Page 1 of 2 12 LastLast
Results 1 to 20 of 21

Thread: Need Help setting up smargo on DM800

  1. #1
    Senior Member chris2005's Avatar
    Join Date
    Nov 2008
    Posts
    140
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Need Help setting up smargo on DM800

    Hi all

    I have a smargo card reader which i want to set up on my box but I am having no luck.

    I have settings for smargo set toautoswitch and dreambox then clicked apply and it said writing succesful so I think that parts right.

    I have these lines in my cccam cfg.

    SERIAL READER : /dev/usb/tts/0 smartreader+
    SMARTCARD CLOCK FREQUENCY : /dev/usb/tts/0 3570000
    BOXKEY: /dev/usb/tts/0 xx xx xx xx

    I am using the latest dream elite image.

    Regards

    Chris2005

  2. #2
    Black Hole Team sonic1's Avatar
    Join Date
    Dec 2004
    Location
    Kernow
    Posts
    4,838
    Thanks
    7
    Thanked 7 Times in 1 Post
    Then you should have read this post.

    https://www.satpimps.co.uk/showthread.php?t=130699

    You are using IE 1.6

  3. #3
    Senior Member chris2005's Avatar
    Join Date
    Nov 2008
    Posts
    140
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Hi sonic

    I have put the right lines in my cccam cfg but it keeps saying no or unknown card inserted.

    when I plug smargo into dreambox the green led comes on but when I put card in the led goes off.

    Is there someting I am not doing right

    Thanks

  4. #4
    Black Hole Team sonic1's Avatar
    Join Date
    Dec 2004
    Location
    Kernow
    Posts
    4,838
    Thanks
    7
    Thanked 7 Times in 1 Post
    Which version of firmware are you using on the smargo ?

    And is it set for dreambox mode or normal ?

    From memory you now need to switch it back to normal with OE 1.6

  5. #5
    Senior Member chris2005's Avatar
    Join Date
    Nov 2008
    Posts
    140
    Thanks
    0
    Thanked 0 Times in 0 Posts
    when I go to smartreader and click on misc it says smartreader version v1.0.0.2

    when i open the smargo v1.4 updater it says found smartreader on com10 then it comes up uplug and plug smartreader I do that then after a while the loader bar goes to 100% but when I check smartreader it says version v1.0.0.2

    Confusing:001_07:

  6. #6
    V.I.P Giga's Avatar
    Join Date
    Feb 2009
    Posts
    4,161
    Thanks
    0
    Thanked 0 Times in 0 Posts
    why would you update to 1.4, is pulled from official website as problematic stay on 1.3

  7. #7
    Senior Member chris2005's Avatar
    Join Date
    Nov 2008
    Posts
    140
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Hi Giga

    Thanks for the reply

    I have been trying to update the smargo all day to v1.4 and v1.5 with no luck.

    Tried v1.3 and first time updated successfully, Things are looking up

    Hopefully now it will work in the dm800

  8. #8
    Senior Member chris2005's Avatar
    Join Date
    Nov 2008
    Posts
    140
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Still no joy

    I have pressed yes at device manager for smargo
    I have put boxkey in cfg
    And put these lines in cfg

    SERIAL READER : /dev/ttyUSB0

    SMARTCARD CLOCK FREQUENCY : /dev/ttyUSB0 6000000

    BOXKEY : /dev/ttyUSB0 01 02 03 04

    SMARTCARD SID ASSIGN : /dev/ttyUSB0

    Does this look right

  9. #9
    V.I.P Giga's Avatar
    Join Date
    Feb 2009
    Posts
    4,161
    Thanks
    0
    Thanked 0 Times in 0 Posts
    check that smargo is on USB port 0 with dmesg when you connect smargo without card after 20 seconds issue this command or simular on your box.
    tdi_sio 1-1:1.0: FTDI USB Serial Device converter detected
    drivers/usb/serial/ftdi_sio.c: Detected FT232BM
    usb 1-1: FTDI USB Serial Device converter now attached to ttyUSB#
    where # would be the USB port

  10. #10
    Verified Registered User
    Join Date
    Dec 2004
    Location
    Glasgow, Scotland
    Posts
    129
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Hi Guys,

    Sorry to jump into someone else's thread, but I have the exact same problem. Been using Nabilo BH 12 for some time, and decided to upgrade to Dream Elite 1.3.3. It's working perfectly, but it won't recognize my Smargo. I went back to BH12 just to check, and it's working fine there. When I go to Dream Elite, I get "no or unknown card inserted" even though I have changed the cfg file setting to SERIAL READER : /dev/ttyUSB0. I'm not too sure what firmware is on the Smargo, but it is working with BH 12.

    GAH

  11. #11
    Verified Registered User
    Join Date
    Dec 2004
    Location
    Glasgow, Scotland
    Posts
    129
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Hi Guys,

    Quick update to confirm that you do need to change the kernel setting on the Smargo from "DreamBox" to "Normal" as Sonic1 suggested. Once I did that, and re-connected the Smargo to the Dreambox, it worked perfectly after a re-start.

    GAH

  12. #12
    Senior Member chris2005's Avatar
    Join Date
    Nov 2008
    Posts
    140
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Hi Giga

    Theres a whole list of stuff that comes on screen when I type the Dmesg command but I cant see anything for the smargo.
    Last edited by chris2005; 13-06-2010 at 07:58 PM. Reason: SPELLING

  13. #13
    V.I.P Giga's Avatar
    Join Date
    Feb 2009
    Posts
    4,161
    Thanks
    0
    Thanked 0 Times in 0 Posts
    if you disconnect the smargo card reader from your dreambox, boot up dreambox an let it settle, then connect the smargo card reader wait a little again, it should be the last lines if smargo was detected.
    do a dmesg > satpimps.txt you should then find then satpimps.txt in folder root. FTP it from your dreambox to your computer and use word processor to search for USB.
    [ 3.012570] usbcore: registered new interface driver usbfs
    [ 3.012703] usbcore: registered new interface driver hub
    [ 3.012827] usbcore: registered new device driver usb
    [ 3.032457] USB Universal Host Controller Interface driver v3.0
    [ 4.958900] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
    [ 4.959060] uhci_hcd 0000:00:1f.2: irq 19, io base 0x0000ef80
    [ 4.959367] usb usb1: configuration #1 chosen from 1 choice
    [ 4.959493] hub 1-0:1.0: USB hub found
    [ 4.959574] hub 1-0:1.0: 2 ports detected
    [ 5.060367] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
    [ 5.060448] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 5.060529] usb usb1: Product: UHCI Host Controller
    [ 5.060587] usb usb1: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
    [ 5.060647] usb usb1: SerialNumber: 0000:00:1f.2
    [ 10.092300] usbcore: registered new interface driver usbserial
    [ 10.092416] usbserial: USB Serial support registered for generic
    [ 10.092530] usbcore: registered new interface driver usbserial_generic
    [ 10.092593] usbserial: USB Serial Driver core
    [ 10.170844] usbserial: USB Serial support registered for FTDI USB Serial Device
    [ 10.170989] ftdi_sio 1-2.4.4:1.0: FTDI USB Serial Device converter detected
    [ 10.171103] ftdi_sio: Detected FT232BM
    [ 10.171239] usb 1-2.4.4: FTDI USB Serial Device converter now attached to ttyUSB0
    [ 10.171338] usbcore: registered new interface driver ftdi_sio
    [ 10.171400] ftdi_sio: v1.4.3:USB FTDI Serial Converters Driver
    [ 317.096850] usb 1-2.4.2: new full speed USB device using uhci_hcd and address 5
    [ 317.212075] usb 1-2.4.2: configuration #1 chosen from 1 choice
    [ 317.216964] ftdi_sio 1-2.4.2:1.0: FTDI USB Serial Device converter detected
    [ 317.217103] ftdi_sio: Detected FT232BM
    [ 317.217244] usb 1-2.4.2: FTDI USB Serial Device converter now attached to ttyUSB1
    [ 317.221371] usb 1-2.4.2: New USB device found, idVendor=0403, idProduct=6001
    [ 317.221471] usb 1-2.4.2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
    some USB information should show, if not there is a problem with installation or hardware?
    Don't you need to enable FTDSIO on some control panel or install drivers in dream elite image? don't have this info, sorry.
    Last edited by Giga; 14-06-2010 at 07:27 AM.

  14. #14
    Junior Member
    Join Date
    Oct 2005
    Posts
    14
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Yes you need to install drivers via blue button in dream elite.
    I have 4 smargos connected to dm800 with latest dream elite image and all worked straight away "out of the box" once drivers loaded.

  15. #15
    Senior Member chris2005's Avatar
    Join Date
    Nov 2008
    Posts
    140
    Thanks
    0
    Thanked 0 Times in 0 Posts
    I have went to blue button kernel modules manager then selected yEs for
    smargo and other usb cardreaders chipset ftdi.

    Its the only thing I can see in that section is this the driver for the smargo?

  16. #16
    Junior Member
    Join Date
    Oct 2005
    Posts
    14
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by chris2005 View Post
    I have went to blue button kernel modules manager then selected yEs for
    smargo and other usb cardreaders chipset ftdi.

    Its the only thing I can see in that section is this the driver for the smargo?
    thats the one I selected.
    Dont forget as others have stated smargo needs to be in normal mode not dreambox mode

  17. #17
    Senior Member chris2005's Avatar
    Join Date
    Nov 2008
    Posts
    140
    Thanks
    0
    Thanked 0 Times in 0 Posts
    I,ve got the feeling my smargo is faulty, so I ordered a new one.

    we will see how it operates when it arrives :o16:

  18. #18
    Black Hole Team sonic1's Avatar
    Join Date
    Dec 2004
    Location
    Kernow
    Posts
    4,838
    Thanks
    7
    Thanked 7 Times in 1 Post
    Make sure you get one from the board sponsor, places like fleb@y are full of fakes.

  19. #19
    Senior Member chris2005's Avatar
    Join Date
    Nov 2008
    Posts
    140
    Thanks
    0
    Thanked 0 Times in 0 Posts
    I will do, the old one for some reason is completely dead the green light is on but when put into pc it does not even see it.

    It will be going cheap on Fleabay when I get my new one if anyone is interested ( only joking )

  20. #20
    Senior Member chris2005's Avatar
    Join Date
    Nov 2008
    Posts
    140
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Got the new smargo today Plugged it into the dreambox and it worked first time,

    As sonic says make sure you get a genuine product it will save you time and money which I learned the hard way :respect-055:.

Page 1 of 2 12 LastLast

Similar Threads

  1. DM800: Smargo + Mbox + N2 issues...
    By goran in forum Dreambox DM800HD
    Replies: 0
    Last Post: 03-02-2010, 06:26 PM
  2. EDG-Nemesis 1.0 RC1 HD for DM800
    By kegnkiwi in forum Dreambox DM800HD
    Replies: 1
    Last Post: 28-04-2009, 09:13 AM
  3. DM800 and 10/1 Diseqc set-up problem.
    By Dkstyle in forum Dreambox DM800HD
    Replies: 6
    Last Post: 15-01-2009, 10:50 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •