open, you will get checked ok message
(providing you have got your original software from humax's home site) click on ok
click on upload (pc to stb) waiting for humax connection banner will appear
turn stb to standby using your handset
now turn back on using handset
the banner will start uploading, wait until you see END appear in the panel on your stb then
turn stb on at the on button on the stb.
To check your upload press
menu
installation
status
stb status
and you will see
H/W oak 1&11 2.1
S/W Hic 1.05.00
Device driver version Hic 1.05.00
S/W last update 4 mar 2002
Loader version H 2.08
sys id 0016.0600
when you change satellites there will be a red banner
and you will only get FTA or irdeto channels.
RESET PRESTORED POSITIONS
change to a thor channel (this is not required but helps for other reasons)
menu
installation
service searching
as this is the original software you need to put in the pin 0000
manual search
ok on antenna alternative
diseqc command change to installer
up to sat name and change to reference
motor control change to goto,ok. wait for dish to alter(1deg) this is a chance to
visually check if you wish by climbing the ladder.
(also if you are lucky you may still barely get the signal from thor that you were on)
now change motor control to reset, you will get a warning all will be recalculated, press ok.
back up to sat name change back to the sat you were on, if thor intelsat 707
diseqc command change to user, ok
exit exit exit exit
Ok now everything is back to original, and now we can start getting it back together. and if your
setup is ok you will still be getting a signal on thor.
First find a spare channel on your TV, and tune it to CH 38 this is a precaution in case you lose
the picture when deleting the channels.
DELETING ALL CHANNELS.
Now this action deletes all channels but does not delete the prestored positions, hence the above.
first start the HU 15 uploader program
click on the tab marked open HDF file
navigate to where you put the delete all channels hdf and click on open, you will get file unknown message
(providing you are using the one supplied with this txt it will be ok) click on ok
click on upload (pc to stb) waiting for humax connection banner will appear
turn stb to standby using your handset
now turn back on using handset
the banner will start uploading, wait until you see END appear in the panel on your stb then
turn stb on at the on button on the stb.
there will be three (3) green dots flashing on the stb panel.
you might also at this point see a blank screen, change your TV to the channel where you tuned Ch 38
on the screen you will see a warning that no services are registered, it is not needed to press ok, (this
is only for people who wish to find there own services)
NOW TO LOAD YOUR SETTINGS FILE.
open your favorite editor, in this case Humbox 4.1
stb used humax 5400z, with nullmodem cable, program humbox 4.1 and either setting
files pet123 from www.humaxsettings.nl or my modified pet123 for h to h mounts, which i
post on this site.
download either settings file.from the web and save.
open humbox,click on edit, options.
click on model,
change model for your own, and change system id to yours, this is found on the humax
by menu,intallation,status,stb status. you cannot do this at this stage so make sure you have this
written down before you start the spring clean.
click on port tab, check the correct port is marked.
change anything else you wish
when satisfied click on ok.
now click on the menu tab.
if in England, in the uhf tuning section change pal to pal i, or whichever pal you have.
change anything else you wish.
now to download to the stb.
Go to file, open, and navigate to the new settings file, select and click on open
if you are using my modified pet123 it has most of the prestored positions input
turn your stb to standby.
click on the little dish icon (download to humax)
the waiting for connection , banner appears
turn stb on, and progress is shown on screen and tv.
HERE IS WHERE SOMETIMES IT GOES PEAR SHAPED, IF YOU SEE ERROR SYS ID, GO BACK TO THE BEGINNING AND REDO THE BIT ON OPTIONS.
when finished END will show on the stb press the standby button on the stb.
you will now need to back to the TV channel you normally use
you should now have the new channels and be able to get your antennas.
Now to check and fine tune your new setup.
You checked in passing in the beginning that thor was ok
so for a check go to a channel on thor and
menu
installation
service searching (still have to enter the pin 0000)
manual search
ok on antenna alternative
check that diseqc command mode is in user
movement press either left or right untl you have a good signal, when you have a good bottom line
signal, then go to
motor control and change to store, THEN PRESS OK
remember how much and in which direction you moved, this will be needed for all other sats
exit exit exit exit exit
now we work down the rest of the sats
ok
yellow
yellow
and work up and down the sat list
ignoring amos unless you actually use it
choose each one
ok
ok on a channel name
identify hopefully by the name on screen
then fine tune as above if needed
please read the other txt files included in the zip for more info
one thing to note,
jeager superjack dg120 owners when looking for seasat at 35.5E (if it is programmed as mine)
you will need to tune in installer mode and go all the way from 38.5W because of an hardware error.
all other sats will be on the button or very near, keeping in mind the constant noted above.
in the txt included with this will be a list describing how and why and in which direction to tune the
odd sat that does not show.
Now to patch your humax.
i would suggest you follow SHADOWS post how to patch your humax.,but it is no harder than putting
in the original software
regards
voith
Last edited by voith driver; 11-04-2008 at 08:02 PM.
-
-
modest supermod
Quick Guide to whom confused (CW , Dsr 9500 Emu 5.3, etc ..)
as posted by kokokoko
Hi m8,
Just noticed that most of members here are confused since Humax able to decode CW & publishing New DSR 9500 EMU Ed53 , new keys files , etc....
the main point here is CW keys embadded into the Humax Emu (part of the whole batch ) not into the ram editor ( Catone2.6) where we can edit & change keys .
so when u switch to one of the CW channels the Humax Emu go and call the Keys from the emu not from the ram ediotor (as no place 4 CW keys).
that is mean that we can't add,delete, edit keys from ram editor and new keys files have no conection with the emu .
to overcome this Problem we have to have the following :
1- New DSR 9500 EMU Ed53 which have places for CW keys
2- keys files with a new Format to deal with new DSR 9500 EMU Ed53
---------------------------------------------------------------------
3- New Hot-Toh ram editor (Catone2.7) to accept CW keys(manualy) & keys coming from New DSR 9500 EMU Ed53 or any other keys programs
4- New Hot-Toh Firmeware (Emu) to change the way calling Cw keys to be from ram editor not from the Emu itself .
------------------------------------------------------------------------
That is why New DSR 9500 EMU Ed53 Editor said (( Key-space Offset is changed from this version
so it can NOT be used with Older Ram-Bin/Firmware ))
Up till now we have New DSR 9500 EMU Ed53 & keys files with a new Format
Still waiting for New Hot-Toh ram editor (Catone2.7) &
New Hot-Toh Firmeware
Hope it might help
-
-
modest supermod
how to fix the psu for humax receivers..
hi all,
as posted by shadows,and modified by grumps
how to fix the psu for humax receivers..
originally posted by Grumps.....:
To those that may be interested this is a list of parts that will fix a burnt out power supply unit for a Humax IRCI5400
(Rev: 1.0 but all should be the same) and will save you a lot of money.
IT IS DANGEROUS TO PLAY WITH ANYTHING ELECTRIC IF YOU DO NOT KNOW WHAT YOU ARE DOING
only attempt this if you have some electronics experience and soldering skills.List of parts you will need: = Use 105 degree caps not 85
C09 1000uF 16v
C10 1000uF 16v
C13 1000uF 25v
C14 1000uF 25v
C15 470uF 25v
C16 470uF 25v
C17 220uF 50v
C18 220uF 50v
C19 100uF 50v
C20 100uF 50v
C21 1uF 50v
R21 100 Ohm You can use a 0.25w but I used a 0.6w
ZD3 30v Zener Diode 1.3w
As a last resort... ring 02891 824964 & ask for donald ...he`ll sort u out ...Humax N.I... ...
rgds-grumps
addendum by from coalman
ref. power supply fix posted by grumps
Hi Voith could i also suggest replacing r2 a 180k 2watt resistor at the high voltage end of the pcb it gets quite hot and over the years the soldered joint deteriorates (well it did in mine) ending in a dry joint. If you do replace it leave plenty of wire on to keep the heat away from the pcb. i also replaced zd3 30v zener & r21 100r both burnt out
here also is a diagram for the psu found by marco
Last edited by voith driver; 12-12-2006 at 11:43 PM.
-
-
modest supermod
for original 5400 software
hi all,
thanks to jaythesnake007, here is the HSCA site that carries at this time the original software for 5400
w.w.w.humaxdigital.com/deutsch
you will need to register, but it seems if you are already registered in the english hsca site this will carry across
regards
voith
-
-
modest supermod
Humax 5400 loaders - the do's and dont's of loaders.
hi all,
as suggested by siegfried, a tidy up.
Humax 5400 loaders - the do's and dont's of loaders.
Information supplied by carnage, humi-user and Siegfried.
There are 4 different loaders for the 5400, the System ID and loader version depending on the hardware in your STB:-
L1.3x = Sys ID 0016.0000 = OAK-I board with MK2 tuner
L2.0x = Sys ID 0016.0200 = OAK-II board with MK2 tuner
H1.3x = Sys ID 0016.0400 = OAK-I board with MK3 tuner
H2.0x = Sys ID 0016.0600 = OAK-II board with MK3 tuner
The latest versions are L1.37, L2.08, H1.37, and H2.08 .
The 5400Z usually has the one loader H2.08 .
It is not necessary to upload a loader to patch a receiver, but it is recommended to first return it to it's original state by uploading the official Humax firmware. If you need to reload the original Humax firmware (the latest version is HIC10500-0x.hdf) make sure that you load the correct version for your loader/sys id:-
L1.37 = ..-00.hdf
L2.08 = ..-02.hdf
H1.37 = ..-04.hdf
H2.08 = ..-06.hdf
Note that all ToH patches are independent of the loader and work with all loader versions, and do not contain a loader.
WARNING
None of these loaders is better or worse than the others and they are NOT repeat NOT interchangeable !!!
A receiver originally with an H1.37 loader would be destroyed by uploading an H2.08 loader !!!
A receiver originally with an L1.37 loader wouldn't work with an H1.37 loader !!!
Also, the H2.19 loader is only for Humax 5400Z+ STB's with the SD1278 LVA-3 tuner and Sys ID 0016.0601 . It is not compatible with the Humax 5400 or 5400Z so do NOT try to update those STB's to the H2.19 loader.
You have been WARNED.
-
-
modest supermod
PIN Reset
as posted by TNT.
PIN Reset
Turn on humax and go to [Menu > Installation > Status > STB Status] then press
Red - Green - Yellow - Blue - White - 0 (zero)
If you do it right you will see this message
" Pin code has been reset "
TNT
-
-
modest supermod
c-band and the 5400
hi all,
here as posted by harrysat
Hi, I use the Humax 5400 among others (Nokia 9500 and Echostar 3000) for C-band and it works fine.
Just choose in the Menu the right LO (local oscilator) frequency (5150 MHz) and search with the right frequency, Polarization, SR and FEC parameters, you can use the following method:
I suggest that you make a separate C-band Antena Alternative by Menu/Installation/Service Searching/ Antenna Setting, then choose the Antenna Alternative number (from 1 to 32 whatever you like and don't youse for others dishes) by right or left-clicking on the control. Then a row lower you can specify the name of this Antenna Alternative by right clicking to "User defined" and write for instance: "1,8 m C-band dish".
You can choose (for the Antenna alternative (1,8 m C-band dish) that you have chosen to receive C-band channels on) the right LO frequency by: Menu/Installation/Service Searching/ Antenna Setting/LNB frequency and change "Universal" to "5150". Look also at the right parameters when you use a 12/0V switch or Diseqc switch or motor.
You can search by: Menu/Installation/Service Searching/Advanced Search/
The PMC table does not change anything because there does not exist PMC tables with parameters for C-band channels. So if you are not satisfied with the audio preselect language or anything else, you have to change it yourself with a PMC editor.
-
-
modest supermod
how to recover from a a/v output problem
hi all,
as posted by TNT, an easy way to recover from a video output mess up
Hi
Turn your humax off then on and press Blue Button, Down Arrow, ok Twice
TNT
-
-
modest supermod
dsr 9500 and capkeys 1.3
ATTENTION, I am fairly sure this is within the rules, but please do not ban me without checking
attention, capkeys 1.3 not working at this date of posting
hi all,
ok, against my better judgement i am at it again, i have been banging on about the update facility in dsr9500 5. well, yes it works, but only if the url you/we are using carries the keys you want, other wise it all goes **** up, so here is my other method of doing it.
programs needed
dsr 9500 5.+
key capturer
first open up dsr
tick empty ram, and write this to your stb,
then go menu, toh, parser, ram editor, and just check you have no keys showing
now load the very best of bin's, (and i do not take the micky)
i am talking Mach1. RAM.bin into dsr9500 5+
now start key capturer
click on get providers
now if we are looking for tps, then in the provider list choose tps
click on capture keys, make sure you give it access to the web.
after a few seconds it will show the new keys with the date issued
in dsr9500
choose the correct provider in this case viaccess 007c00
now for line 3 its just a case of deleting the keys in that line, and copy from the key capturer, and pasting into line 3
for line 13, tick the +0x10 via 2 key box, and line 13 will show, then copy and paste as before
now its only a case of writing the keys to the stb
after this turn off by the remote, and then turn on.
please note, that you still need a recent bin loaded before you can input keys,
tps = line 3 and 13
polsat = line 8 and 9
HOT 7.5
D+ 4101
keys 00 split between lines 00 and 01
keys 01 split between lines 02 and 03
TPS 7C00
still split between lines 03 and 13
POLSAT 7101
keys 00 split between lines 00 and 01
keys 01 split between lines 02 and 03
TV CABO (KAKA)4901
keys 00 split between lines 00 and 01
keys 01 split between lines 02 and 03
MEDIAPARK 1911
key 0 line 00
key 1 line 01
hope this helps
voith
Last edited by voith driver; 04-12-2006 at 11:16 PM.
-
-
modest supermod
Humax power supply docs.
Humax power supply docs as posted by seigfreid
-
-
modest supermod
''How-to'' input and delete biss keys using the remote controll
''How-to'' input and delete biss keys using the remote controll
as posted by sat_rrstm.
and updated
''How-to'' input and delete biss keys using the remote controll
for versions from ToH3.4_HoT9.4 and later ones.
by sat_rrstm.
We usually get a biss ch. codes in this form:
NBA TV .
Index: 1FFA .
HEX key: 18 39 6D EC 81 A6 25 C0 (8 sets,16 digits)(this key is not active).
From version ToH3.4_HoT9.4 and later on,first we take the ch's frequency 11892
and turn in heximal form : 2E74
We need now the ch-ID in its heximal form.Ch-ID of NBA is 4 and turns to 0004
and we need the last byte only,04.
The last we need is its PMT PID which is 32 and turns to 0020 and we need only
the last byte,20.
So the first 8 digits of the biss key-line are : 2E74 0420
Out of the 8 key-sets we skip the 4th and the 8th ones,so here is what is left:
18 39 6D 81 A6 25,and here is the complete key-line : 2E74042018396D81A625.
When we have found DCW of a not-biss channel,like ***View or MCT channels,
it looks like this:B 36B2 00 FD6C6DD6430E68B92DAF6B47CCC2A432 :*** View PLUS(this
key is not active)
In this case we have to create two lines that have the first 8 digits similar.
These 8 digits are created in the same way as above with NBA TV and so for the
*** View PLUS they are : 3048 B292 .
Now we get the 32-digited key we found and split it in two 16-digited parts
(we cut it in the middle):
So the key FD6C6DD6430E68B92DAF6B47CCC2A432 becomes :
FD6C6D(D6)430E68(B9)
2DAF6B(47)CCC2A4(32)
Now we add the channel's 8 digits in front of each created part and we skip
the digits in the brackets and we get the two lines we need:
3048 B292 FD6C6D430E68
3048 B292 2DAF6BCCC2A4.
Using the remote we go to : Menu --> TOH --> Parser --> Ram Editor -->OK
Press P+ or P- till you see BISS-FIXED DCW screen,or press only the 'musical note'
button (for radio ch's)
Go to an empty line : 00000000000000000000>Press OK. Insert the 20 digits-->
Press OK.We exit all menus and then press STANDBY on HUMAX to store.
If we wish to delete a biss key line,first we flash it and then we press
STANDBY button on the remote instantly 4-5 times.
If we'd like to delete 2 key lines at the same time after flashing the first one
we keep pressed almost any button,except 'recall' button,for about 4-5 seconds!
Last edited by voith driver; 07-09-2007 at 10:25 PM.
-
-
modest supermod
how to use dsr9500 5.6cw
hi all,
Originally Posted by sat_rrstm
When you downloaded DSR9500_EMU_Ed56_CW,did you notice if all files that should
be in there,were there? The whole pack of this software includes the following :
1: DSR 9500 EMU Ed56_CW,the main exe
2: Editor_ReadMe,a text file
3: Microsoft_Script_Control,a zip file
4: MSINET,a zip file
5:Mswinsck,a zip file.
First you have to unzip all 3 zipped files and then,getting into the new 3 folders,
you have to install them in your PC,by double-clicking on the them and getting the
successful installation-messages.
Then you have to run the main exe and do the following settings:
button : ? --> Settings --> Humax Def --> one left click.
Now again: ? --> Settings --> Com Port --> Com Port 1 --> one left click.
Now : ? --> Settings --> FW Check --> Off --> one left click.
Last : ? --> Settings --> Verify from Box --> On --> one left click.
Now you have created a new NotePad script called ''Settings'',you can see it in
the same folder with all the rest files.
After you have checked all these,try to load the latest key bin to your DSR exe.
Turn on Humax and tune it to a FTA channel and press ''Write'' button on DSR exe.
Now you get this message:
''Do You want to write already loaded file ?''.
Answering ''Yes'' makes the exe to start the loading and the verification,giving
this message when finished:
''Written file Verified OK!''.
Now you can turn Hummy off,using STANDBY button on the box,
to save key-bin correctly.
-
-
modest supermod
definitive tps how to
hi all,
as found by Marco a guide to loading the tps.hdf
-
-
modest supermod
firmware update issue, and solution
as posted by ZAD,
firmware update issue
hi guys its banging head off the wall time for me!!!
i was given a 5400 with some issues mainly psu.
i have repaired this part and discovered the 5400 has no firmware on it as im getting the error code that corresponds to it so........
i have tried to upload new firmware however i have been getting the a-ut error code (firmware tx rx problem) so i have dropped the connection speed right down to the slowest possible and it starts off uploading the software but then crashes out!
any suggestions guys?
i have changed the crystal next to the com port and also went over the joints to check for drys but still the problem persists..
please help my head is going to go through the wall soon lol
solution,
ok problem solved and what a bi*ch!!!
the surface mount rs232 controller had went down
this was on a oak 2 board
the part was as follows
ic u340
part number adm239mjr
if anyone else ever has this issue and your ok working with surface mount components you may have to go down this road, however afer all the 5400's i have repaired this is the first time i have came across this issue so it may be an idea to elimated all other possible causes before going down the route i had to.
well anyways all sorted now if voith or any other mod wants to add this perticular issue to the stickies help section and the component in question!
-
-
modest supermod
guide to editing the pcm file
hi all,
to start with, mr dudes excellent guide to edit your pcm file in word form converted by a member whose name escapes me thanks m8
regards
voith
-
-
modest supermod
showtime key input
hi all,
as posted by marco how/where to input keys for showtime
go in the ram editor press blue on remote
go to the provider 1 before orf
leave the provider 000000
then enter daily keys on lines
showtime
lines 06 & 16 key 00
lines 07 & 17 key 01
art
lines 08 & 18 key 00
lines 09 & 19 key 01
-
-
modest supermod
loading order
hi all,
if you have any doubts about the order of loading, try this
patch
using hdfsmart and making sure all the modules are ticked on the left, or use hu15
pcm
if needed but always try without, when you load a full patch, the new pcm gets loaded as well.
channel settings
using hnfsmart or humbox
change caid to card+emu
change stb time to gmt +2 for tps
bin
using dsr9500 9.6
when you load the bin, do a verify as this will tell you if the bin has gone in
if this fails (and you will know in a couple of secs) and you have skipped the channel settings, then reload your channel settings as this cleans the bin out and allows you to load fresh
watch telly
hope this helps
voith
Last edited by voith driver; 16-08-2007 at 10:51 PM.
-
-
modest supermod
how to edit using hnfsmart
hi all,
this is written to move channels from one file to another using HNFSMART using the latest pet123 files, but the principle is the same for others.
to get 45E channels
first open file modified pet123+h to h mounts190707.hnf in hnfsmart
then open file toh_45east-43west-Humax-30-21.hnf in another hnfsmart
line up both and reduce them to a manageable size to work on screen
then go to provider in both editors and highlight 45E
one will have dummy channel in the other will have more channels using the one with the channels and making sure you are still highlighting the correct sat, go to
edit
select
all
it will all go blue then back to
edit
copy
then cross over to the other editor, making sure that one is also highlighting the correct sat, go
edit
paste (paste will only be available if you have correctly copied from the last)
now depending on how many channels you are moving i would give it some time just in case its not all transferred before you do anything else
when you are happy its finished moving then look at the bottom of the editor screen
you will see how many tv channels and how many radio channels you have, the aim is to reduce so that you have below 4000 in total, so its just a case of right click and delete if you are dumping 1 channel at a time, or its select all and right click and delete service, if you are doing it by provider
once you are happy save the file
i hope this helps
voith
-
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Bookmarks