which I have now explained twice
check the path I mention for openvix, its not the same as the other images
and make sure you chmod the new file to 755
and restart enigma2 when completed
which I have now explained twice
check the path I mention for openvix, its not the same as the other images
and make sure you chmod the new file to 755
and restart enigma2 when completed
ok is the port number very important
the port number and box ip will allow u to access oscam webif and turn off stream relay..
the port number can be changed so different people may use a different port number
as doods says, to access the webif you use the ip address and port number in your browser address bar
this is all standard oscam practice, nothing to do with powervu
Done as told, but I Still can't see stream relay in webif.
Does one of the mentioned Oscam EMU-versions also work with VU+ VTi?
Not the pli one bud...lolDoes one of the mentioned Oscam EMU-versions also work with VU+ VTi?
Doods. When I overwrite my oscam file with the one you posted (oscam_1.20-rev-11198-oe2.0-emu.rar), and restart my box, in webif it still shows my original oscam file which is oscam ymod1856.
So I must be doing something wrong.
As I mentioned before, I'm on VIX.
This is what I see in webif:
OSCAM ymod1856 build #0
STATUS CONFIGURATION READERS USERS SERVICES FILES FAILBAN SCRIPT SHUTDOWN
Global Loadbalancer Camd3.3 Camd3.5 Camd3.5 TCP Newcamd Radegast Cccam Anticascading Monitor Serial DVB-Api
Last edited by Satcat; 14-01-2016 at 04:28 PM.
you will still see that version until you edit in /etc/init.d/softcam.oscam (then edit version number)
You have just ovwe writted the bin file..nothing else will change from before.
oscam Y mod is completely different and installs itself in etc/tuxbox
1)Download normal oscam from your image feed
2)Over write with one of the binary/bin files provided
3)setup your oscam.conf (Ip address range and port)
4)put softcam.key in etc/tuxbox/config/oscam
5)Start oscam
6)now type box ip plus the port from oscam.conf in your browser as so.... 192.199.0.1:8899
7)now you should have oscam webif..click config/stream relay/Mode (disable to use direct dvbapi decryption) 0 - disabled use DVBAPI
8)move to 4W and test it out...
Regards
Sat keep trying matey..I had to ponder a while before i found stream relay too but once i did everything else fell in to place
Some versions of the emu seem to have it missing...
:mofo:
as doods has said, its not oscam ymod we are talking about here, its an ordinary oscam installation, where the bin file is replaced and possibly changes made to configs and the webif commands
as I said earlier, all these issues appear to be lack of knowledge about oscam, whereas this thread is really about powervu
I think I will split it so that the oscam issues are in a separate thread
its also appears that there has to be demarcation on the image installed in the box, so can be pointless talking about it if the person using it like doodz uses openpli and others are using openvix or openatv or openvti or blackhole
people have to bear in mind the type of image installed AND the type of oscam installed as well, plus the actual location of the oscam bin file as it varies as I said in an earlier post on page 1
the default is openpli 4 image using a standard oscam installation where the bin file resides in usr/bin
not openvix using oscam_ymod
nb:- I have closed the powervu chat thread for now to prevent any oscam issues being posted in it
These files loaded with oscam ymod. When I delete oscam ymod do I leave there files? they are in etc/tuxbox/config
Untitled.jpg
no bud,leave oscam y mod completely alone..there should be another folder labelled /etc/tuxbox/config/oscam
oscam y mod should be in /etc/tuxbox/config
In openpli..
Tomorrow for any openpli user i will create a very nice working backup for solo2 if anyones interested..
Cheers
In openvix my oscam ymod is in usr/softcams. I put it is tmp first then installed it via "install local extensions" and it ended up in usr/softcams.
All my oscam files ended up in etc/tuxbox/config.
I would say its either start again , so no oscam bin file in usr/bin and no files in var/etc/tuxbox/config either
then do a full oscam install that installs both the bin file, the camscript (if its required) and the files in config
OR
you amend everything to suit
as you are learning, I would delete the oscam bin file (after backing it up to pc) and same for the config files (again after backing them up) and then a clean sheet full install of the full emu, using a standard emu (not ymod)
then ftp the powervu oscam bin file to usr/bin for openpli or usr/softcams for vix and chmod it to 755, ensuring its the same name as the old oscam name used
then amend the oscam config files by ftp them to the laptop, amend with notepad plus and then ftp them back to var/etc/tuxbox/config
also note that I have already stated that the paths are not the same in openvix , nor are they the same for oscam-ymod
doodz is basing his comments on it working using openpli , not vix , not bh , not anything else
Hi there having trouble with this what file do i overwrite with what i have downloaded from here Capture.PNG
i am using a VU solo2 with blackhole 2.1.6
Thanks in advance
Last edited by dave13142; 14-01-2016 at 11:08 PM.
you would overwrite the bin file in var/bin using an e2 patched oscam (for powervu)
those files shown in your pic are config files and need editing with notepad plus on your laptop and ftp back to the same locations
Bookmarks