Results 1 to 11 of 11

Thread: AZ Elite and jtag

  1. #1
    V.I.P Dig Deep's Avatar
    Join Date
    Nov 2006
    Location
    Stockholm
    Posts
    801
    Thanks
    0
    Thanked 0 Times in 0 Posts

    AZ Elite and jtag

    Tested everything else, no joy

    So it is time to go to the root:respect-054: abd revive this box.

    Anyone tried it ? Any ideas or tips before I start ?

    Been doing some reading so I think it will be a not so easy thing but what the heck, I donīt need it just to collect dust:hurray:

  2. #2
    Junior Member digitaly's Avatar
    Join Date
    Dec 2004
    Location
    London
    Posts
    24
    Thanks
    0
    Thanked 0 Times in 0 Posts
    You need an TTL adapter... have you screw it up? was it with telecrap azup?

    Well try to follow "RecoverAzbox" from Prg and Hectore and you will be on legs again..

    It saved me many times"!!!
    Just read carefull where the contact rx to tx tx to rx goes from you TTL adapter to your azcrapbox. as it is a common mistake to make.

    Good luck ;-)

  3. #3
    V.I.P Dig Deep's Avatar
    Join Date
    Nov 2006
    Location
    Stockholm
    Posts
    801
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Yes, I tried that. No joy so next step will be a jtag.

  4. #4
    V.I.P
    Join Date
    Jun 2008
    Posts
    331
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by Dig Deep View Post
    Tested everything else, no joy

    So it is time to go to the root:respect-054: abd revive this box.

    Anyone tried it ? Any ideas or tips before I start ?

    Been doing some reading so I think it will be a not so easy thing but what the heck, I donīt need it just to collect dust:hurray:

    i tried and failed...maybe you will have better luck. The elite has a jtag header, so there wont be much soldering needed on the board. just the shorting of two solder points for "jtag enable" . I dont know anyone who succeeded with elite, a couple of us got openocd to see the box but could never get the box to HALT.

  5. #5
    V.I.P Dig Deep's Avatar
    Join Date
    Nov 2006
    Location
    Stockholm
    Posts
    801
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Yes, I noted the enable jtag pins so that will be sorted.
    Been reading from a few russian sites so I feel prepared (lol)

    I will report later on about my problems or success

  6. #6
    Verified Registered User
    Join Date
    Jan 2011
    Posts
    82
    Thanks
    0
    Thanked 0 Times in 0 Posts
    it will halt but you will need to be fast with the keyboard to stop it,i have done 4
    premium + recivers and one of them would not halt so i unplug the usb and pluged it
    back in and that done it.

  7. #7
    V.I.P Dig Deep's Avatar
    Join Date
    Nov 2006
    Location
    Stockholm
    Posts
    801
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Thankīs for the tip
    I know You have to be on Yours toes

  8. #8
    V.I.P
    Join Date
    Jun 2008
    Posts
    331
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by iq180 View Post
    it will halt but you will need to be fast with the keyboard to stop it,i have done 4
    premium + recivers and one of them would not halt so i unplug the usb and pluged it
    back in and that done it.
    i think you are confusing enterring CRL-C in serial port to get to YAMON prompt.
    We are referring to using the JTAG port where we are trtying to put the CPU in HALT state.

  9. #9
    Verified Registered User
    Join Date
    Jan 2011
    Posts
    82
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by happyhammer View Post
    i think you are confusing enterring CRL-C in serial port to get to YAMON prompt.
    We are referring to using the JTAG port where we are trtying to put the CPU in HALT state.
    you can halt the cpu with yamon prompt, if you were in the US i would say mail it to me and i would fix it but that is not the case, it would cost more to
    ship it than the cost of a new box, but if i can help let me know.

  10. #10
    V.I.P
    Join Date
    Dec 2010
    Posts
    757
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Obviously, you could, m8... if you were to share the detailed info (and files, if necessary) with us...

  11. #11
    Verified Registered User
    Join Date
    Jan 2011
    Posts
    82
    Thanks
    0
    Thanked 0 Times in 0 Posts
    for all the hd azboxes stuck in booting or loading before you try to jtag your reciver try this first, load firmware 0.9.5020 or older on a clean usb stick
    format in fat 32 now turn off your azbox with the power switch now put the usb in the azbox now hold down the menu button on the reciver and turn on
    the power switch and keep holding the menu button until you see rescue mode, if you can get to rescue then you can load the firmware and recover your azbox
    i dont know the reasion the older firmware works but it does work most of the time for me, so give it a try before you jtag your reciver.

Similar Threads

  1. JTAG - anyone get it to work fully? (technical discussion)
    By happyhammer in forum AZBox HD Newbie Questions
    Replies: 60
    Last Post: 13-10-2013, 12:39 PM
  2. Enigma 2 - AZBOX HD
    By hfmls in forum AZBox HD Newbie Questions
    Replies: 1918
    Last Post: 08-05-2013, 09:54 PM
  3. Elite canīt read the USB
    By Dig Deep in forum AzBox HD E2 Newbie Questions
    Replies: 28
    Last Post: 06-04-2011, 06:52 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •