After i flashed latest BH image 1.7.0 all i get is a blank screen,revert back to previous image all ok what am i doing wrong?
After i flashed latest BH image 1.7.0 all i get is a blank screen,revert back to previous image all ok what am i doing wrong?
One of two things, you have not updated the CFE or you have a clone.
No its not a clone i have not updated the CFE tho, i'll give it a go tomorrow now thanks for info.
Please make sure you use the CFE for the Solo and NOT the Duo as I have ready many times.Originally Posted by charlie
It will kill your box.
The update take seconds to do.
https://www.satpimps.co.uk/showthrea...314#post829314
Loaded the CFE file this morning, updated new BH image all working ok, thanks to you all
Your welcome
Since iv'e updated im getting a lot of glitching on all my sea lions was ok for a while,reverted back to BH image 1.6.6 still glitches ,even tho i did a factory reset before loading old image, am i doing something wrong?
It's not going to be a problem with your box or image, more likely a problem with the sea lion.
Just found late last night my internet server was playing up all day, that would be the cause so i will revert to new image later on, very frustrating as the internet was only down for a few seconds at a time.
is it possible AFTER upgrading to new CFE , to setup an older version of BH? or i have to downgrade to 2.6.3.1 and how?
It seems from the point that i have installed 3.1.1 and BH 1.7.1 to have major problems with.....light. They even sent me an email telling me to disconnect till i find what causes to me to have no...light and also to them not to send them rubbish
You can downgrade with no issues but I do understand what you mean by having issues with light ?
i am afraid a can not tell it as it is ....My server told me tha i send him emm...whatever this is. Can i speak free or i must contact you via private message?
You can chat here just fine.
Just read the board rules if you are not sure.
Ok i will try to make it clear . Till now i had the old kernel 2.6.3.1.somewhat and the BH image ( i cannot remember the version ) . I decided to upgrade to kernel 3.1.1. and to setup the BH 1.7.1 image. The point that from now then i am dealing major problems with cccam and newcamd . I lost channels they seem to decode but still no picture . I got an email from my server they told me to put a # in front of all N lines cause i send them bad eem and i going to block all the cards (greek ) . So after one whole day of exchanging emails i decided to downgrade in order to get things going smoothly. Now the point is that i dont know how to do it and i am afraid to burn the solo....
Which is the safest way to do it and could you please help me doing it step by step .
Is it possible for the problem that occured to blaim the cccam 2.2.1 or the new image? It is very bizzare what happened
Note that i dont have a backup ( i think ) of the old module drivers. Of course i can choose what i want from the Vu+ archive as long as it is 2.6.3.1 . right?
One thing for sure is the image is not your problem.
What I suggest is you start CCCam via telnet and check the output.
Were you using a different version of CCcam before ?
Do not waste your time changing the image and drivers.
no i didnt change anything at all!! I use the same version and the same files they sent me. The only thing is that i didnt have it on my hdd and i downloaded again the 2.2.1 ccam. They told me that there is a trojan in the cccam and was sending them bad data. Is it possible that the cccam has a trojan?? and if so what should i do about it. They also told me that the cards from greek provider ( you know of course ) were programmed to do this in 2012 in order to stop working this way.
I dont know how to telnet the cccam. Kind of newbie. How do i do it and what i am supposed to see?
Select common interface and then reboot the box.
Start a telnet session the type this
cd /usr/bin
then CCcam_2.211 -d ( the CCcam_2.2.1 needs to be exactly as you find it in usr bin folder )
Then watch the output for anything strange, you can post the output here but remove all private info from it.
sonic
what are sea lions? lol
Ian.
Last edited by sonic1; 23-01-2012 at 02:24 PM. Reason: Removed real name from public view
Just use google m8
Sea Lion
Lol now I know why there are problems with BH and sea lions. They are just too heavy for the image to handle:respect-053: and must be needing a lot of space, looking at that google link
Last edited by A; 23-01-2012 at 07:50 PM.
Posting Permissions
Reply With Quote
Bookmarks