Results 1 to 20 of 20

Thread: Fooked up good and proper on my Icecrypt 1600chd

  1. #1
    Junior Member
    Join Date
    Dec 2014
    Posts
    21
    Thanks
    5
    Thanked 2 Times in 2 Posts

    Fooked up good and proper on my Icecrypt 1600chd

    after getting the scrambled message i attempted to update everything , and now i am left with Hotbird as the only statelite

    used to be plenty, usually Astra 28, sumat.. now there is still no programmes showing and all of it is in Italian anyway

    so i am at a total loss what to do next.. any help for my Icecrypt 1600chd please

  2. #2
    Verified Registered User
    Join Date
    Apr 2014
    Posts
    73
    Thanks
    45
    Thanked 62 Times in 33 Posts
    Have you tried a full factory reset? Yes, this will lose all the channels previously stored, put it's a starting point for loading everything back again

  3. #3
    Junior Member
    Join Date
    Dec 2014
    Posts
    21
    Thanks
    5
    Thanked 2 Times in 2 Posts
    Cheers for your reply, that were i am an the minute no channels at all , i have pressed all sorts of buttons trying to restore but nothing

    i also notice were the info for satellite position is its blank .. no longitude position or anything its all 000 000,were as before it would say the degrees etc.. and were the Astra 28 use to be with loads of others the is nothing now, at one point hotbird was the only on and thats gone now, so as you can see.. i have really messed everything up ,

    p.s never found the factory reset

  4. #4
    Verified Registered User
    Join Date
    Mar 2008
    Posts
    91
    Thanks
    30
    Thanked 41 Times in 26 Posts
    Are you trying to load Astra 28 or channels from another satellite?
    Do you not have a usb backup?
    Select menu got system then select upgrade by USB and select your backup
    Alternativley load the latest release upgrade by USB and this should bring the box back you will then have to scan the channels that you require
    hope this helps
    Attached Files Attached Files
    Last edited by Ross_37; 07-11-2015 at 06:54 PM.

  5. #5
    Junior Member
    Join Date
    Dec 2014
    Posts
    21
    Thanks
    5
    Thanked 2 Times in 2 Posts
    hi Ross,, trying to back on what i had last thursday which was everything , was always on the astra28 as i am in the UK, then friday it all said scrambled so i tried me best

    to upgrade pressing on whatever said upgrade, at one point it was all in Italian lol .. now when i swith on the is no satellite at all , hotbird was ther for a minute or two

    and the nothing, i think its because its not seeing my dish

  6. #6
    Verified Registered User
    Join Date
    Mar 2008
    Posts
    91
    Thanks
    30
    Thanked 41 Times in 26 Posts
    So what can you see?
    The menu?
    If so i would select system default setting then select upgrade by usb and load the latest firmware via usb to get to a stable position first

    Check under statellite installation that you have the 0/12volt on?
    Last edited by Ross_37; 07-11-2015 at 07:12 PM.

  7. #7
    Junior Member
    Join Date
    Dec 2014
    Posts
    21
    Thanks
    5
    Thanked 2 Times in 2 Posts
    trying that now

  8. #8
    Junior Member
    Join Date
    Dec 2014
    Posts
    21
    Thanks
    5
    Thanked 2 Times in 2 Posts
    sorry could notfind any 0/12 volt

  9. #9
    Verified Registered User
    Join Date
    Mar 2008
    Posts
    91
    Thanks
    30
    Thanked 41 Times in 26 Posts
    look on menu satellite, satlellite installation at the top you select satellite say astra 28.2 go down left hand side you will see lnb ect down to 0/12 volt

  10. #10
    Junior Member
    Join Date
    Dec 2014
    Posts
    21
    Thanks
    5
    Thanked 2 Times in 2 Posts
    yep thats right but all i have in that box is the number 1,no other number,,, LNB type ...universal ... tp index No TP...DiSEqC 1.0 ,,, disable and same for the DiSEqE 1.1disable.. positioner ,,DiSEqC1.2

    22k .. Off Polarity auto and LNB on

    hope this helps

  11. #11
    Verified Registered User
    Join Date
    Mar 2008
    Posts
    91
    Thanks
    30
    Thanked 41 Times in 26 Posts
    are you indicating that you have no satellites
    under menu satellite, satellite installation at the top if you select satellite do you have any at all? i.e astra 28.2, intelsat 907?

  12. #12
    Junior Member
    Join Date
    Dec 2014
    Posts
    21
    Thanks
    5
    Thanked 2 Times in 2 Posts
    yep nothing showing except 1

  13. #13
    Junior Member
    Join Date
    Dec 2014
    Posts
    21
    Thanks
    5
    Thanked 2 Times in 2 Posts
    thanks for your help but i think i have taken too much off your time i will try again later

  14. #14
    Verified Registered User
    Join Date
    Mar 2008
    Posts
    91
    Thanks
    30
    Thanked 41 Times in 26 Posts
    from what you have indicated you have lost your your channels
    if you have a backup install your backup. Menu, system, upgrade upgrade and then select channel. Alternativley select all ( software bios channels) an this should bring it all back
    leave it with you

  15. #15
    Super Moderator nml's Avatar
    Join Date
    Dec 2004
    Posts
    1,476
    Thanks
    3,232
    Thanked 1,692 Times in 854 Posts
    @angus5041,

    Could you please clarify the sats you want to receive and your setup ie single sat, Disqc switch or motor? I am not familiar with your receiver but if you make this clear i am sure that members like Ross_37 will be able to help.

  16. #16
    Junior Member
    Join Date
    Dec 2014
    Posts
    21
    Thanks
    5
    Thanked 2 Times in 2 Posts
    for almost a year i have had this icecrypt with very little trouble, it is a static dish and i did receive Astre 28, i am not too famillar with anything else i am sorry to say

    as in my previous post it has all gone i think i may have stupidly deleted everthing while trying to upgrade.

  17. #17
    Junior Member
    Join Date
    Dec 2014
    Posts
    21
    Thanks
    5
    Thanked 2 Times in 2 Posts
    many thanks to Ross for his help and patience

  18. #18
    Junior Member
    Join Date
    Dec 2014
    Posts
    21
    Thanks
    5
    Thanked 2 Times in 2 Posts
    Many many thanks to Ross 37 without whose help i would still be looking at a blank screen, and who took the trouble to email the firmware to me while on holiday,, top man

    ... the ice crypt box is a 1650 chd and not the 1600 as i first said it was sorry guys my mistake

  19. The Following User Says Thank You to angus5041 For This Useful Post:

    Bod (24-11-2015)

  20. #19
    Verified Registered User rockero's Avatar
    Join Date
    Dec 2009
    Posts
    78
    Thanks
    96
    Thanked 72 Times in 25 Posts
    hi all...S1600CHD is a great stb is great...I use it for 2 fixed dishes via diseq on 27.5W and 28.2E...could not ask for anything better....using tm5402 m2 for motorized but not got my head round that yet.....theres s.y package if you know someone how to sort it for you out there
    Last edited by rockero; 24-11-2015 at 02:43 AM.

  21. #20
    Junior Member
    Join Date
    Dec 2008
    Posts
    2
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Me too lol exactly the same - Mijas costa del sol. 80cm

Similar Threads

  1. Replies: 0
    Last Post: 04-11-2015, 01:48 AM
  2. Please help with icecrypt 1600chd
    By 123ichis in forum ICECRYPT
    Replies: 2
    Last Post: 20-10-2015, 12:42 PM
  3. have just bought an icecrypt 1600chd
    By turnitupmate in forum ICECRYPT
    Replies: 1
    Last Post: 30-03-2015, 06:18 PM
  4. Icecrypt S1600 CHD any good?
    By ginadr in forum ICECRYPT
    Replies: 10
    Last Post: 16-06-2014, 08:08 PM
  5. LNB Just Fooked Up
    By RABBY in forum General Chat
    Replies: 5
    Last Post: 10-02-2009, 07:31 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •