Dummies guide to setting up Vu+ Zero

Dummies guide to setting up Vu+ Zero by Lee Goldwafers.com

Click Here to Buy Vu+ Zero

Useful Software
7zip - http://www.7-zip.org/download.html
Winrar - http://www.rarlab.com/download.htm
Either of the above software can be used for unzipping the files.
VuCC - https://www.satpimps.co.uk/showthrea...ol-Centre-V0-8

Initial set-up procedure.
Connect infra-red remote eye to the IR Sensor connector at the rear.
Insert USB Pen Drive containing the image you want to install into the USB socket at the rear.
Connect LAN cable from router to the Ethernet socket at the rear.
Connect Satellite Dish feed cable to the "LNB in" connector at the rear.
Connect HDMI lead from TV to the HDMI socket at the rear.
Connect power supply input to the 12V input socket at the rear and plug the PSU into the mains power.
Switch on unit using the power switch at the rear.

1. Install image.
Download a USB image file, eg Blackhole Image from
https://www.satpimps.co.uk/forumdisp...Vu-Zero-Images

Unzip the BlackHole-vuzero_usb.zip file and extract the vuplus folder to a USB PEN Drive.

After unzipping to the pen drive you should have a folder on your USB pen drive named vuplus

In the vuplus folder is another folder named zero

Power off Vu+ Zero with switch on the back.
Insert the USB Pen Drive into the USB socket on the back.
Power on Vu+ Zero.

The white LED on the left side of the front panel will begin pulsing.

The pulsing indicates it's flashing the image.

Once the image has successfully flashed the pulsing will stop and change to blinking on and off.

When the white LED is blinking on and off it's now safe to power off with the switch on the back and remove the USB Pen Drive.

Power on again to reboot the receiver, job done.

2. Setup Motorised Dish using USALS
First get your longitude & latitude info from _http://www.satsig.net/maps/lat-long-finder.htm

Enter your post code into satsig.net and you'll get the correct LON & LAT info for your location.

Example if I enter the following UK postal code: SE1 6JZ into _http://www.satsig.net/maps/lat-long-finder.htm

I get the following LON & LAT:
Longitude: -0.1042°
WEST
Latitude: 51.4979°
NORTH

Press Menu
Select Setup Press OK
Select Service searching Press OK
Select Tuner configuration Press OK
Select Tuner A Press OK

Configure Tuner for Motorised Dish using USALS.
Use the < > buttons on remote to select Simple.
Use the down button to select mode and use the < > buttons to set to Positioner.

Configuration Mode: Simple
Mode: Positioner
Longitude: 0.104 (Make sure you enter your own Longitude settings here)
WEST
Latitude: 51.497 (Make sure you enter your own Latitude settings here)
NORTH

Press OK to save.

Press Menu
Select Setup Press OK
Select service searching Press OK
Select Positioner Setup Press OK
Select goto 0 Press RED Button

Dish should now goto 1w.

3. Upload a Channel List
Download a pre-configured channel list example catseye's from

https://www.satpimps.co.uk/forumdisp...gma-2-Settings

For motorised dishes you'll want to look for this thread "CATSEYE E2 settings lists (VARIOUS SATELLITES)"
Go to the last page in that thread to download the latest Catseye motor file (Catseye E2 Settings File 75 East-60 West.rar).

Unzip the Channel List to your local HDD.

Example C:\Catseye E2 Settings File 75 East-45 West

Use VuCC to upload channel list to Zero.

VUCC is an essential tool to have.
Download VuCC From
https://www.satpimps.co.uk/showthrea...ol-Centre-V0-8

4. Install Cam
Download CAM IPK file from https://www.satpimps.co.uk/showthrea...%29-%282014%29

FTP the cam-filename.ipk file to the /tmp folder on Vu+ (usually this is var/tmp)
Press Green Button then Yellow Button on Vu+ remote control.
Select Manual Install IPK Package.
Select the cam-filename.ipk file and press OK.
Message will appear - Do you want to install cam-filename.ipk
Select "Yes" and press OK.
Message will appear - Installed.
Press the exit button on remote a couple of times to come out of all the menus.

5. Activate Cam
Press the Blue button and use the < > buttons on remote to select the CAM
Press OK to run the CAM.

These instructions are for Blackhole Image other images button configurations might be slightly different.

How to setup Vu+ with VBox II DiSEqC 1.2 Positioner.

If your VBox II already has the satellite positions stored and your changing from an old receiver to Vu+ then follow this procedure.

Write down your VBox II satellite position numbers. These are the numbers displayed on the front of the VBox II when moving to a
specific satellite position. These position numbers can also be found in your old receivers motor setup menu.

Example lets say...
Position 1 on VBox II = Astra 19e
Position 2 on VBox II = Eutelsat W2 16e
Position 3 on VBox II = Hotbird 13e

You get the idea...

First send the dish to Astra 19e using Vbox II.

On Vu+ Remote Press Menu
Select Setup Press OK
Select Service Searching Press OK
Select Tuner configuration Press OK
Select Tuner A Press OK

Now set Configuration Mode to Advanced. Use Left or Right keys on remote to select.

Configuration Mode: Advanced
Satellite: Astra 19e
LNB: 1
DiSEqC mode: 1.2

Scroll down to bottom of the page with the down arrow on remote.

Use USALS for this sat: No
Stored position: 001

Press OK to store.

OK that's Astra 19e setup now to setup Eutelsat W2 16e

Now send the dish to Eutelsat 16E using Vbox II.

Select Setup Press OK
Select Service Searching Press OK
Select Tuner configuration Press OK
Select Tuner A Press OK

Configuration Mode: Advanced
Satellite: Eutelsat W2 16e
LNB: 2
DiSEqC mode: 1.2

Scroll down to bottom of the page with the down arrow on remote.

Use USALS for this sat: No
Stored position: 002

Press OK to store.

OK that's Eutelsat W2 16e setup now to setup Hotbird 13e

Now send dish to Hotbird using Vbox II

Select Setup Press OK
Select Service Searching Press OK
Select Tuner configuration Press OK
Select Tuner A Press OK

Configuration Mode: Advanced
Satellite: Hotbird 13e
LNB: 3
DiSEqC mode: 1.2

Scroll down to bottom of the page with the down arrow on remote.

Use USALS for this sat: No
Stored position: 003

Press OK to store.

You get the idea, now repeat for the rest of the satellites and your done.

setting a password on a VU box (or any linux box)

https://www.satpimps.co.uk/showthrea...nnecting/page2

---------------------------------------

adding a c line to a vu box

ftp to var/etc and edit the cccam.cfg

copy and paste your line into this config and save it

exit

restart cccam

you will find this info in the sticky threads at the top of this forum and in the other VU and dreambox discussion forums here too

no idea about macs but the principle must be the same as in windows

on a windows pc , ftp is used with VuCC and filezilla , dreambox control centre (DCC) , flash fxp , putty and many other ftp programs

consider the following forum comments to be preferred when setting up a VU box (any) or a dreambox (any) or any similar linux box

I prefer to call it MANDATORY myself , but consider it "best practice" , especially for newbies to these boxes


I ALWAYS set a password in BH on any linux box using BH or VIX or OpenPLI

I also ALWAYS fix the IP address too, always have done on my old dm800 and tm9100 boxes

so ALWAYS set a fixed ip and always change the password too , as soon as you install an image

in this case I would set the box to something like 192.168.1.51 or higher


ensure you have fixed the IP on the box , dont let it just choose its own as this will tend to change regularly depending on the order devices connect

also ensure you have telnetted to the box and changed the password , or used the tuxbox commander password changer plugin

then check your router admin panel and ensure you know the correct ip address for the box and that its logged onto the router (lan devices connected)


The IP will only change if DHCP is set to yes in the box , and this really needs changing to no

But this can only happen if the box has been turned off then on again in a different order to the last time it was used,ie last time was pc first then box,this time box first then pc.

With DHCP set to on the router will automatically assign the lowest available ip,so if last time the pc was turned on first that would get 192.168.1.2 and the box would get 192.168.1.3

just in case go into the router and look at the attached devices,this will tell you the IP thats assigned to the box,then go into the settings of the FTP program and ensure they match.if not change these settings to match the IP shown in the routers attached devices.


set it to dhcp so all settings are correct , then untick dhcp and just alter to ip you want use the same one previously used saves me altering settings on pc.


when checking the network on these boxes, you should use DCC , as DCC will tell you more about failures and DCC will allow a conenction to any linux box , not just dreamboxes

