Damn maturity rating. Any other way than conax cam?

[bonovox]

Yeah new digit alb card and the damn things set up by blocking the xxx channels. Is there any other way of altering the maturity rating than having to buy a damn conax cam. Using dreambox 7020 or 800 here so is there a softcam that can do it?

[sonic1]

With Newcs you can try pincode and protected sid.

I know it works with Tring but I have not tested with Digitalb
I would use version 1.66 as I have some problems with 1.67 and protected pin.

[bonovox]

I'm not familiar with that cam but I'll give it a go. Thanks for the tip.

[bonovox]

Nah cant get it to work with that. Damn thing.

[bobbyboil]

you can do it in a clarke tech hd50000 receiver

[sonic1]

I'm not familiar with that cam but I'll give it a go. Thanks for the tip.

What are you using to view the card at present ?

[bonovox]

What are you using to view the card at present ?

CCcam2.0.11 at present.

I have tried Newcs1.66/CCcam_2.1.1 and configured the xml file with pin code and protected sid and it wouldn't open the xxx channels but worked ok on everything else.

@compass
Yep tried this and it didn't work on this card. Its a new card. I have tried your suggested method before on an older card, probably a couple of years ago and it worked fine. Would the reason be it won't work now cos Digitalb have since gone to a different version of conax card? It read the ATR of the card fine but wouldn't execute the script. I kept getting error timeout 2A message.

[sonic1]

Are you trying to open the mpeg4 channels ?

If yes then you will not succeed, there is no know public fix for this at present.

[^^COMPASS^^]

CCcam2.0.11 at present.

I have tried Newcs1.66/CCcam_2.1.1 and configured the xml file with pin code and protected sid and it wouldn't open the xxx channels but worked ok on everything else.

@compass
Yep tried this and it didn't work on this card. Its a new card. I have tried your suggested method before on an older card, probably a couple of years ago and it worked fine. Would the reason be it won't work now cos Digitalb have since gone to a different version of conax card? It read the ATR of the card fine but wouldn't execute the script. I kept getting error timeout 2A message.

Well it's possible,

I will do some digging around & if i turn any think up will add it to this thread.

do you not know anybody with a Tm receiver as you could use the card slot to change the maturity rating this way.

Regards Compass...

[^^COMPASS^^]

Yeah new digit alb card and the damn things set up by blocking the xxx channels. Is there any other way of altering the maturity rating than having to buy a damn conax cam. Using dreambox 7020 or 800 here so is there a softcam that can do it?

Here you go

Configure Win-explorer to work with your phoenix interface (3,57MHz).

To do so set the comport, the baud-rates to 9600, parity even and 2 stop bits with direct byte convention. Check both 'Flush...' fields and check if 'ISO Reset' on the 'Advanced' page is enabled too.
Now put your card in the reader and do Card->Analyse ATR. If you get 3b240030423030 your can finally change the maturity rating level.
If you still have probs you maybe have to adjust the timeouts. If you get an ATR but it doesnt look right, check the freq of your phoenix - should be 3,57 MHz.

Depending on the pin of your card, take the appropriate line and copy it into the 'Script file:' window - execute and that's it.
PIN 0000:
dd26000007 r01 1f053030303008 r02
PIN 1234:
dd26000007 r01 1f053132333408 r02

You should get something like this, last line depends if the PIN was correct or not.
RX ATR : 3B 24 00 30 42 30 30
TX Data : DD 26 00 00 07
RX Data : 26
TX Data : 1F 05 31 32 33 34 08
RX Data : 90 00 <- PIN ok, code set to new value (08 == X- Erotic)
RX Data : 90 17 <- PIN wrong

Regards compass