MR to MM

[piratt]

Something fail to convert MR to MM with CAS-a, apparently forgetting something is not done, some can you tell me how it works?

[^^COMPASS^^]

How to get MM into MR ? and Get it back to MM again !

I'd like to provide the files and steps needed to convert your MM to MR or MR to MM

First , Converting MM to MR

You need Cas Interface 2 or 3

Open Cas Interface Studio :

1- Click on Matrix Reloaded
2- Insert your CAM (the Cas should reconize it) , then press Erase All
3- After Erasing the flash , Click Open File , Select MR1.XXX File.
4- Press Write
5- After writing the MR file , Write "Matrix.cas" in Xlinx.

That's all , Now you have your MM in MR

Converting MR to MM:

You need Cas Interface 2 or 3

Open Cas Interface Studio :

1- Click on Magic Module
2- Insert your CAM (the Cas should reconize it) , then press Erase All
3- After Erasing the flash , Click Open File , Select Dreamload.bin file , this file is important to get your cam in loader status , you will find many files , just take the file that fits your cam flash for example (Toshiba) is the flash of your MM , so choose Dreamload_Toshiba.bin file , and others in the same way
4- Press Write ,
5- After writing the MR file , Click open again and wrtie MM bin file (Pentacrypt 111) for example , before doing this go to Advanced Option and get start address to 10000 , Now back to General , Write MM penta file , after writing it , go to Xlink and choose Magic.cas file , write it

Now your CAM is MM

[^^COMPASS^^]

found more detailed info here by Goran

https://www.satpimps.co.uk/showthread.php?t=56632

[piratt]

How to get MM into MR ? and Get it back to MM again !

I'd like to provide the files and steps needed to convert your MM to MR or MR to MM

First , Converting MM to MR

You need Cas Interface 2 or 3

Open Cas Interface Studio :

1- Click on Matrix Reloaded
2- Insert your CAM (the Cas should reconize it) , then press Erase All
3- After Erasing the flash , Click Open File , Select MR1.XXX File.
4- Press Write
5- After writing the MR file , Write "Matrix.cas" in Xlinx.

That's all , Now you have your MM in MR

Converting MR to MM:

You need Cas Interface 2 or 3

Open Cas Interface Studio :

1- Click on Magic Module
2- Insert your CAM (the Cas should reconize it) , then press Erase All
3- After Erasing the flash , Click Open File , Select Dreamload.bin file , this file is important to get your cam in loader status , you will find many files , just take the file that fits your cam flash for example (Toshiba) is the flash of your MM , so choose Dreamload_Toshiba.bin file , and others in the same way
4- Press Write ,
5- After writing the MR file , Click open again and wrtie MM bin file (Pentacrypt 111) for example , before doing this go to Advanced Option and get start address to 10000 , Now back to General , Write MM penta file , after writing it , go to Xlink and choose Magic.cas file , write it

Now your CAM is MM

As described but I do not receive

[piratt]

After erase ALL i load Dreamload bin file after than i wrtie MM bin file (Pentacrypt 111)with adres 10000 but not joy maybe Penta file is not correct...How large must Penta bin.file ?

[McDude]

After erase ALL i load Dreamload bin file after than i wrtie MM bin file (Pentacrypt 111)with adres 10000 but not joy maybe Penta file is not correct...How large must Penta bin.file ?

Don't know if you have solved your problem or not.....the penta file is approx 60kb and should be in mbf format for cas 2/3