Results 1 to 4 of 4

Thread: How to FAQ for any HD Eaglebox

  1. #1
    Security Admin echelon's Avatar
    Join Date
    Dec 2004
    Posts
    13,156
    Thanks
    13,139
    Thanked 9,339 Times in 4,541 Posts

    How to FAQ for any HD Eaglebox

    How to load an EagleboxHD Softcam

    To load a softcam by USB:

    Extract the key file to a USB stick and insert it in your Eaglebox HD

    Menu - Setting - Upgrade - USB/Card Upgrade - /udska1

    Select the file

    Press OK and wait.. the receiver will reboot.

  2. The Following User Says Thank You to echelon For This Useful Post:

    hda5 (30-08-2012)

  3.    Advert



  4. #2
    Security Admin echelon's Avatar
    Join Date
    Dec 2004
    Posts
    13,156
    Thanks
    13,139
    Thanked 9,339 Times in 4,541 Posts
    To set time and date by PeeBee :-

    using your remote:

    select MENU

    press UP ARROW until you see the SETTING menu then press OK

    press DOWN ARROW until DATE TIME selected then press OK

  5. #3
    Security Admin echelon's Avatar
    Join Date
    Dec 2004
    Posts
    13,156
    Thanks
    13,139
    Thanked 9,339 Times in 4,541 Posts
    Using your remote to add or edit FAVS (Favourites) by PeeBee :-

    To Setup FAVs:

    Press the FAV button - you will now see a list of channels with an heading 1 to 8 for each of the FAVs

    - Select which FAV you want any channel to go in

    - For example - if want BBC channels to go into FAV1 - select each BBC channel in turn and press 1

    When you have done press EXIT and the changes will be saved.


    ---------------------------------------------------------------

    To use FAVS:

    Press OK to get a list of channels, then press the Green Button to get a list of FAV 1 to 8 - select the one you want.

    Note - you cannot change the names of FAV1 to FAV8

    When you are done I would then save your Database to a fat32 formatted usb stick

  6. #4
    Security Admin echelon's Avatar
    Join Date
    Dec 2004
    Posts
    13,156
    Thanks
    13,139
    Thanked 9,339 Times in 4,541 Posts
    by voyager1972

    Scanning

    to do a transponder scan,,,,it wont over write your channel lists.

    when you,re done back everything onto usb drive

    ------------------------------------------------

    To save settings to a USB Stick

    Menu - Setting - Upgrade - USB/Card Upgrade - /udska1

    Press the blue button to save all your settings.

    -----------------------------------------------

    To restore your settings:

    Menu - Setting - Upgrade - USB/Card Upgrade - /udska1

    Select the databasesys_yearmonthdate_hourmin sec.bin file and press OK

    The receiver will load the settings and reboot.

    ------------------------------------------------

    To configure a server by remote control:

    example

    server switch = on
    server address =eaglebox.yourdns.no-ip.org
    tcp port = 12345
    user name = user
    password = password

    ideally use the cfg file , alter it to suit and put onto the box afterwards from a fat32 usb stick

    --------------------------------------------

    and from A-SAT on setting up c lines etc

    The syntax for the line is

    {c,portnumber,servername.com,user name,password}

    First you must activate Super Setting where all the good stuff is, by the following:

    Menu -> Setting -> Version.

    When the Cursor is on the Version option, press the red button

    Enter the PIN 1510

    [the same process will disable Super Setting if it is enabled]

    Select Super Setting - press ok

    The first option allows you to select a C/S option - CCcam NewCamd - Avatar -eCAM or Disable.
    Avatar and eCam have no function in Europe.

    As each c/s option is selected, the relevant Config option appears highlighted. You may enter there and add your line details.
    To view what is there, and unhide the data, press the red button and enter the PIN 7878

    To check if all is ok, use the test option at the bottom of the config sub menu. It will attempt to connect, and give you a Success or Failure result.

    The other option in Super Setting is EMU.

    Use this if you have loaded a softcam. Its use is obvious and needs no explanation.

    To load super setting details:

    Edit the attached txt file to add the details you have been given.

    Copy it to a USB stick

    insert it in your Eaglebox HD

    Menu - Setting - Upgrade - USB/Card Upgrade - /udska1

    Select the file

    Press OK and wait.. the receiver will reboot.

    --------------------------------------------

    check these threads too

    http://www.satpimps.co.uk/showthread...-CCcam-trouble

    http://www.satpimps.co.uk/showthread...uot-but-not-so

  7. The Following User Says Thank You to echelon For This Useful Post:

    ac1cobra (22-02-2014)

Similar Threads

  1. EagleBox HD800
    By tommy in forum EagleBox HD800
    Replies: 10
    Last Post: 04-03-2013, 02:55 PM
  2. diseq 1.2 eaglebox
    By voyager1972 in forum EagleBox HD800
    Replies: 2
    Last Post: 01-09-2012, 09:35 AM
  3. eaglebox keys??
    By voyager1972 in forum EagleBox HD800
    Replies: 1
    Last Post: 29-08-2012, 10:56 PM
  4. EagleBox HD800
    By tommy in forum EagleBox HD800
    Replies: 0
    Last Post: 14-08-2012, 08:17 AM
  5. EagleBox HD softcam
    By Bod in forum SoftCam.Key
    Replies: 1
    Last Post: 07-08-2012, 09:45 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •