Results 1 to 4 of 4

Thread: Dummies guide to setting up Vu+ Duo2

  1. #1
    Goldwafers.co.uk LeeGW's Avatar
    Join Date
    Dec 2004
    Posts
    89
    Thanks
    20
    Thanked 505 Times in 42 Posts

    Dummies guide to setting up Vu+ Duo2

    Dummies guide to setting up Vu+ Duo2 by Lee Goldwafers.com

    Click Here to Buy Vu+ Duo2

    Useful Software

    7zip - http://www.7-zip.org/download.html
    Winrar - http://www.rarlab.com/download.htm
    Either of the above software can be used for unzipping the files.
    VuCC - https://www.satpimps.co.uk/showthrea...ol-Centre-V0-8


    1. Install image.

    Download a USB image file, eg Blackhole Image from
    https://www.satpimps.co.uk/forumdisp...Vu-Duo2-Images

    Unzip the BlackHole-vuduo2_usb.zip file and extract the vuplus folder to a USB PEN Drive.

    After unzipping to the pen drive you should have a folder on your pen drive named vuplus

    In the vuplus folder is another folder named duo2

    In the duo2 folder are 5 files.

    initrd_cfe_auto.bin
    kernel_cfe_auto.bin
    reboot.update
    root_cfe_auto.bin
    splash_cfe_auto.bin

    Power off Vu+ Duo2 with switch on the back
    Open the front flap on the right hand side.
    Insert USB Pen Drive into the front USB socket behind the front flap.
    Power on Vu+ Duo2

    When you see the "Update" message on the front display press the standby button (located behind the front flap)


    Once the image has been successfully installed the receiver will reboot automatically.


    2. Setup Motorised Dish using USALS
    First get your longitude & latitude info from _http://www.satsig.net/maps/lat-long-finder.htm

    Enter your post code into satsig.net and you'll get the correct LON & LAT info for your location.

    Example if I enter the following UK postal code: SE1 6JZ into _http://www.satsig.net/maps/lat-long-finder.htm

    I get the following LON & LAT:
    Longitude: -0.1042°
    WEST
    Latitude: 51.4979°
    NORTH


    Press Menu
    Select Setup Press OK
    Select Service searching Press OK
    Select Tuner configuration Press OK
    Select Tuner A Press OK

    Configure Tuner for Motorised Dish using USALS.
    Use the < > buttons on remote to select Simple.
    Use the down button to select mode and use the < > buttons to set to Positioner.

    Configuration Mode: Simple
    Mode: Positioner
    Longitude: 0.104 (Make sure you enter your own Longitude settings here)
    WEST
    Latitude: 51.497 (Make sure you enter your own Latitude settings here)
    NORTH

    Press OK to save.

    Press Menu
    Select Setup Press OK
    Select service searching Press OK
    Select Positioner Setup Press OK
    Select goto 0 Press RED Button

    Dish should now goto 1w.

    3. Upload a Channel List
    Download a pre-configured channel list example catseye's from

    https://www.satpimps.co.uk/forumdisp...gma-2-Settings

    For motorised dishes you'll want to look for this thread "Catseye Enigma 2 Settings File 75 East - 45 West All Satellites"
    Go to the last page in that thread to download the latest Catseye file.

    Unzip the Channel List to your local HDD.

    Example C:\Catseye E2 Settings File 75 East-45 West

    Use VuCC to upload channel list to Duo2.

    VUCC is an essential tool to have.
    Download VuCC From
    https://www.satpimps.co.uk/showthrea...ol-Centre-V0-8

    4. Install Cam

    A) Download CAM TGZ file from https://www.satpimps.co.uk/showthrea...le-Image-EMU-S


    B) or the newer 2013 or onwards versions (like v2.30) from


    https://www.satpimps.co.uk/showthrea...e2-emus-(2013)

    FTP the cam-filename.tgz or ipk file to the /tmp folder on Vu+ (usually this is var/tmp)

    Press Green Button then Yellow Button on Vu+ remote control.
    Select Manual Install Bh Package.
    Select the cam-filename.tgz file or ipk file (in ipk installer) and press OK.
    Message will appear - Do you want to install cam-filename.tgz (or ipk file)
    Select "Yes" and press OK.
    Message will appear - Installed.
    Press the exit button on remote a couple of times to come out of all the menus.

    6. Activate Cam
    Press the Blue button and use the < > buttons on remote to select the CAM
    Press OK to run the CAM.

    the cccam cfg file is located in var/etc after the correct cam emu has been installed
    ( On E2 Boxes the 3C.config is Located at /etc with Attributes set to 755 or All config files can be found in /etc )

    These instructions are for Blackhole Image other images button configurations might be slightly different.

    How to setup Vu+ with VBox II DiSEqC 1.2 Positioner.

    If your VBox II already has the satellite positions stored and your changing from an old receiver to Vu+ then follow this procedure.

    Write down your VBox II satellite position numbers. These are the numbers displayed on the front of the VBox II when moving to a
    specific satellite position. These position numbers can also be found in your old receivers motor setup menu.

    Example lets say...
    Position 1 on VBox II = Astra 19e
    Position 2 on VBox II = Eutelsat W2 16e
    Position 3 on VBox II = Hotbird 13e

    You get the idea...

    First send the dish to Astra 19e using Vbox II.

    On Vu+ Remote Press Menu
    Select Setup Press OK
    Select Service Searching Press OK
    Select Tuner configuration Press OK
    Select Tuner A Press OK

    Now set Configuration Mode to Advanced. Use Left or Right keys on remote to select.

    Configuration Mode: Advanced
    Satellite: Astra 19e
    LNB: 1
    DiSEqC mode: 1.2

    Scroll down to bottom of the page with the down arrow on remote.

    Use USALS for this sat: No
    Stored position: 001

    Press OK to store.

    OK that's Astra 19e setup now to setup Eutelsat W2 16e

    Now send the dish to Eutelsat 16E using Vbox II.

    Select Setup Press OK
    Select Service Searching Press OK
    Select Tuner configuration Press OK
    Select Tuner A Press OK

    Configuration Mode: Advanced
    Satellite: Eutelsat W2 16e
    LNB: 2
    DiSEqC mode: 1.2

    Scroll down to bottom of the page with the down arrow on remote.

    Use USALS for this sat: No
    Stored position: 002

    Press OK to store.

    OK that's Eutelsat W2 16e setup now to setup Hotbird 13e

    Now send dish to Hotbird using Vbox II

    Select Setup Press OK
    Select Service Searching Press OK
    Select Tuner configuration Press OK
    Select Tuner A Press OK

    Configuration Mode: Advanced
    Satellite: Hotbird 13e
    LNB: 3
    DiSEqC mode: 1.2

    Scroll down to bottom of the page with the down arrow on remote.

    Use USALS for this sat: No
    Stored position: 003

    Press OK to store.

    You get the idea, now repeat for the rest of the satellites and your done.

  2. The Following 30 Users Say Thank You to LeeGW For This Useful Post:

    ade1970 (26-11-2013), andrewcropper (25-09-2013), bluedevil65 (03-09-2015), catseye (16-09-2014), chelsea1 (09-01-2014), cuzz (20-12-2014), Daku (16-01-2014), doubleudee (28-05-2014), dxman (15-07-2019), echelon (31-07-2013), ekko star (01-08-2013), el bandido (26-09-2013), fishlos (14-01-2015), Gabstar16 (25-02-2017), gbmitie (03-08-2013), JForrester (02-03-2015), jovie (31-07-2013), kenwhelton (31-07-2013), lion2000uk (12-01-2014), Locoman (18-09-2015), makro41 (01-10-2013), norman (17-09-2013), ozzy30 (06-04-2014), Paul 48 (16-11-2017), peter32 (16-04-2015), Satfanni (17-08-2015), tinbin300 (11-09-2014), ubhi66 (12-08-2013), unimesh7Fowner (25-08-2013), voyager1972 (31-07-2013)

  3. #2
    Security Admin echelon's Avatar
    Join Date
    Dec 2004
    Posts
    12,732
    Thanks
    13,913
    Thanked 9,112 Times in 4,411 Posts
    Anybody with a windows pc or laptop can use this tool to determine the box was actually on the network -

    Advanced IP Scanner.

    See it in action and/or download from here:::
    Code:
    http://www.advanced-ip-scanner.com/index.php
    It's free for home use and it's quite a handy little tool.
    With just one button to click it becomes an extremely user friendly tool.
    A right click on an entry in the results pane opens up a list of options and tools such as ping, tracenet, telnet and ssh.

    It just takes a couple of seconds to scan a network and gives you the
    STATUS, NAME, IP, MANUFACTURER - and- MAC address of everything on your network in the results pane.

    Armed with this information it just is not possible to enter the wrong IP address in any software -
    either in the VuCC by Lee or in any ftp program such as filezilla without using the VuCC.

    thanks go to teduk for telling this forum about it

  4. The Following 9 Users Say Thank You to echelon For This Useful Post:

    Dave5118 (26-11-2013), doubleudee (28-05-2014), ferranvilaro (06-09-2015), fishlos (14-01-2015), Fuzzy_UK (29-03-2014), jamesjay (23-01-2014), peter32 (16-04-2015), squiddo (26-11-2013), tinbin300 (21-10-2014)

  5. #3
    Security Admin echelon's Avatar
    Join Date
    Dec 2004
    Posts
    12,732
    Thanks
    13,913
    Thanked 9,112 Times in 4,411 Posts
    consider the following forum comments to be preferred when setting up a VU box (any) or a dreambox (any) or any similar linux box

    I prefer to call it MANDATORY myself , but consider it "best practice" , especially for newbies to these boxes



    I ALWAYS set a password in BH on any linux box using BH or VIX or OpenPLI

    I also ALWAYS fix the IP address too, always have done on my old dm800 and tm9100 linux boxes

    so ALWAYS set a fixed ip and always change the password too , as soon as you install an image

    in this case I would set the box to something like 192.168.1.51 or higher


    ensure you have fixed the IP on the box , dont let it just choose its own as this will tend to change regularly depending on the order devices connect

    also ensure you have telnetted to the box and changed the password , or used the tuxbox commander password changer plugin

    then check your router admin panel and ensure you know the correct ip address for the box and that its logged onto the router (lan devices connected)


    The IP will only change if DHCP is set to yes in the box , and this really needs changing to no

    But this can only happen if the box has been turned off then on again in a different order to the last time it was used,ie last time was pc first then box,this time box first then pc.

    With DHCP set to on the router will automatically assign the lowest available ip,so if last time the pc was turned on first that would get 192.168.1.2 and the box would get 192.168.1.3

    just in case go into the router and look at the attached devices,this will tell you the IP thats assigned to the box,then go into the settings of the FTP program and ensure they match.if not change these settings to match the IP shown in the routers attached devices.


    set it to dhcp so all settings are correct , then untick dhcp and just alter to ip you want use the same one previously used saves me altering settings on pc.

    DCC is Dreambox Control Centre , an ftp and telnet program (plus other duties)

    DBedit is Dreamboxedit (used to load or save channel lists) - also used to edit existing channel lists (settings)

    Dreamset is another dreambox (or linux boxes like the vu) channel editor / loader

    VuCC is another useful tool including an ftp program (filezilla) - by author Lee

    many dreambox tools and programs can be used on VU linux boxes

    when checking the network on these boxes, you should use DCC , as DCC will tell you more about failures and DCC will allow a connection to any linux box , not just dreamboxes

    DCC is also used to telnet to the box and change the password using the passwd command

    routers can reserve the IP address you have chosen so that it always uses the same one anyway as the mac code is saved



    I use flash fxp and DCC as FTP programs

    DCC can also be used for telnet purposes which allow you to change the password and in my opinion it is imperative that people change the password as soon as possible after flashing an image. I have done this for about 7 to 8 years now, starting with my dreambox and also with vu boxes too

    it is the height of stupidity NOT to set a password on your box, same as the same can be said if you dont password your pc login or bank login or paypal login

    to stop ip addresses changing due to the switch on order of devices (like Ian said earlier) then you should fix the lan ip address of your vu box (or dreambox) and that way your FTP program will be set to use the same ip address , same name and same password each and every time you log into the box using it

    if it all stays the same, nothing changes, therefore is easier , simpler and no room for errors

    it would also stop somebody accessing your box and playing april fools on you by changing your box password (same applies to your router too)

    if you think about it, those default logins are what caused all the phone hacking scandal too (in simple terms)

    all seems common sense to me, nothing clever about it at all, its the K.I.S.S. principle

    I believe in setting a password so that the laptop or pc or dreambox or vu are "happy" , same with setting a fixed ip on all boxes, including non-linux , plus on a NAS too (its obvious to set login password and fixed ip address on a NAS)

    its important to do regular backups of your vu and your laptop or pc etc , if you dont , on your heads be it

    ------------------------------------

    Removing unwanted channels from your bouquet (channel list)

    you can either :-

    go onto the channel you wish to remove
    press the down button on the remote
    press menu - this brings up the onscreen channel editor
    make sure you are still on the unwanted channel
    now select "remove from bouquet"
    this will remove that channel
    repeat for any others you wish to remove from your channel list (bouquet)

    OR

    import into the latest dreamboxedit on your pc or laptop
    delete (remove) the unwanted channels
    save to pc (or laptop)
    send the amended list back to the dreambox (to your VU in this case)

    ----------------------------------------

    then restart enigma 2 from the menu (or restart or reboot the box)

    ----------------------------------------

    typical c line

    C: satpimps.gotdns.com 12345 pimps1name pimps1password yes

    typical n line

    N: someserver.dyndns.org 12345 pimps1name pimps1password 01 02 03 04 05 06 07 08 09 10 11 12 13 14

  6. The Following 5 Users Say Thank You to echelon For This Useful Post:

    ferranvilaro (06-09-2015), Jock77 (10-05-2015), Locoman (18-09-2015), mulvmaur (05-06-2015), peter32 (16-04-2015)

  7. #4
    Security Admin echelon's Avatar
    Join Date
    Dec 2004
    Posts
    12,732
    Thanks
    13,913
    Thanked 9,112 Times in 4,411 Posts
    SETTING UP CROSSEPG IN BH IMAGES

    PREPARATION

    ESSENTIAL TASKS BEFORE STARTING TO SETUP CROSSEPG

    Firstly, ensure you have a suitable usb stick and have formatted it on the duo using the format procedure in the BH image (blue button)

    Insert this stick when prompted AFTER THE IMAGE HAS BOOTED UP (ie:- do not insert the usb stick at all until prompted)
    I would recommend a stick of 16 gig or 32 gig and a branded make too (like the tiny red PNY 32 gig usb sticks from mr.memory), BH seems fussy about sticks and they can fail even if formatted correctly and you cannot really tell until you use them

    or try the ones in this thread

    https://www.satpimps.co.uk/showthrea...e-on-USB-stick

    When the stick is formatted you will be prompted to reboot so do so, and then MOUNT the stick as usb in the mountpoints manager

    The stick will be chosen and used for the epg download, and is also where you should store your picons too (not the hdd or the flash)

    format it as 1 partition using the modern EXT4 (for usb sticks - or the older EXT2) as your formatting options

    set it to usb in the mountpoints, then select it in crossepg

    ------------------------------------------------------------------------

    Now for Crossepg , which is embedded into BH images

    MENU - SETUP - CROSSEPG - CONFIGURE

    setup the following

    STORAGE DEVICE - USB STICK
    ENABLE CSV IMPORT - NO
    FORCE EPG RELOAD ON BOOT - YES
    SCHEDULED DOWNLOAD - DISABLED (or set to say 06.00am - once a day)
    SHOW AS PLUGIN - YES
    SHOW AS EXTENSION - YES
    SHOW FORCE RELOAD AS PLUGIN - YES

    press GREEN to save it

    now go back and update all the various providers first (rytec and opentv), then setup the following

    XMLTV PROVIDERS

    RYTEK UK XMLTV - GREEN TICK HERE (OK)
    (its the second choice from the bottom of the list) - GREEN to save it

    exit (back)

    use either the rytec above, or use opentv below , or use both if you need to

    OPEN TV PROVIDERS

    SKY UK OPEN TV (ASTRA 2 ON 28.2E) - GREEN TICK HERE (OK)
    (third choice down) - GREEN button to save it

    XEPGDB PROVIDERS - NOTHING SELECTED

    SCRIPTS - NOTHING SELECTED

    MHW2 PROVIDERS - NOTHING SELECTED

    PROVIDERS START ORDER (this can be your choice, or only use one option)

    RYTEK UK XMLTV
    SKY UK OPEN TV (ASTRA 2 ON 28.2E)

    -------------------------------------

    setup fast plugin using GREEN and GREEN by selecting crossepg reload

    or press GREEN (plugins) - RED (panel setup) and choose FAST PLUGIN SETUP and set crossepg download using the red button to select it

    this now allows you to quickly press GREEN TWICE to force an epg download/reload

    exit when the plugins menu shows over the top of BH RADIO or your plugins panel

    CROSSEPG should now be working and displaying more than now and next in extended epg and graphical epg

    ----------------------------------------------------------------------------------------

    use the coolmans plugin if you want an epg representation more like the vix image version

  8. The Following 9 Users Say Thank You to echelon For This Useful Post:

    bluedevil65 (03-09-2015), doubleudee (05-02-2017), ferranvilaro (06-09-2015), gmma03 (24-09-2016), hda5 (23-08-2015), launton (07-11-2016), Locoman (18-09-2015), Satfanni (23-08-2015), Tubbinpot (07-07-2016)

Similar Threads

  1. Dummies guide to setting up Vu+ Solo2
    By LeeGW in forum Vu+ Solo2 Help Section
    Replies: 9
    Last Post: 03-06-2015, 01:00 PM
  2. Dummies guide to setting up Vu+ Solo
    By LeeGW in forum Vu+ Solo Help Section
    Replies: 8
    Last Post: 11-04-2015, 12:06 AM
  3. Dummies guide to setting up Vu+ Duo
    By LeeGW in forum Vu+ Duo Help Section
    Replies: 15
    Last Post: 11-04-2015, 12:00 AM
  4. Dummies guide to setting up Uno
    By LeeGW in forum Vu+ Uno Help Section
    Replies: 2
    Last Post: 14-03-2015, 12:31 PM
  5. Dummies guide to setting up Vu+ Ultimo
    By LeeGW in forum Vu+ Ultimo Help Section
    Replies: 3
    Last Post: 26-11-2013, 01:24 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •