Results 1 to 3 of 3

Thread: motorised sat dish help please.

  1. #1
    Verified Registered User
    Join Date
    Dec 2004
    Posts
    379
    Thanks
    0
    Thanked 0 Times in 0 Posts

    motorised sat dish help please.

    hi guys i,ve a 1.2m irte prime focus satelite dish and polarmount and actuator arm.
    its been set up years,but i feel its not pulling in all satelites like it use to.am not sure my dish was properly set up from day one.

    i am in southeast ireland and my nearest due south is 7.west

    Dish Setup Data
    Elevation: 29.6°
    Azimuth (true): 179.8°
    Azimuth (magn.): 183.2°
    LNB Skew [?]: -0.1°

    Latitude: 52.8***
    Longitude: -7.1***
    got the above from dishpointer by entering latitude.

    here are my details for 7.west so im almost spot on due south.

    my questions are,where do i set the degree,s mark to on polar mount?, and also the dish elevation ?.

    i know i keep the dish and polarmount straight and directly facing due south.

    but im not sure of the degree,s mark on polarmount declination as to where it should be set and also dish elevation.

    would this be the correct details for my latitude:

    elevation angle 37
    declination angle 7.552

    also theres a o to 10 scale to set the declination,but theres no scale to tell you the details on setting the elevation angle,all i have is the threaded bar which goes up and down to set elevation,but this is difficult cause of no o to 90 scale to work off.


    any help or advice would be truly appreciated,thanks

  2. #2
    V.I.P
    Join Date
    Dec 2004
    Posts
    2,982
    Thanks
    0
    Thanked 0 Times in 0 Posts
    The first thing you should check is that everything is still plumb, because if your pole isn't straight you'll never track the satellite arc correctly.
    Secondly although the set up angles are helpful, don't rely on them 100%.
    I would align your dish to 7W, peak the signal, then send your dish to the furthest East, then West, satellites, check the signal quality, then bring it back to 7W.
    Make some minor adjustments, if needed, peak the signal, again, then send it East, and West, and see if there's any improvement.
    You keep doing this until you're satisfied that the dish is tracking the arc correctly.

  3. #3
    V.I.P Detlef's Avatar
    Join Date
    Dec 2004
    Location
    Remagen [zGemma 2S, Vu+ duo, SS1, SS2HD, Foxsat 1000s & Foxsat HDR]
    Posts
    6,242
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Also I would be wary of quoting your location to that accuracy.

    It pinpoints your house to within about 10 metres.

    For giving advice on setting up a dish quoting your location to 0.1 degree would be sufficient.

    Or am I paranoid (but remember Tron).

Similar Threads

  1. VU+ Duo Motorised dish help
    By satlou in forum Vu+ Duo Help Section
    Replies: 23
    Last Post: 05-12-2014, 06:36 PM
  2. Replies: 5
    Last Post: 09-12-2013, 11:14 PM
  3. Motorised dish settings for 100cm motorised dish
    By VELMA in forum Dish Discussions
    Replies: 4
    Last Post: 29-11-2010, 10:30 AM
  4. 1 motorised dish & 1 fixed dish - 1 Rx
    By wsm25 in forum 5000 series
    Replies: 8
    Last Post: 17-12-2008, 03:07 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •