but that would delete all the channels
Printable View
but that would delete all the channels
set for usals,scan hotbird and save,open set editor and download box,save to desktop,look on desktop for new channel list and upload to receiver,check and change usals cause they may be different to yours,talk to you later to day if that is okay
where do you live roughly.
done
you say done what does that mean m8.
When you change to usals it deletes the chanels. I 've started to reload the settings after chaging to usals. we'll see what happens after this. If I keep getting this I'll contact Humax for asistance
All I did was change to my usals and scan that is all you should have to do,
Sorry I think I miss read you. I'e already started to load the setting again after changing to usals. If that does not work than I may have to do thi manually if I an. I miss my satelite.
set your receiver to correct usals then do channel search of hotbird,and save.
I'm too far between the satellite signal/TV and the PC. One up stairs and the main T is down stairs.
This is why i'm making mistakes. I'll do a search on hotbird now and save
Maud Thanks for now I'll speak to you tomorrow. I working tomorrow morning. I'll follow your last instruction tomorrow and see what happens. I thnk my satelite is refusing the settings.
I have some cat5 cable made off to 9 pin D sockets and plugs etc running 10 metres to my computer to enable communication to my box this I have found okay,you must be able to talk to your box whilst it is connected to antenna and tv.
i'm not at home at present but I've done what you said yesterday by changing it the Usals and searching on Hotbird. When I try to search for another sat it says it will delete whats on the receiver.
I've spoken to Humax today with regards to the receiver. I hope to get an answer soon.
My problems is still not yet solved as I can't see the new channels once uploaded to the reciever.
Hi Pajao,
Is it possible that you set it up as fixed antenna/dish?
That might explain why it says it is going to delete everything when you try to look for another sat.
HDCI Manual:
2. Motor Antenna
When using a motor antenna, set the antenna to Motor before performing channel search...
tinto de verano
That could explain things. Pajao, Antenna Config will show the Diseqc version (1.0 or 1.2) in your downloaded channel list in Formula.
Thanks mate. Im back on Shall I remove the fomula and reinstall a new formula file to upload the new settings?
Hi Pajao,
If the program you have in your PC is formulaforhd_eu1.01, and you are in Europe, it should be OK. I do not think you need to remove and reinstall.
Now assuming that is the program you have, that you have SatPual's latest list...
Make sure you have configured properly your HDCI2000.
As already expleained, complete the setup.
Make sure you set it up for Motor Antenna (see my previous post, yesterday, 11:23 PM).
Load up Satpauls channel list in Formula (do not add remove any channels, not even radio, just in case).
You could change the USALS info, if you know your location, or change it to Diswq (maybe safer).
If you change anything, save the file with a different name so that you always have SatPaul's original file as you downloaded it from here.
Download the Channel list from Formula/PC to your HDCI2000.
Bear in mind it takes a while, and it does 2 or 3 passses, I seem to remember, so wait till you are completely sure the list has been transferred to the HDCI20000.
Good luck.
I'll check later to see how you are doing.
tinto de verano
I've removed and install the formula loader, followed your instructions but still no channel list on the receiver. I think there's a problem with the receiver receiving new settings from the loader. Ill complain to Humax to see what they can do. Thanks for your help on this.
Hi Pajao,
Sorry to hear you have not succeeded.
Good luck with Humax.
tinto de verano
Are you turning the receiver off at the back and on again,does your computer show it is connected and downloading,
Yes,
But when it end there are no channels. I think there is problems with my Box not receiving the settings & updating the box. I had no problems wirth the Firmware though using the loader from Humax.