if its a rar or zip file, use 7zip to extract the files
an ipk is ftp to var/tmp and installed from the box user menu (the ipk installer option)
if its a rar or zip file, use 7zip to extract the files
an ipk is ftp to var/tmp and installed from the box user menu (the ipk installer option)
i alo cannot install keep getting error messages cannot over write ,and others .tried vuzero4k factory reset,without restore settings ,but find 4 different oscam settings are still there and cannot be removed,and work with lines ????????????????????
tried loaded that levi45 file and loaded the oscam emu mips from it. Everything went ok until I tried to start it. It wouldn't!
I guess I must have a bad file somewhere. I think a fresh complete image install required.
Is the file you're trying meant for an Arm receiver, or just for the mips receivers?Originally Posted by JOE.MADDISON
Tried a factory rest,box went off now stuck with vu on tv screen,remote does nothing,tried to reflash openvix, but will not, front of box flashing,is there a vuzero4k factory reflash or does box have to go back,it has been doing strange things in the last few days
You could try and a different image such as openatv and see if that kicks the box back into life.....
You can try the original image, from the vuplus website:
Code:http://code.vuplus.com/
Alternatively I'll upload the Black Hole image, for the Zero 4K, which you can try, it'll take a few minutes.
https://www.satpimps.co.uk/showthread.php?177907-Black-Hole-3-0-6
Last edited by Mickha; 19-10-2018 at 06:48 PM.
brain cells must be going,when updating the vuzero4k using usb....box off ...usb in ..box on ...box front ..flashes dimlyslowly ....then bright flashing. but box wont work untill usb is removed... now starting from scratch and scanning sats,,then hope the reset has cleared out the old oscam files.
Here is a link to pur-e2 images. Very nice looking images.
http://pur-e2.club/OU/images/index.php?dir=6.2/vuplus/
Well i've done that, and I still can't get the oscam emu ipk to load normally, and if using levi45 it won't start,
I suppose the next step is to try another image Any suggestions which to use for AFN?
You could try openatv or pur-e2 or even blackhole. There are loads of images though and its choice. I don't hear many using what I use pure-e2 but I think it looks even better that openatv.
Last edited by kegnkiwi; 19-10-2018 at 07:15 PM.
Found the same oscam emu ipk file on another site and this one works.......
So have you got afn working. Oh and to just make it interesting there is an even newer version of oscam out late today. Its is rev 773 and has hash mode 17 and 18 which i guess is for people in the far east.
Last edited by kegnkiwi; 19-10-2018 at 09:43 PM.
I’ll have to do some reading on this guys sounds very interesting indeed
Yes, that's the one i've got. Everything working fine.
Thanks for your help.
I had a similar problem to Satcat although with VTi.
The solution was to use the 'Install IPK with force over-write' item from the software management menu.
Very interesting I wast reading about what u have just sed on an very interesting inter site about the same subject actually very interesting indeed very educational for this fantastic hobby
Wow thanks simon!
re post 94 above (Fransat) I gave it a go without success but it prompted me to dump VTi in favour of OpenATV which I prefer and which retains the CI+ facility of VTi. Oscam PV set up again after overcoming ATV's oddball approach to oscam file locations through editing /etc/oscam.emu to point to the usual place.
Thanks again
JK
Those chinese stb bit slow off the mark with afn this time.
Posting Permissions
Reply With Quote
Bookmarks