humax 5400 and tps

[shashouchesse]

hi to all
i'm french and i've got some problems to watch tps with my humax 5400 and the last toh 8.0
i put the hdf file for tps ( card + emu or card + amu + s) ans nothing..."0500 audio non disponible ou crypté"
can you help me please
thanks a lot
shashou

[ozzsurf]

put the clock gmt + 1 hour
ie if its say 12 oclock put to 1 oclock

[shashouchesse]

thanks for your help but i 've already tried this without result
any ideas?
thanks shashou

[shashouchesse]

when i put card +s + emu "cam ca statut 32"??????
what'am i doing wrong?
thanks for your help

[totothehero]

shashou*****e,

Is the signal OK ? Are the free channels clear ?
the hdf you have to upload to your humax changes every day: be sure to have the good one! It should work. Card+emu is enough (s is for card sharing).

Good luck.

[zad]

more than likley if your in france you want your normal time set!
is france not always +1 gmt?

ps you should only need caid set to card+emu unless your card sharing as well!

[shashouchesse]

thanks for your help but i've got a god signal and clear channels i tried with gmt+1 and gmt 0 but no............................... results

[McDude]

Are you using today's tps.bin (they are released daily)?

Have you checked to see that your TPS keys (non aes) are stored in your receiver? You can do this by going onto a TPS channel and then opening ram editor and seeing if the keys are not all 00000 under ident 007C00

Just to add. Make sure you wait for a channel to clear, around 20 seconds usually. Don't expect it to clear straight away

[shashouchesse]

ho!!!! when i'm going to ram editor then viacess all the key (for which provider) are 00000 and there is not a provider of tps

[supakev]

make sure you have todays tps.hdf file,use hu.upload or hnf smart to input the file to the reciever,check the clock is on gmt+1 and make sure u have a card in the slot with a valid atr any pre-programed fun,silver or gold card will work then leave on a tps channel for at least 30 seconds and it should clear.

[sat_rrstm]

ho!!!! when i'm going to ram editor then viacess all the key (for which provider) are 00000 and there is not a provider of tps

You have problems with DSR9500 tool,as I see,please go here :
https://www.satpimps.co.uk/showthread.php?t=61819 and follow the instuctions of post nr #5,and see if you can download properly the latest key-bin to your Hummy and check if you finally have keys in your Ram Editor.If you have,then download today's TPS.bin using HDFSmart to your Humax and tell us about the results.

[dainos]

Hello, I have found a tool to convert tps.bin to tps.hdf
Humax_AES_v1 1.zip. tried and works fine. Somthimes you get bin earlier then hdf. google it. dainos

[sat_rrstm]

Hello, I have found a tool to convert tps.bin to tps.hdf
Humax_AES_v1 1.zip. tried and works fine. Somthimes you get bin earlier then hdf. google it. dainos

There is a better tool called : tpsbinextractv1.3b!
You can run it every morning at 05:16 a.m. and it will download first tps.bin and convert it at once in TPS.hdf file,in a few seconds!!!
Go for it,I'm using it every day.

[Gone_Fishing]

ho!!!! when i'm going to ram editor then viacess all the key (for which provider) are 00000 and there is not a provider of tps

Doesn't work with out the keys

99.9% of humax problems are down to people thinking they
have loaded the keys when in fact they haven't, covered this
months ago

https://www.satpimps.co.uk/showpost.php?p=410377&postcount=6

TNT

[faucon9999]

Hi All,

I have the same problem as you Shashou*****e.

As of today I cannot clear TPS. Been working fine so far with the daily updates. I also noticed that I cant clear premiere today and that also was working fine for quite a long time. FTAs ,however, are coming in just fine.

Now when I try to manually load the new D+ keys I do find Nagravision but does not show up as 4010 as it normally does. So I guess i have a screwed up config somewhere but cant figure out what.

If anyone has ideas I d be very grateful.

THks

Faucon

[Gone_Fishing]

Hi All,

I have the same problem as you Shashou*****e.

As of today I cannot clear TPS. Been working fine so far with the daily updates. I also noticed that I cant clear premiere today and that also was working fine for quite a long time. FTAs ,however, are coming in just fine.

Now when I try to manually load the new D+ keys I do find Nagravision but does not show up as 4010 as it normally does. So I guess i have a screwed up config somewhere but cant figure out what.

If anyone has ideas I d be very grateful.

THks

Faucon

Did you read the link I posted ?

EMPTY your RAM then check it and it will say Nagravision
FFFF and all keys will be Zeros, then load new keys and
check again and it will say Nagravision 4101 and the keys
will be there

If you empty your ram and you dont see FFFF then you know
its a communication problem between dsr and humax


TNT

[faucon9999]

Thanks TNT . Followed your instructions and im back in business. Sorry for not reading carefully your earlier post....

Faucon

[Gone_Fishing]

No problem glad you sorted it


TNT

[shashouchesse]

HI THANKS FOR YOUR HELP
but i read all the post and my hummax doesn't work for tps...all the keys are 0000000 for all the provider for all encryption
when i load the key bin in dsr there's not a 007c00 provider for tps...
please...ibegin creasy.....soory for my poor english
again tahnks a lot
shahsou

[zad]

are you also uploading the daily tps file? the one in firmware format