deltec
As Mickha says ?? Go into [ Network ] Press [ 1111 ] All will be revealed ?? GO TO [ Ethernet ] ?? Then you will see [ [ Client SETUP ] ?? Then you will see [ TYPE ] Make sure this says [ ON ]???
Your Login ID [ Should be there ] something like this [ 267m848888hk ] THIS IS ONLY A EXAMPLE
Connection status [ connected ]
Iff not you will have to [Register ] You will see this
Hope all is well:sifone:
were is the key editit says type above network
highlight network in ORANGEOriginally Posted by deltec
then press 1111 and KEY EDIT will appear above network in Accessory
you have gone INTO network instead of highlighting it
rabby`s instructions were wrong , mine and micka`s were correct
cant u do an idiots guide to seting up the spider box
I already have , and you gave me thanks for it on the 29th august 2011
its all there in black ,purple and blue
https://www.satpimps.co.uk/showthrea...allation-Guide post 5
still got no were im p i off 3 meter dish doing nothing been out of the hobay a while now shall i start again what u sugest
any boday please on this mater been at it all day im lost
any advise please un how to start again please
Start again tomorrow, read Echelons latest guide:
https://www.satpimps.co.uk/showthrea...allation-Guide
Can you please tell us what you have managed so far.
Have you switched on the extended menu, by entering the menu, going to Network and pressing 1111?
Have you located Ethernet, entered it and selected Register?
Is your Spiderbox connected to your router, using an ethernet cable?
What make/model router do you have?
You state you have a 3M dish, what is your general location?
What satellites/channels can you receive?
Have you loaded the latest patch, specific to youre version of the Spiderbox?
Which version of the Spiderbox do you have?
Hi M8
I don't think that you have missed anything in your post above, however deltec may have erased the original Mac address, please see post#6, and this is maybe why he is having so many problems getting connected and setting up the receiver.
Last edited by Aldo; 09-10-2011 at 01:51 AM.
my mac adress or ip adress is xxxxxxxx it says this on the router on my ip set it says 192.168.000.005 how do i put the leters using the remote control done every thing u told me to do still no suprise im stuck
MAC ADDRESS REMOVED BY ADMIN
DO NOT POST IT AGAIN
my mac from in side the spider box is********** on the mac adress it says ************ is this right
MAC ADDRESS REMOVED BY ADMIN
DO NOT POST IT AGAIN
i will keep trying to day when i put the usb stick in and out do u do a factory reset or not thank again for all ur help
iv done an update with the usb stick and it says oct tober 4
on a 9000 or 7000 you look through the top vents with a torch and you will see the mac address written on a label inside the spiderbox on the component board
write this down on a piece of paper , then go into menu-accessory-network , select Network just below Type , where it says IP Setup
The Mac Address is shown at the bottom above apply , check the details in there exactly match the ones you wrote down
DO NOT POST THE ACTUAL DETAILS ON HERE !!!
if they are the same , leave it alone !!
while you are in that menu you will see your router ip address
so something like this
IP address 192.168.000.005
SUBnet mask 255.255.255.000
Gateway 192.168.00.001
1st dns 192.168.000.001
2nd dns 000.000.000.000
Mac Address 01:231A:B8:C9
if that is similar to what I have written above , then your mac code and ip address are correct , so apply and exit , OR just exit
please note , the mac address shown above is an EXAMPLE , and not anyones actual mac address , that actual info is private !!
if the system info is showing oct 2011 then the patch seems to be in the box , so again exit ,
although mine says oct 7 2011 , not oct 4 2011
then follow the rest of my amended tutorial ( its amended into an idiot guide now , seeing as you asked)
https://www.satpimps.co.uk/showthrea...212#post817212
Posting Permissions
Reply With Quote
Bookmarks