Blagi have you tried this how says Bundersuk and ManikM?
Has anyone tried it so.
Thank you.
Printable View
Blagi have you tried this how says Bundersuk and ManikM?
Has anyone tried it so.
Thank you.
No, I haven't. Thankfully, there was no need to...
Thanks a lot for that advice. Worked for me too that way. RegardsQuote:
Originally Posted by bundersuk
i am trying to recover an azbox premium stuck on bootup but when click open on putty and switch on azbox i get this message from putty:
yxosPc0 serial#e153f9baec7f4e68ad9aefa392 582dce subid 0xc4
xenv cs2 ok
Power supply: FAIL
any help will be very appreciable
the guide is amazing, cant beleive how helpful it is! brought a dead az back to life !
never trying that AZTRINO nonsense again.
My Az Box was stuck on wizard zamba and not booting up.Found official firmware on a italian az box forum .File was in rapidshare.Downloaded it and booted up usb stick.Had option to format which I did first.I then put usb stick back in and used update option.Az box then updated and started working normally.
If you dont format nothing happens.Use at own risk.
Hi Muja,
I get the exact same error in Putty as you. Have been trying to recover my Azbox. I have followed the full instructions, however that is the result I get. I have tried 3 times now and get the same result each time. Any suggestion? We're you able to resolve this issue? Any help would be appreciated
Processing xrpc_xload_yamon_ES4_prod.bin (start: 0x8c040090, size: 0x0002fe84)
Checking zboot file signature .. Not found.
Trying xrpc_xload format .. OK
Checking zboot file signature at 0x13000000 .. OK
Decompressing to 0x91200000 .. OK (453328/0x6ead0).
Load time total 173/255 msec.
Execute final at 0x91200000 ..
********************************* *
* YAMON ROM Monitor
* Revision 02.06-SIGMADESIGNS-01-2.8.0.1
********************************* *
Memory: code: 0x11000000-0x11040000, 0x11200000-0x11204000
reserved data: 0x11240000-0x12440000, PCI memory: 0x12440000-0x12840000
Environment variable 'start' exists. After 1 seconds
it will be interpreted as a YAMON command and executed.
Press Ctrl-C (or do BREAK) to bypass this.
xrpc failed (9)--- if a xtask is using a cipher or if you reboot
--- xrpc will fail with RM_BUSY
Checking zboot signature.. it's not zboot file.
Error : Internal, code = ffffffff
thanks
niall
it does say in the guide, that if you get anything other than a certain error\code, then the process is no good, and its bricked.
i was getting the ffffffff error with windows 7, i kept trying and by chance it worked all of a sudden, don`t know whether it was a windows 7 problem or not, do you use windows 7?, and make sure all firewalls are off.
the yamon in the flash mem is damaged which means you cannot use any of the files to repair it if tou are a electronic wizard then ok you need to jtag the chip if not it looks like you need to send the box back to where you bought it from first you must go to this site and make out a work ticket they are very helpfull
http://www.azbox.com
xosPe0 serial#820febe7f9abab9f5e08fd3d33 fd0e73 subid 0x50
xenv cs2 failed
xenv cs3 failedĄřpower supply: ok
dram0 ok (9)
zboot (1) failed
Is there any news?
Please help.
I have the same issue is there an alternative other than the jtag solder or
Returning to opensat .
Thanks
Hi,
For people that follow this recovery procedure, the provided kernel is an old one.
Since they change the boot parameter in Yamon when you are in Yamon, you need to type this command to restore "old kernel" boot parameter otherwhise your Azbox will not boot the old kernel.
Remark: to boot kernel 3.4.4 and 3.5.5 the value is:Code:setxenv y.start "xrpc 0xac080090; load zbf 0xb3000000; go"
Hope this help,Code:setxenv y.start "dump romfs 0xac080000;load zbf 0xac080090; go"
Pr2
P.S.: May I suggest to moderator to include this in the first post.
twice now this guide has saved my azbox! top guide, a little confusing at times, but not that hard
are there any tutorials/video clips out there on jtag-ing the chip - i found one on youtube in relation to the dm box - but cant find any for the azbox - thanksQuote:
Originally Posted by majz
Please try again with another cable or adapter, if it is possible with Nokia cable, since you have zboot OK. "Checking zboot file signature at 0x13000000 .. OK " Could be conexion problem.Quote:
Originally Posted by boc555
If not you can follow the spanish instruccion of this tutorial.: http://openspa.info/threads/tutorial...ia-jtag.12602/
You could read the solution here :Quote:
Originally Posted by boc555
https://www.satpimps.co.uk/showthrea...d-not-beat-me-!!!!!!!
This is what I get:
þxosPe0 serial#94fa0efeecaed757143d3c8d1d 0e876b subid 0x50
xenv cs2 failed
xenv cs3 failed¡ÃxosPe0 serial#94fa0efeecaed757143d3c8d1d 0e876b subid 0x50
xenv cs2 failed
xenv cs3 failed¡ÃxosPe0 serial#94fa0efeecaed757143d3c8d1d 0e876b subid 0x50
xenv cs2 failed
xenv cs3 failed¡Ãpower supply: failed
dram0 ok (8)
zboot (1) failed
arthurbf, you have to use JTAG.
Hi, can someone help me on this?
I have a AZbox premium HD that is stuck in booting. I've connected a serial to the Yamon interface and used 115200 bits/sek but the outcome from Putty is not readable (see image)
Attachment 55937
I've also tried all the other bits/sec setting but none is readable. Anyone familiar with this?
Try to change RX and TX