Added support for CCcam .
Added support for CCcam .
And support for via 2.6
And here is the keys for via2.6 for mgcamd
http://www.mediafire.com/?twhlnimtu4l
Last edited by tsakman; 20-01-2010 at 10:42 PM.
Am I missing somthing where do we get 1.35a from? I've found 1.35 but not 1.35a.
Last edited by Smudger; 20-01-2010 at 11:30 PM.
yes, work fine (BIS, JSC+ , SCT )
Mgcamd 1.35
download directly Azbox from techsat camd server
http://techsat.info/AZCamd
the cccam client it s work very nice and stable ; good job team
note change mg_cfg for your config
Is this version working on Azbox HD? If yes, also as CCcam Client? Better than MlutiCAS' CCcam client??
cu
KJ
You should have a look at myazbox
yes its running fine on azbox
in my opinion on orf better that multicas
but i have problems with polsat
hi guys installed this directly from server. deactivated multicas and dvabi and placed mgcamd as top priority. however does not appear to be working and when i check ip:16001 nothing appears?
am i missing something?
Working VERY well... Very good job, very cool!!!
Now, can we have Mbox added, too, please...
Oh, Kanber, m8: can we have a nice mgcamd.info plugin, please...
==============================
Try the file attached to this message...
This is what I did:
-added the Via 2.6 keys to SoftCam.Key,
-added AutoRoll.Key,
-edited the mgcamd_cfg [G line to 41 = 01 Newcamd + 08 GBox + 32 CCcamd].
Then, one must:
-rename peer.cfg.example and cccamd.list.example to
peer.cfg and cccamd.list,
-edit peer.cfg and cccamd.list.
peer.cfg:
M: { my.dyndns.org { mypass}}
#
D: { peer’sserver.dyndns.something { myport hisport { hispass { A3 A3 }}}}
D: { peer’sserver.dyndns.something { myport hisport { hispass { A3 A3 }}}}
cccamd.list:
C: peer.DynDNS.something port username password
Then, send them to mgcamd folder in your AZbox HD via FTP.
Give CHMOD to 755 -> mgcamd and AutoRoll.Key.
This is just to be a client.
Dunno if what I did was 100% correct but it works. Tested!
=====================
If you have an original card and you want to combine MGcamd with NewCS card reader/server you will have to edit it some more...
Search this forum for info...
Good luck!
Last edited by goran; 21-01-2010 at 01:47 AM.
hi guys sorry to be a pain. but i have installed mgcamd. set c and flines in mg_cfg. deactivated all other cams and put mgcam main priority. what am i missing ? chmod perhaps?
MGcamd is only a client of CCcam (up to 2.1.1), so no F lines.
Only C lines in cccamd.list
Works fine even with the 2.1.2 and 2.1.3 , i
I didn't tested MGcamd with cccam, but some say it just works up to 2.1.1
It's good to know it works with more recent CCcam versions.
It's a bit slow to open channels but it works nicely... As in stable and well!
@Goran
Did you set priority.list?
Also did you set de P line in mg.cfg?
Standard it's Gbox, newcamd,CCcam
P: { 00 }
CCcam, Newcamd, Radegast, Gbox
P: { 02 }
Thanx for drawing my attention to it.
No, I haven't touched it, as it just worked...
So, maybe I will try prioritising CCcam now and see...
In my opinion, mgcamd is the most stable one at the moment
It is great news that mgcamd also supports now cccam client mode
Then there's another option:
Code:# network mode, use summ for several clients # 00 no network (default) # 01 newcamd netclient # 02 radegast netclient # 04 camd3 netclient # 08 gbox netclient # 32 cccamd netclient, card list saved as /tmp/cccamd.info # (ECM only, supported server version up to 2.1.1, later not work) G: { 41 }
Only CCcam:
G: { 32 }
CCcam + Newcamd
G: { 33 }
Bookmarks