Dummies guide to setting up Uno
Dummies guide to setting up Uno by Lee Goldwafers.com
1. Install image.
Download a USB image file, eg Blackhole Image from :-
https://www.satpimps.co.uk/forumdisplay.php?f=645
or
https://www.satpimps.co.uk/forumdisp...ack-Hole-Image
When you download a new USB image file you may find the folder names in the ZIP/RAR archive are incorrectly labeled.
So what you need to do is make a folder on your USB Pen drive called vuplus
Then inside the vuplus folder you make another folder called uno
So now you should have a folder in on your PEN drive root like this
vuplus/uno
Copy the 3 Image filenames below from the ZIP/RAR achive to the vuplus/uno folder on your PEN Drive.
boot_cfe_auto.jffs2
kernel_cfe_auto.bin
root_cfe_auto.jffs2
Power Off Uno
Insert USB Pen Drive in the front USB socket.
Power on Uno
The display window will show "press ch-" on the receiver to start flash.
Press the ch- button on the front of the receiver within 10 seconds or else the receiver will boot as normal.
Wait until display window displays "Remove USB Stick" then remove stick and power off and on to reboot the receiver.
2. Network
Connect an Ethernet LAN cable from your router to your Vu+ Ethernet port.
Press Menu
Select Set Up Press OK
Select System Press OK
Select Network Press OK
Select Network Wizard and press OK.
3. Setup Motorised Dish using USALS
First get your longitude & latitude info from _http://www.satsig.net/maps/lat-long-finder.htm
Enter your post code into satsig.net and you'll get the correct LON & LAT info for your location.
Example if I enter the following UK postal code: SE1 6JZ into _http://www.satsig.net/maps/lat-long-finder.htm
I get the following LON & LAT:
Longitude: -0.1042°
WEST
Latitude: 51.4979°
NORTH
Press Menu
Select Setup Press OK
Select Service searching Press OK
Select Tuner configuration Press OK
Select Tuner A Press OK
Configure Tuner for Motorised Dish using USALS.
Use the < > buttons on remote to select Simple.
Use the down button to select mode and use the < > buttons to set to Positioner.
Configuration Mode: Simple
Mode: Positioner
Longitude: 0.104 (Make sure you enter your own Longitude settings here)
WEST
Latitude: 51.497 (Make sure you enter your own Latitude settings here)
NORTH
Press OK to save.
Press Menu
Select Setup Press OK
Select service searching Press OK
Select Positioner Setup Press OK
Select goto 0 Press RED Button
Dish should now goto 1w.
4. Upload a Channel List
Download a pre-configured channel list example catseye's from
https://www.satpimps.co.uk/forumdisp...gma-2-Settings
Unzip the Channel List to your local HDD.
Example C:\Catseye E2 Settings File 75 East-58 West
Use VuCC to upload channel list to Uno.
VUCC is an essential tool to have.
Download VuCC From
https://www.satpimps.co.uk/showthrea...ol-Centre-V0-8
http://img847.imageshack.us/img847/2535/vucc041.jpg
5. Install Cam
Download CAM TGZ file from
https://www.satpimps.co.uk/showthrea...le-Image-EMU-S
or
https://www.satpimps.co.uk/showthrea...e2-emus-(2013)
ideally use the cccam v2.30 to avoid problems
FTP the cam-filename.tgz to the /tmp folder on Vu+
Press Green Button then Yellow Button on Vu+ remote control.
Select Manual Install Bh Package.
Select the cam-filename.tgz file and press OK.
Message will appear - Do you want to install cam-filename.tgz
Select "Yes" and press OK.
Message will appear - Installed.
Press the exit button on remote a couple of times to come out of all the menus.
6. Activate Cam
Press the Blue button and use the < > buttons on remote to select the CAM
Press OK to run the CAM.
the cccam cfg file is located in var/etc after the correct cam emu has been installed
( On E2 Boxes the 3C.config is Located at /etc with Attributes set to 755 or All config files can be found in /etc )
These instructions are for Blackhole Image other images button configurations might be slightly different.
How to setup Vu+ with VBox II DiSEqC 1.2 Positioner.
If your VBox II already has the satellite positions stored and your changing from an old receiver to Vu+ then follow this procedure.
Write down your VBox II satellite position numbers. These are the numbers displayed on the front of the VBox II when moving to a
specific satellite position. These position numbers can also be found in your old receivers motor setup menu.
Example lets say...
Position 1 on VBox II = Astra 19e
Position 2 on VBox II = Eutelsat W2 16e
Position 3 on VBox II = Hotbird 13e
You get the idea...
First send the dish to Astra 19e using Vbox II.
On Vu+ Remote Press Menu
Select Setup Press OK
Select Service Searching Press OK
Select Tuner configuration Press OK
Select Tuner A Press OK
Now set Configuration Mode to Advanced. Use Left or Right keys on remote to select.
Configuration Mode: Advanced
Satellite: Astra 19e
LNB: 1
DiSEqC mode: 1.2
Scroll down to botton of the page with the down arrow on remote.
Use USALS for this sat: No
Stored position: 001
Press OK to store.
OK that's Astra 19e setup now to setup Eutelsat W2 16e
Now send the dish to Eutelsat 16E using Vbox II.
Select Setup Press OK
Select Service Searching Press OK
Select Tuner configuration Press OK
Select Tuner A Press OK
Configuration Mode: Advanced
Satellite: Eutelsat W2 16e
LNB: 2
DiSEqC mode: 1.2
Scroll down to botton of the page with the down arrow on remote.
Use USALS for this sat: No
Stored position: 002
Press OK to store.
OK that's Eutelsat W2 16e setup now to setup Hotbird 13e
Now send dish to Hotbird using Vbox II
Select Setup Press OK
Select Service Searching Press OK
Select Tuner configuration Press OK
Select Tuner A Press OK
Configuration Mode: Advanced
Satellite: Hotbird 13e
LNB: 3
DiSEqC mode: 1.2
Scroll down to botton of the page with the down arrow on remote.
Use USALS for this sat: No
Stored position: 003
Press OK to store.
You get the idea, now repeat for the rest of the satellites and your done.
This is enough to get you started, the fun starts learning the rest.
Regards
Lee.
ps:-
TSPanel install help here:-
https://www.satpimps.co.uk/showthrea...alling-TSpanel
