Solo 4K or Oscam and Cccam First Installation Help

Printable View

Show 40 post(s) from this thread on one page

23-05-2021, 12:44 PM
levrek

Solo 4K or Oscam and Cccam First Installation Help

There were similar topics in the forum, but I wrote my questions again because I could not fully understand.

I just bought a new Solo 4K, I was a Solo 2 user before and was using CCCam. Now I want to use Oscam. I installed the device with BlackHole 3.1.0 flash, reconfigured the channel settings with Tuner.
I wanted to download and install something from the Addons section. Solo 4K gave a green screen, so I had to reinstall BH. So I surfed the Internet and tried to find the most current versions of Oscam and cccam. Which one of these should I choose?

Current Oscams I could find:
1.enigma2-plugin-softcams-oscam.emu11595-arm_1.1-r0_cortexa15hf-neon-vfpv4.ipk

2.enigma2-plugin-softcams-oscam_11.691-emu-r798_all.ipk

3.enigma2-softcams-cccam-all-images_2.3.9-r2-RAED_OE2.0_all.ipk

Current Cccam I could find:
1. CCcam2.3.2 2019-05-07-de.arm

2.ccam info-ccam prio-oscam dvbapi-oscam services-oscam srvid-oscam srvid2 10.02.2020

By your advice, After deciding which version, first of all
I will follow the following yo is it correct?

Cccam ipk with FTP program -> var / / Temp
Oscam ipk with FTP program -> var / Temp
After I put it in the folder, I will install Solo 4K and BH with Manuel install.
Solo 4K Restart:

After I put the Cccam into the file with the FTP program, I will authorize it as follows:
CCcam.channelinfo -> / var / etc (chmod 644)
CCcam.prio -> / var / etc (chmod 644)
CCcam.providers -> / var / etc (chmod 644)
CCcam.cfg -> / var / etc (chmod 777)

Emu files: / var / bin - cccam (chmod 777)
Where to get emu files and are they required?

After I put the Oscam into the file with the FTP program, I will authorize it as follows:
Oscam.conf -> / var / tuxbox / config (chmod?)
Oscam.server -> / var / tuxbox / config (chmod?)
Oscam.user -> / var / tuxbox / config (chmod?)
Oscam.services -> / var / tuxbox / config (chmod?)
Oscam.srvid -> / var / tuxbox / config (chmod?)
Oscam.srvid2 -> / var / tuxbox / config (chmod?)
Oscam.dvbapi -> / var / tuxbox / config (chmod?)

Emu files: usr / bin / cam (chmod 755)?
Where to get emu files and are they required?

To switch between these two
An Addons Maneger program I can find: enigma2-plugin-extensions-levi45multicammanager_8.1_all.ipk with FTP program -> var / / Temp and install it.

I will convert the Ccams with cccam2oscam-1.2 and throw them into Oscam files. There are two files here, User and Server.
So will nothing be written into the other files below?
- oscam.dvbapi
- oscam.services
- oscam.srvid

Emu files: usr / bin / cam (chmod 755)?

Finally, are files like MGcamd, Camd3, Newcamd, Xcamd etc. needed?

In addition, I put my 2.5 hard drive that I removed from Solo2 into Solo 4K, there are movies in it, the device saw as HDD in the menu, do I need to re-install it again?

Thank you.
23-05-2021, 11:31 PM
echelon

A few basics for you

only arm based files should be used , especially the bin files like cccam and oscam and mgcamd

read mode is attributes 644 , read and write is 755 , , so I have no idea why you mention 777 ? I have only ever used the first 2

so you require various files for each one , ARM based bin files , camscript files, config files , so not MIPS files

OSCAM requires various files in VAR/ETC/TUXBOX/CONFIG , several , including the ones you mentioned, so each file has a use within oscam but is normally 644 , not 755

the bin file goes into var/bin and chmod to 755

the oscam script goes into usr/camscript as usual , chmod 644

mgcamd v1.46 may prove useful , along with the configs in usr/keys

your HDD needs to be added as a device, mounted , no need to install it again , just mount it as a hdd , so it is recognised by the OS

I do not have a 4K box but the principles are the same as the older VU boxes (I use openBH myself)

the openBH is now on version 4.4 , or stay on the image you downloaded above , blackhole 3.1.0 for 4k boxes
24-05-2021, 07:50 AM
levrek

Thank you for your quick response. I have never used Oscam before. So I don't know what current version I should install and how to authorize (644 now). Which of the three Oscam versions I have given above should be (arm based as I understand it) or are there any newer ones?
I wonder if CCcam2.3.2 2019-05-07-de.arm version is suitable as Cccam?

I will also try the mgcamd v1.46 recommendation after Oscam is done.

I am glad that the HDD is not reinstalled and its contents are not erased.
Thanks again
24-05-2021, 02:06 PM
levrek

I have no glass installed on my device. BH 3.1.0. Can I install the latest CCCAM and Oscam versions in Solo 4K?

CCcam2.3.2-de.arm

oscam svn11684-solo4k-emu-r798 Jan 31st 2021

Thanks.
24-05-2021, 03:13 PM
echelon

I am afraid that I cannot answer the questions about latest versions etc, as mine are MIPS based but I did my mips one last week to version r11691 after obtaining it from other forums, so try the main ones for the files , but we cannot name them on here, but there are several containing various emu files and configs and tutorials etc

sometimes only the bin file is in any zip etc , but an IPK installer may well install the camscript & configs as well as the bin file, plus setting the correct 644 or 755 for you , as a full package and not just the bin

otherwise its use flash fxp or filezilla or DCC or similar to set the attributes by FTP into the box ( I prefer flash FXP but numerous FTP programmes are out there), plus available in other linux forums or similar on here, not just this sub forum. I have used flash fxp and DCC for maybe ten to fifteen years so am set in my ways)

sometimes you can install a plugin tool that gives access to BH emus as well as for other images

your oscam config files will need editing after installation, or you can FTP them manually instead , oscam is a ball game in its own right, as explained in numerous threads on here for a decade or more , so not just a 4k box topic, but linux in general , VU , TECHNOMATE , DREAMBOX , loads of manufactured boxes

chances are that you only need to mount your HDD , plus also mount any USB stick too, if used for EPG saves etc , mine has both mounted , as hdd or usb as required
24-05-2021, 04:05 PM
hda5

1 Attachment(s)

OSCAM for vuplus zero 4K/ solo 4k/ultimo 4k/uno 4k, mutant hd51/52, AX 51/52, Xtrend, ET11000/120000, Spycat 4K, Edision 4k, Octagon 4k, DM900, DM920, Vu+ solo, Uno, Duo, Ultimo, Zero (IPK)

OpenATV, BlackHole, OpenBH, OpenLD, OpenPLi, OpenHDF, OpenVix, VTI, SatDreamGr, OpenDroid.

oscam.server
osam.conf files go in /etc/tuxbox/config

FTP the ipk file to /var/volatile/tmp

Then use the IPK install option from within Blackhole to install the oscam binary.
25-05-2021, 09:58 AM
levrek

Thank you for your Patience and attention to this newbie. I installed Oscam thanks to you. Do I need to install Ccam now as well? If your answer is yes, you better say, what current version of Cccam should it be?
25-05-2021, 10:28 AM
Mickha

Personally I prefer Oscam, but test it, before adding anything else.
Try the Softcam Concierge, provided by hda5:
SoftCam Concierge [Team Satpimps] CCcam.cfg newcamd.list oscam.server

If you need help, using the tool, please post back.
25-05-2021, 03:43 PM
levrek

Thanks, SoftCam Concierge [Team Satpimps] CCcam.cfg newcamd.list oscam.server
I downloaded it, I will try it at the first opportunity.
26-05-2021, 02:29 PM
levrek

Hello, I downloaded SoftCam Concierge [Team Satpimps] CCcam.cfg newcamd.list oscam.server.
I got a cccam line for testing from provider X, I converted the line for Oscam server with SoftCam Concierge following the installation instruction:

[reader]
label = CCcam
protocol = cccam
device = egygold.net, 1xxxx
user = 09xxxx
password = xxxxx
inactivitytimeout = 1
group = 1
cccversion = 2.1.2
ccckeepalive = 1

and sent it to solo 4K. However, I did not know how and where to process the following information given by the cccam provider.
Domain Name: egygold.net
Port: 1xxxx
Users: XXX ........
Password: XX .........

Will this information be entered in oscam.conf or oscam.user? How ?