DCC is also used to telnet to the box and change the password using the passwd command

routers can reserve the IP address you have chosen so that it always uses the same one anyway as the mac code is saved



I use flash fxp and DCC as FTP programs

DCC can also be used for telnet purposes which allow you to change the password and in my opinion it is imperative that people change the password as soon as possible after flashing an image. I have done this for about 7 to 8 years now, starting with my dreambox and also with vu boxes too

it is the height of stupidity NOT to set a password on your box, same as the same can be said if you dont password your pc login or bank login or paypal login

to stop ip addresses changing due to the switch on order of devices (like Ian said earlier) then you should fix the lan ip address of your vu box (or dreambox) and that way your FTP program will be set to use the same ip address , same name and same password each and every time you log into the box using it

if it all stays the same, nothing changes, therefore is easier , simpler and no room for errors

it would also stop somebody accessing your box and playing april fools on you by changing your box password (same applies to your router too)

if you think about it, those default logins are what caused all the phone hacking scandal too (in simple terms)

all seems common sense to me, nothing clever about it at all, its the K.I.S.S. principle

I believe in setting a password so that the laptop or pc or dreambox or vu are "happy" , same with setting a fixed ip on all boxes, including non-linux , plus on a NAS too (its obvious to set login password and fixed ip address on a NAS)

its important to do regular backups of your vu and your laptop or pc etc , if you dont , on your heads be it

short tutorial on flashing the box from usb stick

try BH 217 or openBH (or the latest BH file if using BH) from here
(or you could try the new openvix hades 18 from the openvix firmware site)

THEN

download the file, UNPACK it with 7zip

format a usb stick that is between half a gig to 8 gig in size to fat32 on your laptop or pc using windows explorer

copy and paste the previously unpacked folder VUPLUS to the stick

switch the solo2 box off completely using the mains switch

place the usb stick in the FRONT usb socket

turn the solo2 box on, and wait while it reads the stick

if all goes well it will program the box

then it will tell you to remove the usb stick and reboot

turn the solo2 box off at the mains and remove the stick

turn the solo2 box back on again and see if it boots up

if it does follow the onscreen wizards

bear in mind these procedures are nothing like your old boxes , there will still be a lot of work to do, which is why the tutorials are here

if it fails, assume the box is faulty (or a clone) -
but try several usb sticks before deciding this, these boxes can be VERY fussy about usb sticks

-------------------------------------

Removing unwanted channels from your bouquet (channel list)

you can either :-

go onto the channel you wish to remove
press the down button on the remote
press menu - this brings up the onscreen channel editor
make sure you are still on the unwanted channel
now select "remove from bouquet"
this will remove that channel
repeat for any others you wish to remove from your channel list (bouquet)

OR

import into the latest dreamboxedit on your pc or laptop
delete (remove) the unwanted channels
save to pc (or laptop)
send the amended list back to the dreambox (to your VU in this case)

----------------------------------------

then restart enigma 2 from the menu (or restart or reboot the box)

----------------------------------------

typical c line

Quote:

---

C: satpimps.gotdns.com 12345 pimps1name pimps1password yes

---

typical n line

Quote:

---

N: someserver.dyndns.org 12345 pimps1name pimps1password 01 02 03 04 05 06 07 08 09 10 11 12 13 14

---

Quote:

---

Originally Posted by echelon

setting a password on a VU box (or any linux box)

https://www.satpimps.co.uk/showthrea...nnecting/page2

---------------------------------------

adding a c line to a vu box

ftp to var/etc and edit the cccam.cfg

copy and paste your line into this config and save it

exit

restart cccam

you will find this info in the sticky threads at the top of this forum and in the other VU and dreambox discussion forums here too

no idea about macs but the principle must be the same as in windows

on a windows pc , ftp is used with VuCC and filezilla , dreambox control centre (DCC) , flash fxp , putty and many other ftp programs

---

Hi

i have pretty much follow the steps from the thread above but it seems something is missing. I have the epg correctly but no picture. I have flushed the image. installed the ipk file, upload channel list and insert the clines.
is anything else i am missing?
What do you mean with restart ccam after insert the cline?

Thanks

ensure your cccam is enabled in the menu, then restart the box as explained in the above tutorial

if necessary, do a full restart from hte menu shutdown section , this will "reboot" the box

once restarted , make sure cccam is selected and running and ensure you have a valid and working internet connection