I have installed OoZooN DM800HD 080614 in the box and BarryAllen, gemini2-360 and NabiloBlackHole in usb flash mem
I got the box yesterday have not got clue what I am doing can someone tell me step by step what I have to do and download and where to put it to get it working please I have looked around the internet but nothing is making sense to me
All the best Dean.
In gemini press the "blue" button on your remote --> addons --> download & install.
Thanks but install what
All the best Dean.
Here's a set-up procedure that I've copied and pasted from sleepy on another forum, all credit to sleepy, hope this helps.Originally Posted by Dean sat
1. Unpacked the dreambox
2. Plugged it in (including network cable to router or PC) and went thru the initial setup (probably dont need this step!!)
3. Turned off the box at the wall and held in the power button on the box, then switched back on at wall, to get into a mode to load new firmware
4. The oled on the front shows **BOOT** and an ip address.
5. Fire up a web browser and enter http://<ip shown on db>
6. This takes you into a web page where you can click to load new firmware.
7. browse to where your new firmware image is (I downloaded and LOVE the latest Gemini image)
8. Click on load/go and thats it - sit back for a couple of minutes till status bar on web page shows "complete"
9. Press the power button on your DB this will restart your box and load the new Gemini firmware with a CLASS looking boot screen.
10. Go thru initial setup (as per original image)
11. Here you can either scan satellites, or cancel and load settings from the gemini server (blue button)
12. After initial setup I pressed the BLUE button on the remote - then choose addons and selected gemini server.
13. This gives you access to softcams and all sorts. All I needed was Cccam, so choose this, and it installed.
14. FTP'd a cccam.cfg to my box (usual place /var/etc) then off I went.
Once you run thru the initial setup - press the GREEN button and choose "Software update" - this will install the latest dvb drivers
That's great advice guys, I am just awaiting my network access point and USB stick, I guess before I install anything on the USB stick, I've guess I've got to format it using Fl**hWiz**d?
I couldn't get Fl**hWiz**d to work with the DB800
I used DCC to fire Barry Allen accross as a plug-in, then used barry Allen to sort the USB stick.
Hope this helps.
I see from time to time how new DM800 users make a difference between Enigma(2) and inofficial images...ALL images are Enigma(2), the inofficial images are simply customized versions by different teams.
Im using Gem. Enigma Image -- I have a C line I need to FTP to box -- But dont see cccam.cfg in /var/etc Do I create one?
No you go to Blue Panel > Addons and Configs then download CCam config file.
I have done all this again & again but still black screen on prem***
What am I doing wrong ???
When I restart the splash screen with the gp2 logo still says loading enigma once the blue panel has finished boot. Is this correct or do i need to do something else.
Please Help !!!
"I used DCC to fire Barry Allen accross as a plug-in, then used barry Allen to sort the USB stick." How do I do this? Which folder do you put the plug-in in to then use DCC?
Still cant get my stab motor to move!!
Can the 800 be made to work with gfox2.1? Also got a 7020 on which it works.
Getting there now but how do i get my C line?
I'm Trying to Flash an Image to my mates box and i'm not getting anywhere my head is a shed:001_07: I followed this to do list and everything went fine up to point 6....here i ended up at a page that said..... 'Dream Box Webbrowser TV'...or something similar and a row of selections like...TV.......Radio.......Films ....Web TV.....etc.
I had no option to do anything...Has anyone any Idea were iv'e gone wrong please?
rgds.Tryharder
looks like you let the dreambox bootup instead of holding in the little button near the front oled when you first switch it on
once you have done this , you will get some details i,e BOOT , and an ip address so write that ip down
now put that IP into your web browser after http:// and you will get the loading screen on your pc ( assuming you are connected by ethernet through a router )
then you browse to the file as per the instructions and tell it to load , then leave it while it flashes the box until it says complete
when you reboot the box , go through all the menus to setup different things like the screen and network , and the motor or fixed dish part too
then when finished assign a fixed ip for the dreambox in its menu , so that it always uses this same local ip address ( apart from when you are flashing it )
so eventually if the router is say 192.168.1.1 as a host , set the dreambox to say 192.168.1.15 or some other number a good 10 or more away from the router host , turning off dhcp and setting that last number manually and saving it
Thanks echelon....I did what you said about holding the front button down and got the IP of the box.... I pasted it in a browser and got a page saying something about ..' If you are seeing this page you haven't any Linux based operating system on the box'....I had the Dreambox Control Centre open and at this point the connection between the Pc..Router and Box..ie.(the green line) turns red and the connection is lost so i unplug the DB and plug it in again it then shows a Network...I then once again paste the IP of the box in the browser and it is at this point that i get the page i posted earlier....When I have done the first part to get the IP of the Box should i wait a little longer for something else to happen?
rgds.Tryharder
You've done better then me then, I am still in Enigma land, did you flash your box over a network or off a null modem lead?
i think its only possible to flash dm800Hd over network ive tried many times using null modem without success..
i open DreamUP And select Use Network and Flash TAB wait for Flash loader message to end then input IP of dream800HD into search bar at top on your web browser much faster this way too. ive successfully loaded only Nabilo blackhole image with keymap classic nuetrino mode plugin for remote and CCcam2.09 Newcs 160b working 100% ok and card reader reading my cyfra card 100% ok aswell,
good luck guys its a lovely box and a pleasure to work with only advice i would strongly suggest is to Forget gemini team and thier very "Dodgy" images and try a real great team NABILO Team image as they make always superb images... once again hats off to Nabilo Team on an excellent image thank you,
regrds,
barney
Nice one Dean, glad to hear you got there in the end mate
Many thanks -- easy when you know how
you dont need dcc open at all . or connected
just follow the instructions as listed , but its the little tiny button near the oled that you press whilst powering on , not the power button mentioned in the copy and paste , and then when it says boot , wait for the ip address , and note it down , then use that ip address in the web browser
once you have the web browser up , you will see some sort of loading screen in that browser , and use that to locate the file
rebooting the box means you have bypassed the loading screen as its booting up if you havent pressed the little button on powering up , which is why you are eventually seeing the web interface for the box , probably on a different ip ( but could be the same ip )
so just follow the instructions exactly as listed but its the little front button you hold , not the power button
Posting Permissions
Reply With Quote
Bookmarks