Thanks
26-05-2021, 03:20 PM
hda5

The info will be entered into oscam.server

All the info provided by your CCcam provider is actual in your oscam.server file, look again.

Restart oscam from the Blackhole menu after transferring the files.
27-05-2021, 06:13 PM
echelon

Quote:

Originally Posted by levrek

Thank you for your Patience and attention to this newbie. I installed Oscam thanks to you. Do I need to install Ccam now as well? If your answer is yes, you better say, what current version of Cccam should it be?

You can add several emu cams if you want to, including cccam , and mgcamd 1.46 , plus the oscam listed above, then you can try them out at your leisure using the blue button to switch between them (I would suspect you need an arm version of cccam, not a mips version) , chmod the bin file to 755 if required , the config is same as before as they are just text files, like oscam or the configs for mgcamd etc

Oscam is probably the best these days, but do not discount the benefits that other emus may bring :)
28-05-2021, 09:44 AM
levrek

I feel like a problem kid. Oscam line from service provider

[reader]
label = sharing1
enable = 1
protocol = cccam
device=s1.xtra7.net,xxxxx
user = cmtk3xxxxx
password = 6xxxxx
inactivitytimeout = 30
cacheex_block_fakecws = 1
group = 1
disablecrccws_only_for = 0500: 50F000; 09C4: 000000; 098C: 000000; 098D: 000000; 0500: 030B00
cccversion = 2.1.4
ccckeepalive = 1

[reader]
label = sharing2
.......

I copied and pasted this information with DCC and oscam.server and saved it. Oscam_11.684-r798 is selected as active Cam in Solo 4K, I restart and run it again, but there is no image again. I have defined 755 as Oscam.server authorization. The / usr / camscript privilege is defined as 776.
When I couldn't get a result like this, I pasted the lines sent by the service provider to Oscam.user and Oscam.conf, but the result is still the same.
What else could restrict or prevent?
28-05-2021, 10:19 AM
levrek

I converted the oscam lines one by one to cccam and pasted it into the Ccam.config file. I ran cccam 2.3.2 as active cam and the image came up. So the lines are working. But I don't understand why I'm having problems in Oscam ...
28-05-2021, 11:21 AM
hda5

It could be that your CCcam provider does not allow connections from oscam; or the CCcam version in your oscam.server file needs to be changed to cccversion = 2.3.2

Try that and report back.
28-05-2021, 04:34 PM
levrek

The Cccam provider sent the Lines as Oscam lines.

Cccversion = 2.1.4 in Oscam.server changed to 2.3.2 on all lines. Still no image was taken.

Oscam.conf -> / var / tuxbox / config (chmod?) Hollow lines
Oscam.server -> / var / tuxbox / config (chmod 755)
Oscam.user -> /var/tuxbox/config ( chmod 755 ) hollow lines
Oscam.services -> / var / tuxbox / config (chmod 755) hollow lines
28-05-2021, 08:54 PM
echelon

check the oscam web interface and see if its showing as connected (in your browser) - oscam.conf has your details, or needs them adding

check the user config file to ensure you have set your box up as a user, such as

Code:

[account] user = levrek1a pwd = levrek2b group = 1,2,3,4,5,6,7,8,9 cccmaxhops = 2 cccreshare = 0 au = 1 umaxidle = 0
28-05-2021, 09:56 PM
levrek

Openwebif is opened with DCC and webbrowser is opened on PC. It takes normal channel views, but I couldn't find a menu with Oscam.conf information. Instead, based on the information you provided, I manually entered them into Oscam.config in FTP.
[account]
user = testxxxxx
pwd = 59xxxxxx
group = 1,2,3,4,5,6,7,8,9
cccmaxhops = 1
cccreshare = 0
au = 1
umaxid = 0

Before that, there was the following information provided by the provider:
#[global]
#disablecrccws = 1
#disablecrccws_only_for = 098C: 000000; 09C4: 000000; 098D: 000000; 1884: 000000; 1708: 000000; 1709: 000000; 0E00: 000000; 0500: 030B00; 0500: 050F000; 1811: 003311,003315; 1883: 003311; 1819 :00006D

I made both kinds of separate entries, but still could not get a video.

Thanks
28-05-2021, 10:12 PM
echelon

the files do not use your server supplied details, they are local config files for oscam , so your user file and conf file have to be set up to work

I provided you with an example of a user file, using your username , in oscam.user (not oscam.conf)

as for the openwebif, you need to look at your oscam.conf file and see what the default oscam details are, port , name and password , etc

then put your local box ip address plus that port into your web browser , add the name and password and your oscam webif should be displayed

you can check if the lines are connected in oscam webif , plus you need your box to login to your local oscam emu by adding a user (yourself) into the oscam.user file for it to work

I did post some examples on this forum a few years ago , have a look at those

here is an example of a web address for accessing your oscam webif in firefox, chrome , edge , opera , safari , or whatever browser you use

Code:

http://192.168.0.35:15090/status.html?hideidle=1

default username & password etc may be oscam & oscam , to login to the oscam webif interface panel

to repeat , these 2 items are oscam config files , nothing to do with any lines or oscam.server , so there is a lot more to setting up oscam than cccam , try looking at these examples but the bin files are mips so do not use them on a 4K box

https://www.satpimps.co.uk/showthrea...files-and-help
29-05-2021, 10:21 PM
levrek

Hello, I followed the links you provided and the other links there.
I was finally able to connect to webif via htpp and I saw the Welcome to CCcam 2.3.2 server on the screen, of course the keys had expired. I don't want to keep you busy anymore. The sample Oscam file contents that I have been browsing the internet and trying to examine are all different from each other.
I can add lines from oscam.conf and oscam.server by copy-pasting the provider information that comes to me as a test via FTP. I have no other idea about the other lines that should be, namely some lines (I hope no ads, since these lines are no longer valid)

These lines will only be added to Oscam.server as far as I understand (it does not contain information about Oscam.conf, I think manually disablecrccws_only_for part will be added to Oscam.conf):

[reader]
label=sharing1
enable = 1
protocol=cccam
device = s1.xtra7.net, xxxxxx
user=cmtk333745
password=669753
inactivitytimeout = 30
cacheex_block_fakecws = 1
group = 1
disablecrccws_only_for = 0500: 50F000; 09C4: 000000; 098C: 000000; 098D: 000000; 0500: 030B00
cccversion = 2.1.4
ccckeepalive = 1

[reader]
label=sharing2
enable = 1
protocol=cccam
device = s2.xtra7.net, xxxxxx
user=cmtk333745
password=669753
inactivitytimeout = 30
cacheex_block_fakecws = 1
group = 1
disablecrccws_only_for = 0500: 50F000; 09C4: 000000; 098C: 000000; 098D: 000000; 0500: 030B00
cccversion = 2.1.4
ccckeepalive = 1

[reader]
label=sharing3
enable = 1
............

or test lines from another provider:

There are both oscam.server and oscam.conf lines here.

also into oscam.conf
#[global]
#disablecrccws = 1
#disablecrccws_only_for = 098C:000000; 09C4: 000000; 098D: 000000; 1884: 000000; 1708: 000000; 1709: 000000; 0E00: 000000; 0500: 030B00; 0500: 050F000; 1811: 003311.003315; 1883:003311; 1819 : 00006D
I glued

I think webif will be added here manually.
Will it be added in other lines?

also into oscam.server
[reader]
label = Server1
protocol = cccam
device = svip1.cccams.net, xxxxxx
user = swiptest17
password = 29xxxxxx
inactivitytimeout = 30
group = 1
cccversion = 2.0.11
cccmaxhops = 1
ccckeepalive = 1
audible = 1
disablecrccws_only_for = 098C:000000; 09C4: 000000; 098D: 000000; 1884: 000000; 1708: 000000; 1709: 000000; 0E00: 000000; 0500: 030B00; 0500: 050F000; 1811: 003311.003315; 1883:003311; 1819: 00006D
disablecrccws = 1

[reader
label = Server2
............
After entering these incoming lines into Oscam.conf and Oscam.server, will the remaining Oscam.user remain empty, that is, will not a line be written in it?

I will download the most up-to-date ones for the following from the internet and manually update them via FTP instead of the existing ones. Is it true?
oscam.services
oscam.srvid
Oscam.srvid2
oscam.dvbapi
sofcam.key
constant.cw
................................. ............
I do not have Ncam__Oscam installed. Does it pose a problem?

Show 40 post(s) from this thread on one page