Enigma 2 by The_ripper - TEST -

Printable View

Show 40 post(s) from this thread on one page

21-09-2010, 11:02 PM
far451

AZUp setup.exe installation on Ubuntu

For all those Ubuntu 10.04 users out there, when installing 'AZUp setup.exe' using wine, you may see the error messages...

X Error of failed request: XF86VidModeExtensionDisabled
Major opcode of failed request: 129 (XFree86-VidModeExtension)
Minor opcode of failed request: 6 (XF86VidModeGetAllModeLines)
Serial number of failed request: 85
Current serial number in output stream: 85

To get around this, append the following to user.reg

cat ****"$HOME/.wine/user.reg" <<EOF

[Software\\\\Wine\\\\X11 Driver] 1280580367
"U***VidMode"="N"
EOF

Then use

wine regedit

and make sure

HKEY_CURRENT_USER\Software\Wine\X 11 Driver\U***VidMode = "N"

I have tried

wine AZUp.exe

to verify the window loads, but have NOT tried using it for recovery.

Many thanks to THE_RIPPER et al
21-09-2010, 11:33 PM
MickeySa

For all members which own, AzBox HD Premium+ here is tutorial how to make E2 test running on their STB.

So, use standard procedure, to load E2 in Premium+, same as Elite/Premium.

Now, reboot Yout STB with usb memory stick in it with patch.bin file on it, just to enter in RECOVERY MODE, to obtain IP Address of Your receiver.

When You noted IP address of AzBox HD Premium+ ( which You can also do by accessing Router of Your LAN ), remove USB Memory stick, and turn off and turn on AzBox HD Receiver, by the power switch on the back side.

When You got on VFD 100, Your box is up and running.

Use FTP to connect on IP address which You already noted, and go in /etc/init.d .

There, You will find file named as bootup.

Download and Edit it.

Inside of it You will find two lines :

# Elite and Premium
insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f PAL_BG -digital -f HDMI_720p50 -hdmi_chip SiI9030 0 14 15 100 0"
# Premium+
#insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f PAL_BG -digital -f HDMI_720p50 -hdmi_chip SiI9134 0 14 15 100 0"

Comment insmode line below # Elite/Premium with character #.

Uncomment insmod line below #Premium+ , save file and overwrite existing file on STB.

Now, switch off and switch on Your Premium+, and You should have GUI and everything on Your Premium+ .

The problem is just as Elite/Premium are using Sil9030 HDMI Chip, and Premium is using Sil9134 . So it is same procedure to get it working on AzBox Ultra HD.
22-09-2010, 03:14 AM
digitaly

Hi! thank you for your work I would like to say
But I followed the readme text and used a fat 32 64 mb usb flashdrive (could it be that I have left a ch and a cam back up into it?),

I also ended up with "geko :P"
on my router (wrt600n DD-WRT) it's still showing my static IP for the box "192.168.3.129"
if I try to ping that IP I get "request timed out"
I restarted my pc and nothing.
Any advice?
22-09-2010, 07:41 AM
satdish101

Thank you for the assistance. For those of us in North America using NTSC, would the correct modification to the display line be,

# Premium+
insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f NTSC_M -digital -f HDMI_720p60 -hdmi_chip SiI9134 0 14 15 100 0"

If at all possible, please consider one ver of E2 for AZbox HD models (Elite, Premium, Ultra, Premium+) :respect-040:

Quote:

Originally Posted by MickeySa

For all members which own, AzBox HD Premium+ here is tutorial how to make E2 test running on their STB.

So, use standard procedure, to load E2 in Premium+, same as Elite/Premium.

Now, reboot Yout STB with usb memory stick in it with patch.bin file on it, just to enter in RECOVERY MODE, to obtain IP Address of Your receiver.

When You noted IP address of AzBox HD Premium+ ( which You can also do by accessing Router of Your LAN ), remove USB Memory stick, and turn off and turn on AzBox HD Receiver, by the power switch on the back side.

When You got on VFD 100, Your box is up and running.

Use FTP to connect on IP address which You already noted, and go in /etc/init.d .

There, You will find file named as bootup.

Download and Edit it.

Inside of it You will find two lines :

# Elite and Premium
insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f PAL_BG -digital -f HDMI_720p50 -hdmi_chip SiI9030 0 14 15 100 0"
# Premium+
#insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f PAL_BG -digital -f HDMI_720p50 -hdmi_chip SiI9134 0 14 15 100 0"

Comment insmode line below # Elite/Premium with character #.

Uncomment insmod line below #Premium+ , save file and overwrite existing file on STB.

Now, switch off and switch on Your Premium+, and You should have GUI and everything on Your Premium+ .

The problem is just as Elite/Premium are using Sil9030 HDMI Chip, and Premium is using Sil9134 . So it is same procedure to get it working on AzBox Ultra HD.
22-09-2010, 07:55 AM
pe.tardo

Quote:

Originally Posted by far451

For all those Ubuntu 10.04 users out there, when installing 'AZUp setup.exe' using wine, you may see the error messages...
...

To get around this, append the following to user.reg

cat ****"$HOME/.wine/user.reg" <<EOF

...

What means **** ?
Thx.

(Thx to The_Ripper & Team too, for their hard work)
22-09-2010, 08:25 AM
satdish101

MickeySa,
By making the change to the bootup file as you suggested (including commenting and uncommenting) using:

insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f NTSC_M -digital -f HDMI_720p60 -hdmi_chip SiI9134 0 14 15 100 0"

I am able now to get my HDMI (NTSC) to display however I do not get past the occasional spinning gears :(

If my syntax is wrong for an NTSC HDMI display please advise. If my video is properly configured, it appears that E2 is not loading?

Thank you :respect-061:
22-09-2010, 08:37 AM
Carp95

Quote:

Originally Posted by MickeySa

For all members which own, AzBox HD Premium+ here is tutorial how to make E2 test running on their STB.

So, use standard procedure, to load E2 in Premium+, same as Elite/Premium.

Now, reboot Yout STB with usb memory stick in it with patch.bin file on it, just to enter in RECOVERY MODE, to obtain IP Address of Your receiver.

When You noted IP address of AzBox HD Premium+ ( which You can also do by accessing Router of Your LAN ), remove USB Memory stick, and turn off and turn on AzBox HD Receiver, by the power switch on the back side.

When You got on VFD 100, Your box is up and running.

Use FTP to connect on IP address which You already noted, and go in /etc/init.d .

There, You will find file named as bootup.

Download and Edit it.

Inside of it You will find two lines :

# Elite and Premium
insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f PAL_BG -digital -f HDMI_720p50 -hdmi_chip SiI9030 0 14 15 100 0"
# Premium+
#insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f PAL_BG -digital -f HDMI_720p50 -hdmi_chip SiI9134 0 14 15 100 0"

Comment insmode line below # Elite/Premium with character #.

Uncomment insmod line below #Premium+ , save file and overwrite existing file on STB.

Now, switch off and switch on Your Premium+, and You should have GUI and everything on Your Premium+ .

The problem is just as Elite/Premium are using Sil9030 HDMI Chip, and Premium is using Sil9134 . So it is same procedure to get it working on AzBox Ultra HD.

Hmm having problem with this one.
Installed like Elite/Premium
Got Ipadres

Waited till VFD gave 100
Changed bootup
Reboot

In VFD I got

- Usb check
- Resque mode
- Resque mode?

And then stays black nothing is happening?

Will try to go back to original

EDIT: No GO!! Resque mode appears but no network! no ipadress.
22-09-2010, 08:43 AM
xanadu

Quote:

Originally Posted by pe.tardo

What means **** ?
Thx.

(Thx to The_Ripper & Team too, for their hard work)

cat > >"$HOME/.wine/user.reg" <<EOF

Remove the spaces between > >

It's a standard command to change a registry value
22-09-2010, 09:11 AM
Carp95

Falls alarm reformated USB stick now it's in recover mode
22-09-2010, 09:11 AM
leerock

I ve tried ripper's updated ko and boot files and the boot time is a bit faster now!!!

1080p is not included in the av settings menu (obviously because it s not a part of e2)

I don't know if it will ever be added but I don t really care...
22-09-2010, 09:42 AM
VFL

Quote:

Originally Posted by The_Ripper

@VFL
Last thing you can do is to remove carefully DOM from receiver and then boot, if this doesnt help then USB stick isnt problem, some problem on dhcp app<->your router and getting IP address.

@The_Rippe do u have any indea how will working now! still only show VFD geeko but never show Recove mode
just boot then geeko and nothing else. :bowing-036:
22-09-2010, 09:44 AM
Carp95

@MickeySa

Can't seem to get it running on the Premium Plus.

After changing bootup nothing happens VFD just stays black

Recovery works like a charm do:respect-040:

Atteched my bootup file
22-09-2010, 10:19 AM
MickeySa

Quote:

Originally Posted by satdish101

MickeySa,
By making the change to the bootup file as you suggested (including commenting and uncommenting) using:

insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f NTSC_M -digital -f HDMI_720p60 -hdmi_chip SiI9134 0 14 15 100 0"

I am able now to get my HDMI (NTSC) to display however I do not get past the occasional spinning gears :(

If my syntax is wrong for an NTSC HDMI display please advise. If my video is properly configured, it appears that E2 is not loading?

Thank you :respect-061:

Well please press menu button and not the HOME button.

So for all people which are confused, use MENU button on RCU. NOT HOME.
22-09-2010, 10:36 AM
MickeySa

New AzBox HD Web Interface by DDamir

Please remove old interface directory and files located ( Webinterface ) located in :

Code:

/usr/lib/enigma2/python/Plugins/Extensions

Use FTP and transfer this files and If asked for overwrite press Yes .

You should have new AzBox HD Interface after You reboot your receiver.

Added: RCU of Elite and Premium/+ .

Automaticall recognition of model, so if You are running E2 on Elite You will have Elite RCU, or Premium RCU according on which model You are running E2 .

Screenshots also work now , as there is new grab file provided :)
22-09-2010, 10:39 AM
MickeySa

AzBox HD Web Interface v 1.0 by DDamir

This is ipkg, for automatic installation of Web Interface for Enigma 2 OE 1.6 AzBox HD.

NOTE: There is no need to do manual uninstall of WebIF, as this is done automatically by provided IPKG file.

Thanks to our team member DDamir :)
22-09-2010, 11:23 AM
massimo1167

Quote:

Originally Posted by MickeySa

AzBox HD Web Interface v 1.0 by DDamir

This is ipkg, for automatic installation of Web Interface for Enigma 2 OE 1.6 AzBox HD.

NOTE: There is no need to do manual uninstall of WebIF, as this is done automatically by provided IPKG file.

Thanks to our team member DDamir :)

E2 for AZbox is based on OE1.5 or OE1.6?
22-09-2010, 11:27 AM
MickeySa

Oe 1.6
22-09-2010, 12:24 PM
massimo1167

Quote:

Originally Posted by MickeySa

Oe 1.6

So do you believe that we can use in the next E2 beta release the usb DVB-T tuner with the same drivers used for dm800?

Here the collection of drivers for DE1.3.3 for DVB-T tuner:

Code:

af9015AverMedia AVerTV Volar Black HD A850.tgz ASUS My Cinema U3100 Mini DVBT Tuner.tgz Asus U3000HDream Elite TeamDIB0700.tgz AverMedia AverTV DVB-T USB 2.0 A800.tgz AVerMedia AVerTV DVB-T Volar Xaf9015.tgz AverMedia AVerTV Volar Black HD PLUS A850af9015.tgz DW21024 DVB-Sdw2102.tgz Forward Video DUTV005ce6230.tgz Freecom USB2.0 DVB-Trtl2831u.tgz Genpix SkyWalker-1 DVB-S receivergp8psk.tgz Hauppauge Nova-T Stick (70001 - 70009 - 70019DIB0700.tgz Hauppauge WinTV HVR 900em28xx.tgz Hauppauge WinTV MiniStick***usb.tgz Hauppauge WinTV Nova-TDDIB0700.tgz Hauppauge WinTV-NOVA-T usb2nova-t-usb2.tgz Leadtek WinFast DTV Dongle Goldaf9015.tgz LogiLink VG0002 V.2.0 USB DVB-T PenEC168.tgz Pinnacle PCTV 72e;Dream Elite TeamDIB0700.tgz Pinnacle PCTV 73e;Dream Elite TeamDIB0700.tgz Technisat AirStar TeleStick 2 USB DVB-TDIB0700.tgz TerraTec Cinergy T Stickaf9035.tgz TerraTec Cinergy T USB XEaf9005.tgz WideView WT-220U PenType Receiver (TyphoonFreecomdtt200u.tgz
22-09-2010, 12:49 PM
The_Ripper

@VFL
Then it's not the problem of USB stick(if you removed DOM), is there any chance you can borrow from someone (friend,colleague) some other router and try, really dont know why dhcp app<-> your router doesnt work. If this again happening to many of you then it left me to make some Update GUI app like in original FW over my FB driver, but again it will take time for this and stop me from working on driver ....
@massimo1167
Till I finish full demux part, I cant work on that now, is it posible, yes it is (just dont know how USB speed on SMP863X chips will have affect on data traffic)...
22-09-2010, 01:04 PM
wackaman

If your Router doesnt aktivate DHCP you have a chance to connect AZB vie Crossover Lan direct with your PC / Laptop.
You have to change Lan Settings to share the Connection.
Try it maybe...
22-09-2010, 01:06 PM
digihoe

Quote:

Originally Posted by The_Ripper

@VFL
Then it's not the problem of USB stick(if you removed DOM), is there any chance you can borrow from someone (friend,colleague) some other router and try, really dont know why dhcp app<-> your router doesnt work. If this again happening to many of you then it left me to make some Update GUI app like in original FW over my FB driver, but again it will take time for this and stop me from working on driver ....
@massimo1167
Till I finish full demux part, I cant work on that now, is it posible, yes it is (just dont know how USB speed on SMP863X chips will have affect on data traffic)...

Regarding VFL's problem
Is it possible to connect the Azbox directly via LAN to the computer to do the update? Will need to enable dhcp, but will eliminate new router, right?
Maybe there is a port that is blocked in firewall or router?

Regarding USB, I for one have high hopes for it to work, I think DVB-T should have the highest chance of working since it has less bandwith. Good luck on the demux driver (maybe there is a way to demux two streams at the same time?)

Best regards!
22-09-2010, 01:37 PM
wackaman

I have written here Crossover Lan connect direct AZB to PC/Laptop
22-09-2010, 01:57 PM
mauro87

The_Ripper, please tell me why line failure?
22-09-2010, 02:00 PM
mauro87

The_Ripper, please tell me why line failure sat
22-09-2010, 03:22 PM
satdish101

Quote:

Originally Posted by Carp95

@MickeySa

Can't seem to get it running on the Premium Plus.

After changing bootup nothing happens VFD just stays black

Recovery works like a charm do:respect-040:

Atteched my bootup file

Carp95,
Are you using a PAL or NTSC display? If NTSC, you might try the editing in the line I typed a few posts above. A few thoughts/suggestions. Just to confirm, to install E2 on your Premium+ you (cut and paste from prior post in this thread):

1. Load this patch.bin ( Enigma 2 ) file on FAT32 formatted USB Memory Stick
2. Turn Off Your AzBox HD Device, put USB Memory Stick inside and Turn on AzBox HD Device.
3. Follow the procedure USB Update on the screen, (patch version: 1.0.21 E2 by TheRipper, press OK, wait to finish, reboot - don't remove stick !)
4. Start AZUp , write IP adress of AZBox (see VFD), then click on Update button on AZUp, wait and follow message on AZUp and VFD, when all done - wait for reboot msg on VFD and then remove USB stick

If at all possible, can you connect a composite video cable (yellow RCA jack) to a display? I am seeing a few blinking spinning gears but this test ver. of E2 doesn't appear to be loading on Ultra. If you have installed this test version of E2 as above, its possible that your Premium+ is behaving the same but that you can't see it because the video is not configured properly.
22-09-2010, 03:24 PM
atoth73

@VFL, mauro87

You can try to setup a DHCP server on your PC/notebook instead of router and connect the AZbox and PC via crossover cable, maybe it can help also. In the past successfully tested such config. on Dreambox aswell to getting IP addresses before the flashing (DM7020, console mode)
22-09-2010, 03:53 PM
mauro87

azboxhd Premium for configurate as satellite
22-09-2010, 04:35 PM
Carp95

Quote:

Originally Posted by satdish101

Carp95,
Are you using a PAL or NTSC display? If NTSC, you might try the editing in the line I typed a few posts above. A few thoughts/suggestions. Just to confirm, to install E2 on your Premium+ you (cut and paste from prior post in this thread):

1. Load this patch.bin ( Enigma 2 ) file on FAT32 formatted USB Memory Stick
2. Turn Off Your AzBox HD Device, put USB Memory Stick inside and Turn on AzBox HD Device.
3. Follow the procedure USB Update on the screen, (patch version: 1.0.21 E2 by TheRipper, press OK, wait to finish, reboot - don't remove stick !)
4. Start AZUp , write IP adress of AZBox (see VFD), then click on Update button on AZUp, wait and follow message on AZUp and VFD, when all done - wait for reboot msg on VFD and then remove USB stick

If at all possible, can you connect a composite video cable (yellow RCA jack) to a display? I am seeing a few blinking spinning gears but this test ver. of E2 doesn't appear to be loading on Ultra. If you have installed this test version of E2 as above, its possible that your Premium+ is behaving the same but that you can't see it because the video is not configured properly.

No m8 it's pal, testing goes on tonight, think I have the problem.
As I use Winscp for FTP ( and edit ) so could be dos2unix problem.

If I get it up will test all kind off settings but the insmod clearely states hdmi
22-09-2010, 04:41 PM
mauro87

the tuner tuning configuration

:respect-040:not sorry that don't watch is to understand that I will configure the satellite antenna because I have a dual feed at 13 ° and 19 ° and are in trouble, says me impossible tuner, ah I forgot I close to dual feed two descents. Thank you
22-09-2010, 04:54 PM
genius74

What about the azbox card reader, anybody has tested it yet?
22-09-2010, 05:06 PM
satdish101

Quote:

Originally Posted by Carp95

No m8 it's pal, testing goes on tonight, think I have the problem.
As I use Winscp for FTP ( and edit ) so could be dos2unix problem.

If I get it up will test all kind off settings but the insmod clearely states hdmi

thanks. assuming you get your display issue figured out, please let us know the results on the Premium+. as I mentioned above, connecting a yellow composite video cable would be the easiest way to check the status of your install
22-09-2010, 07:59 PM
Carp95

Quote:

Originally Posted by satdish101

thanks. assuming you get your display issue figured out, please let us know the results on the Premium+. as I mentioned above, connecting a yellow composite video cable would be the easiest way to check the status of your install

First part off install is no problem I can watch progress, then AzUp also works ( in progress now) then first boot comes indeed with a 100 % in display.

Problem is adjusting the bootup file after I done that and reboot nothing happens
22-09-2010, 08:18 PM
pr2

For people that have problems to get a DHCP address from their router:

- First connect to your router and check that DHCP server is enable
- I would advice you to power off your Azbox.
- Reboot your router (so ARP cache is cleared)
- Wait for the router to come back
- Start your Azbox.

Some "bad" router can badly handle the ARP cache so they still associate the MAC address with the previous static IP.

Another good trick is to install the official firmware, set your Azbox to DHCP and write down the IP address that it receives, because during E2 installation the DHCP request it will receive the same IP from your router.

Pr2
22-09-2010, 08:25 PM
Carp95

Ok dos2unix was the problem now it boots.

boot proces

1 - upwards to 100%
2 - 8 times from around 50% to 100%

During this proces I see a few blinking spinners indeed every time it reaches 100%
3 - stays on 100%

Problem is I can't acces my HDMI setup the wife is boss, so now it's connected through scart on a old setup this doesn't clear a picture
22-09-2010, 09:08 PM
britzolas

Good evening pr2,
Since I see you navigate here, I'd like to ask you if opensat still supports the box. The upcoming E2 means that we will never see a 1.0 firmware???
I hope you answer because I think my question reflects the thoughts of all AZBox owners.
Sorry for the off-topic.
22-09-2010, 09:09 PM
satdish101

Quote:

Originally Posted by Carp95

Ok dos2unix was the problem now it boots.

boot proces

1 - upwards to 100%
2 - 8 times from around 50% to 100%

During this proces I see a few blinking spinners indeed every time it reaches 100%
3 - stays on 100%

Problem is I can't acces my HDMI setup the wife is boss, so now it's connected through scart on a old setup this doesn't clear a picture

thanks. I am seeing the same thing as you a few blinking spinning gears with both composite video output (analog) and HDMI with Ultra. Hopefully MickeySa will have suggestion.
22-09-2010, 09:21 PM
moicas3004

Quote:

Originally Posted by satdish101

thanks. I am seeing the same thing as you a few blinking spinning gears with both composite video output (analog) and HDMI with Ultra. Hopefully MickeySa will have suggestion.

My suggestion is..

Leave the guys alone and let them continue the development. Stop wasting they're time with questions on a unfinished firmware. let them finish the real thing.

@The_Ripper and Development Team

Keep up the good work guys. What i seen from this preview i have love'it.
Cant wait the put my hand on the functional firm.
22-09-2010, 09:34 PM
xanadu

Has anyone got this working with a Premium Plus?

Mine boots up, goes past the Geek & VFD on the display, then counts 12, 24, 25 in the display and stops but no output on the TV via HDMI, but has the blue and red LED showing. The remote doesn't do much either.

I can FTP no problem at all when it's booted up.

I have edited the boot file and replaced the new dvb ko file.

Any ideas?
22-09-2010, 09:42 PM
Carp95

Quote:

Originally Posted by moicas3004

My suggestion is..

Leave the guys alone and let them continue the development. Stop wasting they're time with questions on a unfinished firmware. let them finish the real thing.

@The_Ripper and Development Team

Keep up the good work guys. What i seen from this preview i have love'it.
Cant wait the put my hand on the functional firm.

Sorry m8 but these tests are a result off a post made by the team!!!!!!!!!!
Furthermore there's no presure what so ever, if they read it and have the time to answer they will.
It's not like we're holding them down

@Xanadu

Thats where I am @this point
22-09-2010, 10:36 PM
xanadu

Quote:

Originally Posted by satdish101

I am seeing a few blinking spinning gears

Looks like that's the furthest we are going to get on Premium Plus at the moment......

The furthest I have got now with the Premium Plus is with the original em8634dvb.ko.

I can get 100 on the VFD, and see cogs flashing on the TV, but with the replacement em8634dvb.ko, the VFD only counts upto 25, and nothing on the TV displayed at all.

Show 40 post(s) from this thread on one page

All times are GMT +1. The time now is 06:28 PM.