Results 1 to 6 of 6

Thread: tm5400ci

  1. #1
    V.I.P drahcirk's Avatar
    Join Date
    Jan 2006
    Posts
    765
    Thanks
    18
    Thanked 6 Times in 4 Posts

    tm5400ci

    had this box for over 6months and still dont know how u turn on biss tried the yellow button ,that dont work, any input please,.

  2. #2
    V.I.P Giga's Avatar
    Join Date
    Feb 2009
    Posts
    4,170
    Thanks
    0
    Thanked 16 Times in 9 Posts
    go on c l o s e d channel
    8 2 8 0
    select a l i n e
    enter the k e y

  3. #3
    V.I.P drahcirk's Avatar
    Join Date
    Jan 2006
    Posts
    765
    Thanks
    18
    Thanked 6 Times in 4 Posts
    thanks g, i loaded the keys by 232, and put in 8280, on a closed channel ,but, it still says off,

  4. #4
    V.I.P Giga's Avatar
    Join Date
    Feb 2009
    Posts
    4,170
    Thanks
    0
    Thanked 16 Times in 9 Posts
    are you running a patched software?
    from remote select
    menu
    system information
    it should show a version number with p
    below you would see these menu's:
    C A S and B I S S
    if you don't see these?
    if you did enter that sequence 8 2 8 0 you would get in the B I S S menu for that channel.
    there you would enter the K E Y on a line from the remote.
    As far as I know B I S S is not passed by uploading?
    this is how it works for super TM 5200D USB, 5300D+
    USB, 5600 CI USB & 5400 CI+ USB. It could be different for non super?
    these k e y s have a verry short lifespan (most of them)

  5. #5
    V.I.P drahcirk's Avatar
    Join Date
    Jan 2006
    Posts
    765
    Thanks
    18
    Thanked 6 Times in 4 Posts
    once again thanks g, it says s/w version 1.69p may 26, 09, in biss it says off in the top right hand corner,.

  6. #6
    V.I.P Giga's Avatar
    Join Date
    Feb 2009
    Posts
    4,170
    Thanks
    0
    Thanked 16 Times in 9 Posts
    now comes the hard part, keying in the data:
    with remote cursor of remote (ch-) drop down until first line is marked.
    all numbers from keypad
    all alpha input press info key:
    • 1 x = A
    • 2 x = B
    • 3 x = C
    • 4 x = D
    • 5 x = E
    • 6 x = F

    important with numbers it jumps to the next possition.
    with alpha you have to move the cursor to the right (V+)
    when finished press exit and confirm save with yes.
    try this out with the 1st line until you have the hang of it.
    if the channel want open, be sure you have fresh code (most only 1 day working, or even less) check the code for typo.
    if your are using this a lot, it might be good to keep track what line you used for what channel.
    you only have 40 lines of these for all channels.
    Last edited by Giga; 06-07-2009 at 07:18 AM. Reason: 40 lines

Similar Threads

  1. tm5400 super won,t blindscan.
    By liamski in forum 5000 series
    Replies: 16
    Last Post: 27-01-2009, 03:11 AM
  2. TM5400ci
    By etch in forum 5000 series
    Replies: 5
    Last Post: 31-12-2008, 07:33 PM
  3. 5000 series channel editing question
    By beanman in forum 5000 series
    Replies: 5
    Last Post: 28-06-2008, 09:54 AM
  4. tecnomate 5400+c
    By barron in forum 5000 series
    Replies: 13
    Last Post: 08-06-2008, 08:10 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •