Enigma 2 by The_ripper - TEST -

Some feedback after trying 1.0.28 on premium:

Mediaplayer:
.srt subtitles works, but tags like italian isnt supported, so the tags are displayed like text. (..but I think this happens on DM800 as well.)
It would have been nice to have this fixed, either by supporting them or just make the tags get ignored so they doesnt show.

On DM800 the settings done in the system/AV-settings for 4:3 and 16:19 will also apply for the mediaplayer. It doesnt seem to do that on the Azbox.

Audio seems to get out of sync after a while.
No sound at all on mp4 h264 files. One of these had two audio tracks listed, trying to change to the other track does make the kog wheels go again until reboot.
Also I found that on these files .srt files are not selectable. Even if they have the same filename as the mp4 file, there are no subtitles listet.

Tuner:
Working with diseq 1/8 switch. All LNBs scanned without problems.
But to save work, I used DreamboxEdit4 to copy channel lists and favourites from my DM800 setup.
All seem to work, but I had some problems with some channels that cause the box to stop when I try to change channel. (kog wheels spins forever, so I reboot)
It seemed to be most often on some HD channels that had two identical entries in the channel list. I did delete it from the favourite list and found the working one in the channellist, and re-added it to the favourites. That seem to work, but after next reboot it was the same problem again. Solution was to find the SID for the working channel, then use DreamboxEdit to delete the other entries that was causing trouble.
But still there are occasional "kog wheel spin forever" when zapping.
Also have the sound problem like everyone else.

General:
Sometimes after a reboot the HDMI output isnt activated, only scart is usable.

Also I notice that in many places in the menues, the word Dreambox is still used. Are there plans to replace that before first non-alpha release with eg Azbox-E2 or something?

Streaming from webinterface doesnt work

Quote:

---

Originally Posted by amyren

Some feedback after trying 1.0.28 on premium:

Mediaplayer:
.srt subtitles works, but tags like italian isnt supported, so the tags are displayed like text. (..but I think this happens on DM800 as well.)
It would have been nice to have this fixed, either by supporting them or just make the tags get ignored so they doesnt show.

On DM800 the settings done in the system/AV-settings for 4:3 and 16:19 will also apply for the mediaplayer. It doesnt seem to do that on the Azbox.

Audio seems to get out of sync after a while.
No sound at all on mp4 h264 files. One of these had two audio tracks listed, trying to change to the other track does make the kog wheels go again until reboot.
Also I found that on these files .srt files are not selectable. Even if they have the same filename as the mp4 file, there are no subtitles listet.

Tuner:
Working with diseq 1/8 switch. All LNBs scanned without problems.
But to save work, I used DreamboxEdit4 to copy channel lists and favourites from my DM800 setup.
All seem to work, but I had some problems with some channels that cause the box to stop when I try to change channel. (kog wheels spins forever, so I reboot)
It seemed to be most often on some HD channels that had two identical entries in the channel list. I did delete it from the favourite list and found the working one in the channellist, and re-added it to the favourites. That seem to work, but after next reboot it was the same problem again. Solution was to find the SID for the working channel, then use DreamboxEdit to delete the other entries that was causing trouble.
But still there are occasional "kog wheel spin forever" when zapping.
Also have the sound problem like everyone else.

General:
Sometimes after a reboot the HDMI output isnt activated, only scart is usable.

Also I notice that in many places in the menues, the word Dreambox is still used. Are there plans to replace that before first non-alpha release with eg Azbox-E2 or something?

Streaming from webinterface doesnt work

---

mp4 h264 --> this is aac audio?. cause new release will fix this.

Fixed m2ts h264 playback. Other format VC1 is not yet supported.

Quote:

---

Originally Posted by MoGaZz

Have you managed to get some samples? Let me know if you haven't. I can arrange some mkvs with h24, xvid and mpeg2 for you.

---

Please provide me with the samples

My experiance with .28:
- Works also from HDD - seems a bit slower than from DOM.
- Monoblock is working with Hotbird and Astra
- Sound is mostly bad if it works. But most channel do not give any sound.
I'm using only HDMI for Sound

dmesg shows

DVB: audio0 play command sended to the audio decoder
dvb_ca_ioctl: Error - invalid ioctl 80086f87
dvb_ca_ioctl: Error - invalid ioctl 80086f87
dvb_ca_ioctl: Error - invalid ioctl 80086f87
dvb_ca_ioctl: Error - invalid ioctl 80086f87
dvb_ca_ioctl: Error - invalid ioctl 80086f87
DVB: Error EMhwlibReceiveBuffer! RM_INSUFFICIENT_SIZE -> for PID 0012
out of order segment: rcv_next FEFB0C47 seq FEFB0C8E - FEFB0C96
out of order segment: rcv_next FEFB0C47 seq FEFB0C96 - FEFB0D31
out of order segment: rcv_next FEFB0C47 seq FEFB0D31 - FEFB0DDC
ofo requeuing : rcv_next FEFB0C8E seq FEFB0C8E - FEFB0C96
ofo requeuing : rcv_next FEFB0C96 seq FEFB0C96 - FEFB0D31
ofo requeuing : rcv_next FEFB0D31 seq FEFB0D31 - FEFB0DDC
out of order segment: rcv_next FEFB0F22 seq FEFB0FBD - FEFB0FC5
out of order segment: rcv_next FEFB0F22 seq FEFB1060 - FEFB11A6
ofo requeuing : rcv_next FEFB0FBD seq FEFB0FBD - FEFB0FC5
ofo requeuing : rcv_next FEFB1060 seq FEFB1060 - FEFB11A6

This is with broken sound if I change to another I get

vb_ca_ioctl: Error - invalid ioctl 80086f87
dvb_ca_ioctl: Error - invalid ioctl 80086f87
dvb_ca_ioctl: Error - invalid ioctl 80086f87
dvb_ca_ioctl: Error - invalid ioctl 80086f87
dvb_ca_ioctl: Error - invalid ioctl 80086f87
DVB: Stop STC!
DVB: video0 stop command sended to the video decoder
dvb_video_release
DVB: audio0 stop command sended to the audio decoder
DVB: audio0 play command sended to the audio decoder
DVB: video0 Open the pools
DVB: video0 dmapool id = 2
DVB: video0 count : 1, timeout = 10000
DVB: audio0 Open the pools
DVB: audio0 dmapool id = 3
DVB: audio0 Channel Status from SPDIF: 0x1900 0x0004
DVB: audio0 count : 1, timeout = 10000
DVB: video0 play command sended to the video decoder
DVB: audio0 play command sended to the audio decoder
dvb_ca_ioctl: Error - invalid ioctl 80086f87
dvb_ca_ioctl: Error - invalid ioctl 80086f87
dvb_ca_ioctl: Error - invalid ioctl 80086f87
dvb_ca_ioctl: Error - invalid ioctl 80086f87
dvb_ca_ioctl: Error - invalid ioctl 80086f87
DVB: Error EMhwlibReceiveBuffer! RM_INSUFFICIENT_SIZE -> for PID 02CD

and no sound.

- Webgui works OK

But really good work in this short time!

The_Ripper already knows about sound, this is not a bug/error, he simple didn't code a part that is needed. A timer.

SATTOMY regarding some .srt don't show up in AUX and movies start losing sound and going slow motion after a couple of minutes, do u have any idea why?
Thank you.

zfeet
Junior Member Join Date: Apr 2010
Posts: 26
Thanks: 19
Thanked 18 Times in 7 Posts

Quote:
Originally Posted by mounirmoune12
My azbox don all the steps but my problem is azup error

(file not foond unable to complete rquest). i tried all fw, unstall and install azup and used tow usb stick one formated fat 32 and one ntcs , windows vesta and xp.
nothing work and i dont know what to do .3 days no tv so far

pls help



I had the same issue when Azup was installed in the default location in Program Files. Copy AZUp.exe from "C:\Program Files\telesat\AZUp" to a different location and run as Administrator.



I don that too but no think. thanks for replay

ols help

Quote:

---

Originally Posted by sattommy

mp4 h264 --> this is aac audio?. cause new release will fix this.

Fixed m2ts h264 playback. Other format VC1 is not yet supported.

---

Sorry, I dont know if its aac audio or not. I will be away from home now for three weeks now, so I will test new releases when I'm back.

Also, I must correct myself about my statement about that the audio gets out of sync.
It is synced as long as I dont touch anything and just let the video play. But if I do anything, like try to pause and resume or try to skip back or forward with the number buttons, the audio will get out of sync.

three weeks? :P
in three weeks i can't imagina how much progress will be done :P

Quote:

---

Originally Posted by sattommy

Please provide me with the samples

---

You can download the video samples from here:

http://www.4shared.com/file/YWGR3FW3/samples.html

I mixed aac, mp3 and ac3 (direct copy) streams into 3 files (h264, xvid and mpeg2). Two of them have bitmap subtitles. I can add srt subtitles later if you want me to.

The clips have only 20 seconds, let me know if you need more than that.

The files were created with handbrake 094. Mpeg2 file was muxed with mkvmerge. The files were tested with vlc and are ok.

I have a problem when I try to go back to fw 1.0.27. Azup stop in 59 seconds with "patch.cramfs Created."
If I try to return official firmware 0.9.50 , Azup stop in 1 minute and 5 seconds with the same message: patch.cramfs Created
If I restart Azbox, fw 1.0.28 work ok but too many locks.
I format the flash drive (2GB) in fat32 ==> no solution
I remove and install again Azup ==> no solution
When you close the error window tells me that enigma2 has been installed correctly, but is false ... nothing is installed. Also, try to install official firmware 0.950 to return to 1.0.27 not try install enigma2.
Any solution?
Sorry for my english.

Quote:

---

Originally Posted by MoGaZz

You can download the video samples from here:

http://www.4shared.com/file/YWGR3FW3/samples.html

I mixed aac, mp3 and ac3 (direct copy) streams into 3 files (h264, xvid and mpeg2). Two of them have bitmap subtitles. I can add srt subtitles later if you want me to.

The clips have only 20 seconds, let me know if you need more than that.

The files were created with handbrake 094. Mpeg2 file was muxed with mkvmerge. The files were tested with vlc and are ok.

---

Thnx,

I will have a look.

@hmfls

I dont know hy some dont show up. Please send me one of the srt files which do not show. For subtitles we use the same as dreambox, no additions made there yet.

When video stops he seems to error on the demuxer.

Quote:

---

Originally Posted by amyren

Sorry, I dont know if its aac audio or not. I will be away from home now for three weeks now, so I will test new releases when I'm back.

Also, I must correct myself about my statement about that the audio gets out of sync.
It is synced as long as I dont touch anything and just let the video play. But if I do anything, like try to pause and resume or try to skip back or forward with the number buttons, the audio will get out of sync.

---

I think this has something to do with. I will focus on this a little later.

After doing some tests with IPkg browser packs etc.

After boot I get now "Webinterface couldn't listen on 127.0.0.1:80"
The network services are not activated.
I have to activate them with remote control via menu and the all is ok.

SO where is that damm settings file where the network setting is hidden.

Here is my feedback about Enigma 2.

First I had some problems with the installation. I found that I could not use the wireless connection. I plugged inn the wire, and I installed the firmware without problems using AZUp.
When I should update to the latest version, I did not get the IP address in the display, but then the issue was that I had the external USB hard drive connected to the rear, and the USB in the front. I disconnected it, and I updated without problems.

The hard drive is a external Western Digital 1Tb, and it works.

I have 8 lnb`s, and I can confirm that this works :-)

I see that it does not support playback of recordings that I have (TS-Files), but it plays many other formats. This will probably be improved.

I miss being able to use the buttons on the remote control as usual, but this is just a habbit.

The biggest lack for me is support for DVB-T, but this will probably work in the future.


Great work guys :cup-006:

@sattommy

Maybe this has something to do with encoding...utf-8, etc.

Quote:

---

Originally Posted by leif666

Here is my feedback about Enigma 2.

First I had some problems with the installation. I found that I could not use the wireless connection. I plugged inn the wire, and I installed the firmware without problems using AZUp.
When I should update to the latest version, I did not get the IP address in the display, but then the issue was that I had the external USB hard drive connected to the rear, and the USB in the front. I disconnected it, and I updated without problems.

The hard drive is a external Western Digital 1Tb, and it works.

I have 8 lnb`s, and I can confirm that this works :-)

I see that it does not support playback of recordings that I have (TS-Files), but it plays many other formats. This will probably be improved.

I miss being able to use the buttons on the remote control as usual, but this is just a habbit.

The biggest lack for me is support for DVB-T, but this will probably work in the future.


Great work guys :cup-006:

---

please upload sample

Please guys, a tutorial to dual boot needed. Boot enigma from usb1 and original from dom, so we can test this alpha and beta stage.

Pleeeeseeee

Here is a sample off a recording that workes on my other azbox, but not on the Enigma 2 box.
I use VLC to watch it on the computer.

cheers :cool:

Quote:

---

Originally Posted by moicas3004

Please guys, a tutorial to dual boot needed. Boot enigma from usb1 and original from dom, so we can test this alpha and beta stage.

Pleeeeseeee

---

i dont even know that was possible, that i really want, watch everything in E2 sleep in original xD

Quote:
Originally Posted by mounirmoune12
My azbox don all the steps but my problem is azup error

(file not foond unable to complete rquest). i tried all fw, unstall and install azup and used tow usb stick one formated fat 32 and one ntcs , windows vesta and xp.
nothing work and i dont know what to do .3 days no tv so far

pls help



I had the same issue when Azup was installed in the default location in Program Files. Copy AZUp.exe from "C:\Program Files\telesat\AZUp" to a different location and run as Administrator.



I don that too but no think. thanks for replay

pls help

Quote:

---

Originally Posted by sattommy

Framedrops on this 700mb avi you mean? I have watched some mkv series and it worked very well.

If i have time i will test some longer avis etc.....

Dont expect perfect playback right away please ;-)

@zfeet

i think there is a css library as well, but first menus.

@cirio

You can add lines to mount in a startup script. Just mount it to /media/hdd And hdd will show in mediaplayer

---

ok here is the .srt that doesn't even show up in AUX menu
it has the same name as .avi etc.

To be clear in what happens to me:

I press ok to play a 700mb movie (.avi XVID) in mediaplayer
with .srt with same name.
After i press ok to play movie, movie starts and i press AUX to select .srt, after i select .srt , subtitles only appear like 1 minute later (correctly, but they take 1 mnt or so to show) and after 2..3 minutes of movie playing correctly and with subtitles showing up, movie goes slow motion and audio disappears and subtitles stop to show up too, and this goes on.

If u need faster tests of anything u code i can test new files, i'm free all day and night (i work at home). And i use all kinds of media.
thank you

Enigma 2 v1.0.29
Devices suitable for flashing : Elite and Premium

What is new :

- MyTube plugin (YouTube)

- Multimedia fix for various formats by sattomy

Download:

Enigma v1.0.29

ATTENTION: Use AzUP v1.1 for Flashing this version of Enigma 2 into Your devices !!!

YouTube videos playing too fast (sound at normal speed)

EDIT: OK, _some_ videos playing too fast :)

@kasukabe,

always with the same video, or it's a random issue?

if possible, put links for these videos for more testings

@1.0.29

- mp4 h264 aac sound is ok now
- m2ts playable now but mts(the same as m2ts format) is still not in the list. I've to rename to m2ts to play my clip(fix it, please)
- Mytube work great. Watching HD clip without any problem.

Thanks......

Quote:

---

Originally Posted by hfmls

ok here is the .srt that doesn't even show up in AUX menu
it has the same name as .avi etc.

To be clear in what happens to me:

I press ok to play a 700mb movie (.avi XVID) in mediaplayer
with .srt with same name.
After i press ok to play movie, movie starts and i press AUX to select .srt, after i select .srt , subtitles only appear like 1 minute later (correctly, but they take 1 mnt or so to show) and after 2..3 minutes of movie playing correctly and with subtitles showing up, movie goes slow motion and audio disappears and subtitles stop to show up too, and this goes on.

If u need faster tests of anything u code i can test new files, i'm free all day and night (i work at home). And i use all kinds of media.
thank you

---

In the background mediaplayer detects them, but i think he has a problem parsing them. Please if you have time compare working and non-working srt files to find characteristics why they might not play.

Already did that, this 2 files i send here.
Alice in wonderland doesn't even show up when i press AUX.
Other file i send is x.srt, appears in AUX list and it shows when i press OK.
But it only shows after a few seconds or so, is it possible to put subtitles ON by default?

here are the files that show up and work, and don't show.

edit: i think i know what is the problem!!
Alice in Wonderland.srt was Encoded in ANSI and x.srt (the ones that show up and work) is in UTF-8.

I'm gonna Encode it in UTF-8 and see if they show up :)


edit2: YES THE PROBLEM WAS ANSI, NOW IN UTF-8 WORKS :) just use notepad and save it as UTF-8 instead of ANSI.

I found another problem/bug, everytime i press exit in remote to leave movie ( there is no stop button) no (before didn't happen) instead of leaving movie, it goes forever showing cogs sniping and stays there forever, i have to reboot manually box. Any idea why? Or should we start to map keymap? :)
It's getting pretty good.

