MultiCAS Version 1.61C-A08
Changelog:
-Multicas + newcs + cccamd/dvbapi combination is working fine
-Disconnect cardreader now possible
... just found it on another forum...
MultiCAS Version 1.61C-A08
Changelog:
-Multicas + newcs + cccamd/dvbapi combination is working fine
-Disconnect cardreader now possible
... just found it on another forum...
does this mean it accepts nlines and clines all on multicas now?
Now we have a possibility to put in the newcamd server details, too!
It is possible to sort it all out via remote:
Home -> Plug-ins -> OpenXCAS -> Camd Setup -> MultiCAS -> Smartcard Interface -> SC Splitter and CS -> roll the options to Client CCcam or Client NewCamd and add as required...
The relevant config files to discuss:
cardreader.cfg
Sorry, I do not yet have a smartcard, so can't help too much...###### Disable or Enable option for cardreader of MultiCAS
###### Disable_CardReader = 1 -> Disable-Internel CardReader / Disable_CardReader = 0 -> Enable-Internel CardReader
Disable_CardReader = 0
newcamd.cfg
priocaid.cfg## MAX Support the 12 of Serverlist by this CFG file
## N: Hostname port username password 01 02 03 04 05 06 07 08 09 10 11 12 13 14
================================= ==============### 0100 : SECA
### 0500 : VIACESS
### 06xx : IRDETO
### 0dxx : CRYPTOWORKS
### 0bxx : CONAX
### 09xx : NDS
### 17xx : BETACRYPT
### 18xx : NAGRA
###----------------------------------------------------
### max 8 of caid 0100 0500 0600 0900 1800 0d00 0b00 1700
###----------------------------------------------------
### CASE OLD #1 0600 0d00 1700 1800 0900 0b00 0100 0500
### CASE OLD #2 0100 1800 0500 0600 0d00 1700 0b00 0900
###---------------------------------------------------
0100 1800 0500 0600 0d00 1700 0b00 0900
One way of editing it all is using telesat's MultiCAS Edit.
================================= ===============
Here is the "how to" for 2 more options, from how to install it to how to edit it - easily:
0) Home -> Plug-ins -> OpenXCAS -> no more Manual Install option, guys! It is now DOWNLOAD EXECUTABLE -> you will see the links of support servers to get your plug-ins there, guys... [ get it from http://azboxworld.com ]
1) Download and install: MultiCAS 160... well, the latest - always!
2) Get the configuration files for EMUs/CS SW from DOWNLOAD CONFIG. So, one must download MultiCAS CCcam config files. But not needed for this one, if you had the previous version of MultiCAS already installed and it was all functioning.
At this point it is good to reboot your AZbox HD!
3) So, off we go to Home -> Plug-ins -> [as described above...] -> MultiCAS -> using your remote control -> Smart Card Splitter and CS.
4) Change the following, using your REMOTE:
-change the Mode to Client CCcam [if, like me, you have no smartcard to play with and share] - you can connect to other people's servers
-choose Server No. 1 [when done with the first one, move this one to 2, then 3 etc. - as many as you need, up to 16, I think...]
-choose Host Name Use - write something like: something.dyndns.org [whatever the data you get from your server/peer is, like gorski.dyndns.org or whatever your server is called like - I DO NOT HAVE A SERVER, THIS IS ONLY AN EXAMPLE!!!],
-choose the Port - 12000 or whatever it is that your peer tells you to use
-User Name - whatever it is [you must have a username that normally your peer gives you and put in his server to allow you access to his server]
-Password - whatever it is [like above]
-Server - Enable
-Connect - test it [but only AFTER I enabled the one which appears below it, on the TV screen...]
It should say "login success"...
Repeat for all the servers you have, to check...
Red Button = Save.
5) But still: as soon as I wanted to get out of there using the Exit button on my remote, it first asked me, in a little pop-up window, if I want to login to all my servers now. Press OK, of course. It will connect to your peers aaaaaand....
...once in a TV channels list, the connection was fast!!! Let's just leave it at that. Pink/Total TV [Irdeto/N*D*S]: vroom, vrooooommmm!!! :sifone: If not, change the channel and then it should connect! If not - reboot and check again...
================================= ==============
Here is how to install it from a file you get on a forum like this one:
FileZilla -> into AZbox HD -> Plugins -> OpenXCAS -> MultiCAS -> delete all "example" files, openxcas.conf and multicas emu_module.
Put in openxcas and emu_module files from a file one gets from a forum like this one.
Give emu_module CHMOD to 755.
Reboot.
The right version should be showing in AZbox HD MultiCAS menu. All servers should be preserved, if you put them in before!
Server details are in MultiCAS in /tmp file: ccc_serverstatus.info
Good luck!:sifone:
Btw, I suppose that if we disable the MultiCAS card reader [using the cardreader.cfg file], we can activate NewCS alongside MultiCAS and use the 2 together.
So, if we activate NewCS 1.20 RC13 to use the internal card reader and we are servers to our peers, using Newcamd protocol, then we can have a full Newcamd package in NewCS + MultiCAS' Client NewCamd mode?
Would it be good enough for whatever it is we need...???<newcamdserver>
<enabled>yes</enabled>
<name>local</name>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<user>
<name>dummy</name>
<password>dummy</password>
<au>on</au>
<sidoverride>off</sidoverride>
<hostname>127.0.0.1</hostname>
<port>22000</port>
</user>
</newcamd_server>
<httpd>
<server>
<port>8080</port>
<enabled>yes</enabled>
</server>
<user>
<name>azhd</name>
<password>azhd</password>
<accesslevel>admin</accesslevel>
</user>
</httpd>
</newCSconfig>
Hi goran,
if we have no local card and want to use both newcamd and cccam as client and both at the same time, should we edit the file "cardreader.cfg" and set "Disable_CardReader = 1"?
I hope that with this version, N lines and C lines are possible simultenously.
Thanks
rmt
Have just tested this and can't get C-lines and N-lines to work at the same time.
:-(Originally Posted by xln747
Is this that complex to get both running at the same time?
My opinion:
They dont want to spend time for this now and have other priorities.
I use currently multicas for C lines and if I want to use the N lines, I switch off multicas and activate mgcamd.
guys, one thing....
why would we want to use dvbapi for native cccam with multicas?
i just use cccam 2.1.1 + multicas connected.
cccam dvbapi deactivated...why would i want to use dvapi at same time?
Are you sure that you can use Native CCCAm without load DVBAPI?
I think that you cannot use cccam without dvbapi.....
You can use CCcam without DVBAPI, but will not open channels by itself.
CCcam will work just as a server (connects to all your peers in server and client mode) and then connects to MultiCAS running in the same azbox to open channels.
Hi hfmls,
thanks for your reply, but this is not what I meant.
I dont use dvbapi for cccam, i use multicas.
Multicas has now both newcamd client and cccam client support.
But they donīt work together (newcamd client and cccam client).
This is my problem.
I expect that if multicas has both newcamd client and cccam client interfaces, so they should also run at the same time (from within multicas, not separately without a need of dvbapi).
They are both there.
Why dont they get both run at the same time?
i think multicas onyl uses clines if only u dont have the channel in your newcamd line. i know what i said is not what you asked lol :P
i have cccam server without dvapi in azbox hd.
then multicas to connect to cccam server.
but, why would i want dvbapi from native cccam + multicas at same time?
i don't understand that in changelog.
im wondering the same what means in changelog dvbapi, it would be better if dvbapi could open or connect to a server with hop lower than multicas if this one connects to a upper hop. no?
Maybe the dvapi_module is nog intergrated within multicas
But i don't know
well i would love if dvbapi would be as stable as multicas.
maybe multicas guys could work on it?
You don't need multicas to run newcamd & cccam clients at the same time . Now you can share your card with newcs connected to cccamd if multicas cardreader feature is deactivated ; it has no importance if dvbapi exists or not if u give muticas a higher priority than cccamd in emu list from menu .
All you have to do is to start all 3 (multicas , newcs and cccamd) , connect newcs to cccamd (nline in cccamd.cfg) and internal share your card to multicas (fline in cccamd and cline in multicas) . You can also share your card to external peers either by cccamd(fline) or by newcs (add more users in newcs.xml) .
Cheers ,
Val .
Can we use (dvbapi and cccamd) for client
like on the first native cccam releases for azbox?
I can t test right now...
This changelog is a bit confusing..
Never mind the CCcam, as it's too buggy and unstable, freezes quickly when zapping.
What if we want to do it only with NewCS + MultiCAS? How would you see it working, Val?
Newcamd protocol for internal reader [via NewCS to read the card and be a server to your peers] + MultiCAS as CCcam client to your peer's CCcam servers. In that case you lose your own card opening the package you're subscribed to?
Have you tried it, please? What would be needed in terms of settings/config files/lines?
Thanx!
you can!
the doubt that change log generates is this:
cccam native + dvbapi = server and watches channels
cccam native + multicas = server and watch channels
cccam native + multicas + dvbapi = server and watch channels, but what will azbox hd use to watch channels?!? dvbapi or multicas? and what is the benefict to have both?!
Hi valerica, thanks for detailed answer.
I donīt have any local card.
What I have: 2x cccam server and 2x newcamd server to connect
In a native cccam on DMM, I can connect to both via cccam config which includes both C lines and N lines.
But since native cccam on Azbox is not stable, I use multicas.
Multicas does not achieve the same or is there a solution to this?
Posting Permissions
Reply With Quote
Bookmarks