Humax 5400z

[Marco]

Hello chicka,
i dont use Fausto i use sbcl and v-plug to get 39.e
you could use HoT 9.4 to latest patch to get these
anything lower than 9.4 you could have trouble with biss Incription
unless there is patch out to get these

[chicka]

Hello Marco,
Yes sbcl and vplug is very good too for 39E.
I have been trying to clear Digital Albania 16e with Humax Cardsharing box and Humax vip server but picture only clears for about 15 sec and than it freezes.
39E Bulsatcom and Srg have cleared OK with these methods.
P.S. Sorry I cannot PM you back as I only have 4 posts in this forum.
Chicka

[dejv]

just got my satellite with a motor last weekend.

i connected everything and when im changing the stations im getting a lot of channels scrambeled. mostly i can only see the italian channels.(italia uno etc)

i got the channel list from :
http://www.humax-zone.net/index.php?page=5400_settings

and downloaded;
GioppyGio Motor
Settings motor by GioppyGio 17-Mar-2010 08:40 103 kB

[mmg123]

Marco

I have been reading this thread over and over and i am still confused. I have a humax 5400z and have a static sat no motor x2 lnb,s 1 hotbird 2 nilesat. I have patched the receiver with hot,11.4b. ???? not clear on what settings to use or pmct table to use got latest key bin . And fausto and keys for that.

I want to view art/showtime ?????

Can you advise on settings and / pmct table/ to use. also i got a pmct table in cvs format that wasnt reconised in the humax tool suite i am useing that i was going to try.

At the stage at present i put orig firmware back on done all my tv antenna settings scanned my 2 sats . Then patched with the hot,11.4b Card cleaned and rewrote with irdeto script back in slot and accepted now patched.

Tried to explain has clear has i can hope you can help me further please.

Regards mmg123

[mmg123]

Ps Just had to download latest hot 1.15 because the other was freezing up on screen so had to re patched it with that. Edited Changed it back to hot 1.4b used cleaner first seems fine now .

[mmg123]

Can any one help me please. Humax 5400

[chicka]

Marco

I have been reading this thread over and over and i am still confused. I have a humax 5400z and have a static sat no motor x2 lnb,s 1 hotbird 2 nilesat. I have patched the receiver with hot,11.4b. ???? not clear on what settings to use or pmct table to use got latest key bin . And fausto and keys for that.

I want to view art/showtime ?????

Can you advise on settings and / pmct table/ to use. also i got a pmct table in cvs format that wasnt reconised in the humax tool suite i am useing that i was going to try.

At the stage at present i put orig firmware back on done all my tv antenna settings scanned my 2 sats . Then patched with the hot,11.4b Card cleaned and rewrote with irdeto script back in slot and accepted now patched.

Tried to explain has clear has i can hope you can help me further please.

Regards mmg123

Hello mmg123
As far as I know art/showtime is not open to view with any Key-bin or with Fausto at the moment unless you have an original card.
Humax with Toh 11.4 with Fausto will open some other channels like Bulsat*com on 39E.(I suppose you cannot see this since your dish is pointing to Hotbird and Nilesat???)
Chicka
Pmct: https://www.satpimps.co.uk/showthrea...880#post786880
Please See: Follow post 17 on this thread and they should clear
https://www.satpimps.co.uk/showthread.php?t=142640

[mmg123]

Thank you for your reply Chicka,

So unless i re- point my dish at bulsat i wont get anything.

When i look in my sat list in humax it does,nt list bulsat 39east so how would i go about finding the sat I do have a sat finder signal box but, like i am saying bulsat not listed.????

Kind Regards mmg123

[chicka]

Thank you for your reply Chicka,

So unless i re- point my dish at bulsat i wont get anything.

When i look in my sat list in humax it does,nt list bulsat 39east so how would i go about finding the sat I do have a sat finder signal box but, like i am saying bulsat not listed.????

Kind Regards mmg123

Hello mmg123,
I don't really know much about aligning a dish (maybe someone else in the forum can help you there).
Re: Bulsat 39e- Maybe it is not worth going through all the trouble of changeing your dish direction as there is a rumor that very soon Bulsat will change its encryption.
Re Nilesat: There are quite a number of FTA channels on Nilesat 7E --Dubai one, Mbc persia (movies), Mbc 2(Movies), Mbc 4 (Movies),Mbc Action (Movies), Mbc Max (Movies), Fox Series, Fox Movies, Fatafeat (cookery) Most programmes are English or American programmes.
Chicka

[mmg123]

Chicka thanks again for reply,


I have done a full clean of humax and just reflashed with toh hot 1.14 like you said then scanned my two sats Then just added latest keys bin nothing else has been done. only changed time to gmt + 2 which is correct for cyprus where i am. Have i done everything correct only it seems to freeze on channels main one free view bbc world news ??????.