Quote:

---

Originally Posted by hfmls

Already did that, this 2 files i send here.
Alice in wonderland doesn't even show up when i press AUX.
Other file i send is x.srt, appears in AUX list and it shows when i press OK.
But it only shows after a few seconds or so, is it possible to put subtitles ON by default?

here are the files that show up and work, and don't show.

edit: i think i know what is the problem!!
Alice in Wonderland.srt was Encoded in ANSI and x.srt (the ones that show up and work) is in UTF-8.

I'm gonna Encode it in UTF-8 and see if they show up :)


edit2: YES THE PROBLEM WAS ANSI, NOW IN UTF-8 WORKS :) just use notepad and save it as UTF-8 instead of ANSI.

I found another problem/bug, everytime i press exit in remote to leave movie ( there is no stop button) no (before didn't happen) instead of leaving movie, it goes forever showing cogs sniping and stays there forever, i have to reboot manually box. Any idea why? Or should we start to map keymap? :)
It's getting pretty good.

---

The cogs showing is a known bug. I will have to fix this otgether with the driver. Will be done later.

So for everybody: save your srt files to UTF-8, this is a limiation of the parser.

cool, thank you very much :)
by the way, i don't have a clue how to map keymap, could u give an example? i don't mind to spend a few hours doing it manually and share with you guys.
i want to map keys in mediaplayer stop, pause and play and others of course.
mytube i noticed is already mapped :P

Quote:

---

Originally Posted by hfmls

cool, thank you very much :)
by the way, i don't have a clue how to map keymap, could u give an example? i don't mind to spend a few hours doing it manually and share with you guys.
i want to map keys in mediaplayer stop, pause and play and others of course.
mytube i noticed is already mapped :P

---

check pm

I would like to participate in the testing phases of enigma2 project

...but

i cannot do that, since there is no capability YET, to:

-boot enigma from USB (leave original crap untouched)
-run enigma from HDD when there is DVB-T tuner connected (it is reported that dvb-t tuner must be disconnected).

if i am missing sthg please reply.

thanks again for your efort doing our azbox a better stb.

Quote:

---

Originally Posted by nstergi

I would like to participate in the testing phases of enigma2 project

...but

i cannot do that, since there is no capability YET, to:

-boot enigma from USB (leave original crap untouched)
-run enigma from HDD when there is DVB-T tuner connected (it is reported that dvb-t tuner must be disconnected).

if i am missing sthg please reply.

thanks again for your efort doing our azbox a better stb.

---

@ALL

Just posted a howto for usb booting in a new topic

Is the sound problem fixed?

Quote:

---

Originally Posted by frantisheq

youtube has greater priority than internal card reader. oh well. still waiting

---

Different people with different skills working on different parts. Please if you have energy to post stuff like this, use this energy to code driver yourself

Quote:

---

Originally Posted by frantisheq

relax. i'm just using azbox to watch sat. TV not youtube, mkv, photos, etc. have pc for that. not sure writing 12 words will fix the reader.

---

People like you don't deserve anything...
Don't talk like you are paying these guys....
With that attitude, if I was the ripper I would never fix the reader...
As......

****Center also works very well....

I have the premium model with wifi and dvbt. Both are still functioning?

Quote:

---

Originally Posted by MickeySa

****Center also works very well....

---

is there any plugin with all sites?
like you**** ****hub ****tube xvideos etc?

Just for STUDY porpuses!:woohoo-022::woohoo-022::woohoo-022:

Quote:

---

Originally Posted by frantisheq

jesus christ people get a prosac or something. live maybe

---

Another guy saying just s*** around here... I swear, I cant understand why you come here just to say those things...!

Quote:

---

Originally Posted by AAOM

I have a problem when I try to go back to fw 1.0.27. Azup stop in 59 seconds with "patch.cramfs Created."
If I try to return official firmware 0.9.50 , Azup stop in 1 minute and 5 seconds with the same message: patch.cramfs Created
If I restart Azbox, fw 1.0.28 work ok but too many locks.
I format the flash drive (2GB) in fat32 ==> no solution
I remove and install again Azup ==> no solution
When you close the error window tells me that enigma2 has been installed correctly, but is false ... nothing is installed. Also, try to install official firmware 0.950 to return to 1.0.27 not try install enigma2.
Any solution?
Sorry for my english.

---

Complete format USB drive and i install 1.0.29 ==> all ok.