I want to get this right because i have a space dish which i am going to setup to find bulsat leaveing my other were it is.

Can you be so kind has to guide me on the right tracks ???? something wrong with it freezing on bbc world news Like i said only flashed firmware and keys bin no settings or pmct Have i done it right for cyprus Oh i also wiped my funcard 4 and re wrote its oringal files back.


Kind Regards mmg123

[snakie]

If its freezing on free to air channels then something wrong..
could be power supply problem or bad signal ..
Is the box unresponsive on remote control when the channel freezes?
To get Hellasat in Cyprus look where the sun is at 10:30 - 11 am
And you have to adjust the skew of the lnb,put it in the middle and then turn it little bit so the lnb out will look at left side of the dish while you are looking it from infront.

[chicka]

Hello mmg123,
Sorry for the late reply. I have been very busy visiting a sick relative.
As Snakie says: It should not freeze on a FTA channel.and please answer his question: "Is the box unresponsive on remote control when the channel freezes?"

Try this:
With your remote. Press Menu- configuration=
Card + Emu
Card blocker: Off
Hsic
Nagra au: Off
and see if it still freezes.

1)There is no need to clean you Humax Decoder to change to a different Toh Hot. Just send the toh Hot to the decoder.
2) Re Funcard: The Funcard that I am using in my Humax has never been updated in any way and I have been using it for over 5 years.

For further help re: aligning your dish, there is this site, just input your address, zoom in and it will give you all the details:

http://www.dishpointer.com/

Chicka

[mmg123]

Thank you snakie and chicka, There,s no rush just very pleased for your help ( Sorry to hear about relative hope they are alright ) NO RUSH

Thank you both for this very useful information I will go about setting my other dish up towards weekend and let you know if i get it correct with the link you provided.

I changed the settings as you said in the toh config Unfortunately it didn,t work it still freezes on a fta channel. Yes non responsive on remote, You press to go up or down a channel and the volume go,s dead first and then it just wont go anywhere (The picture does not freeze thou )

King Regards mmg123

[chicka]

Hello mmg123,
The Key-bin is used to open encrypted channels and not to see Free To Air ones.
The Key-bin will not work without a Pmct table. (maybe it is freezing because you did the key-bin without the Pmct ????)
The only thing I can suggest is to do everything again in this sequence:
No need to clean previous:
1) Toh Hot 11.4 for your particular decoder (5400Z or 5400Z+)
2) Channel list (If it is installed or you have scanned, there is no need to do it again)
3) Pmct
4) Humax Key-bin

Make sure funcard is in Humax slot.
Humax configuration:
Card+Emu
Card Blocker: off
Hsic
Nagra Au: Off

Maybe Snakie or Marco can give you more advice to solve freezing problem.
Let us know how it goes
Chicka

[mmg123]

Ok thank you Chicka

I will do has you say but i am losted has to which pmct table to use ???? now Got the toh hot11.4 you have listed and key bin i think if its the latest one out now .

I did scan my two sats after loading patch then just put key bin in.

[chicka]

Ok thank you Chicka

I will do has you say but i am losted has to which pmct table to use ???? now Got the toh hot11.4 you have listed and key bin i think if its the latest one out now .

I did scan my two sats after loading patch then just put key bin in.

Hello mmg123,
Pmct:
https://www.satpimps.co.uk/showthrea...880#post786880
Humax Key-bin
https://www.satpimps.co.uk/showthrea...881#post786881
Chicka

[snakie]

Ok if it freezes like you say it could be 2 things.
Big channel list with lots of user defined buquets - favorites or power supply problem.
Once it freezes disconnect the lnb cable from it and see if its ok.
If that helps then you need to take it for a cleanup and fix of the power supply.

[mmg123]

Ok guys thanks,

Will do has you say, Start with full clean out and re-patch.

1 cleaner firmware
2 patch
3 antenna settings and Channel scan
4 pmct
5 key bin


Is that in the right order to be done. Because i have no channel list settings to put in. So i just scan my own sats.

And thats it.


Or do i,

1 cleaner firmware then ( Do my antenna settings and scan channels )
2 Patch ( Do nothing just proceed with no 3 )
3 Pmct ( In
4 Key bin ( In
5 Do toh hot config settings card - emu etc

Done and test

[mmg123]

Cleaned inside the box spotless and it still freezes ??????????

[snakie]

Power supply??